[PATCH 8/9] dt-bindings: mtd: Split ECC engine with rawnand controller

From: Xiangsheng Hou
Date: Sun Nov 27 2022 - 21:08:35 EST

Split MediaTek ECC engine with rawnand controller and convert to
YAML schema.

Signed-off-by: Xiangsheng Hou <xiangsheng.hou@xxxxxxxxxxxx>
---
.../bindings/mtd/mtk,nand-ecc-engine.yaml | 60 ++++++
.../devicetree/bindings/mtd/mtk-nand.txt | 176 ------------------
.../devicetree/bindings/mtd/mtk-nand.yaml | 92 +++++++++
3 files changed, 152 insertions(+), 176 deletions(-)
create mode 100644 Documentation/devicetree/bindings/mtd/mtk,nand-ecc-engine.yaml
delete mode 100644 Documentation/devicetree/bindings/mtd/mtk-nand.txt
create mode 100644 Documentation/devicetree/bindings/mtd/mtk-nand.yaml

diff --git a/Documentation/devicetree/bindings/mtd/mtk,nand-ecc-engine.yaml b/Documentation/devicetree/bindings/mtd/mtk,nand-ecc-engine.yaml
new file mode 100644
index 000000000000..80321157e928
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/mtk,nand-ecc-engine.yaml
@@ -0,0 +1,60 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mtd/mtk,nand-ecc-engine.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MediaTek(MTK) SoCs NAND ECC engine
+
+maintainers:
+ - Xiangsheng Hou <xiangsheng.hou@xxxxxxxxxxxx>
+
+description: |
+ MTK NAND ECC engine can cowork with MTK raw NAND and SPI NAND controller.
+
+properties:
+ compatible:
+ enum:
+ - mediatek,mt2701-ecc
+ - mediatek,mt2712-ecc
+ - mediatek,mt7622-ecc
+
+ reg:
+ items:
+ - description: Base physical address and size of ECC.
+
+ interrupts:
+ items:
+ - description: ECC interrupt
+
+ clocks:
+ minItems: 1
+ items:
+ - description: clock used for the controller
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - clocks
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/mt2701-clk.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+
+ soc {
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ bch: ecc@1100e000 {
+ compatible = "mediatek,mt2701-ecc";
+ reg = <0 0x1100e000 0 0x1000>;
+ interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&pericfg CLK_PERI_NFI_ECC>;
+ };
+ };
+
diff --git a/Documentation/devicetree/bindings/mtd/mtk-nand.txt b/Documentation/devicetree/bindings/mtd/mtk-nand.txt
deleted file mode 100644
index 4d3ec5e4ff8a..000000000000
--- a/Documentation/devicetree/bindings/mtd/mtk-nand.txt
+++ /dev/null
@@ -1,176 +0,0 @@
-MTK SoCs NAND FLASH controller (NFC) DT binding
-
-This file documents the device tree bindings for MTK SoCs NAND controllers.
-The functional split of the controller requires two drivers to operate:
-the nand controller interface driver and the ECC engine driver.
-
-The hardware description for both devices must be captured as device
-tree nodes.
-
-1) NFC NAND Controller Interface (NFI):
-=======================================
-
-The first part of NFC is NAND Controller Interface (NFI) HW.
-Required NFI properties:
-- compatible: Should be one of
- "mediatek,mt2701-nfc",
- "mediatek,mt2712-nfc",
- "mediatek,mt7622-nfc".
-- reg: Base physical address and size of NFI.
-- interrupts: Interrupts of NFI.
-- clocks: NFI required clocks.
-- clock-names: NFI clocks internal name.
-- ecc-engine: Required ECC Engine node.
-- #address-cells: NAND chip index, should be 1.
-- #size-cells: Should be 0.
-
-Example:
-
- nandc: nfi@1100d000 {
- compatible = "mediatek,mt2701-nfc";
- reg = <0 0x1100d000 0 0x1000>;
- interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_LOW>;
- clocks = <&pericfg CLK_PERI_NFI>,
- <&pericfg CLK_PERI_NFI_PAD>;
- clock-names = "nfi_clk", "pad_clk";
- ecc-engine = <&bch>;
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
-Platform related properties, should be set in {platform_name}.dts:
-- children nodes: NAND chips.
-
-Children nodes properties:
-- reg: Chip Select Signal, default 0.
- Set as reg = <0>, <1> when need 2 CS.
-Optional:
-- nand-on-flash-bbt: Store BBT on NAND Flash.
-- nand-ecc-mode: the NAND ecc mode (check driver for supported modes)
-- nand-ecc-step-size: Number of data bytes covered by a single ECC step.
- valid values:
- 512 and 1024 on mt2701 and mt2712.
- 512 only on mt7622.
- 1024 is recommended for large page NANDs.
-- nand-ecc-strength: Number of bits to correct per ECC step.
- The valid values that each controller supports:
- mt2701: 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 28,
- 32, 36, 40, 44, 48, 52, 56, 60.
- mt2712: 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 28,
- 32, 36, 40, 44, 48, 52, 56, 60, 68, 72, 80.
- mt7622: 4, 6, 8, 10, 12, 14, 16.
- The strength should be calculated as follows:
- E = (S - F) * 8 / B
- S = O / (P / Q)
- E : nand-ecc-strength.
- S : spare size per sector.
- F : FDM size, should be in the range [1,8].
- It is used to store free oob data.
- O : oob size.
- P : page size.
- Q : nand-ecc-step-size.
- B : number of parity bits needed to correct
- 1 bitflip.
- According to MTK NAND controller design,
- this number depends on max ecc step size
- that MTK NAND controller supports.
- If max ecc step size supported is 1024,
- then it should be always 14. And if max
- ecc step size is 512, then it should be
- always 13.
- If the result does not match any one of the listed
- choices above, please select the smaller valid value from
- the list.
- (otherwise the driver will do the adjustment at runtime)
-- pinctrl-names: Default NAND pin GPIO setting name.
-- pinctrl-0: GPIO setting node.
-
-Example:
- &pio {
- nand_pins_default: nanddefault {
- pins_dat {
- pinmux = <MT2701_PIN_111_MSDC0_DAT7__FUNC_NLD7>,
- <MT2701_PIN_112_MSDC0_DAT6__FUNC_NLD6>,
- <MT2701_PIN_114_MSDC0_DAT4__FUNC_NLD4>,
- <MT2701_PIN_118_MSDC0_DAT3__FUNC_NLD3>,
- <MT2701_PIN_121_MSDC0_DAT0__FUNC_NLD0>,
- <MT2701_PIN_120_MSDC0_DAT1__FUNC_NLD1>,
- <MT2701_PIN_113_MSDC0_DAT5__FUNC_NLD5>,
- <MT2701_PIN_115_MSDC0_RSTB__FUNC_NLD8>,
- <MT2701_PIN_119_MSDC0_DAT2__FUNC_NLD2>;
- input-enable;
- drive-strength = <MTK_DRIVE_8mA>;
- bias-pull-up;
- };
-
- pins_we {
- pinmux = <MT2701_PIN_117_MSDC0_CLK__FUNC_NWEB>;
- drive-strength = <MTK_DRIVE_8mA>;
- bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
- };
-
- pins_ale {
- pinmux = <MT2701_PIN_116_MSDC0_CMD__FUNC_NALE>;
- drive-strength = <MTK_DRIVE_8mA>;
- bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
- };
- };
- };
-
- &nandc {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&nand_pins_default>;
- nand@0 {
- reg = <0>;
- nand-on-flash-bbt;
- nand-ecc-mode = "hw";
- nand-ecc-strength = <24>;
- nand-ecc-step-size = <1024>;
- };
- };
-
-NAND chip optional subnodes:
-- Partitions, see Documentation/devicetree/bindings/mtd/partition.txt
-
-Example:
- nand@0 {
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- preloader@0 {
- label = "pl";
- read-only;
- reg = <0x00000000 0x00400000>;
- };
- android@00400000 {
- label = "android";
- reg = <0x00400000 0x12c00000>;
- };
- };
- };
-
-2) ECC Engine:
-==============
-
-Required BCH properties:
-- compatible: Should be one of
- "mediatek,mt2701-ecc",
- "mediatek,mt2712-ecc",
- "mediatek,mt7622-ecc".
-- reg: Base physical address and size of ECC.
-- interrupts: Interrupts of ECC.
-- clocks: ECC required clocks.
-- clock-names: ECC clocks internal name.
-
-Example:
-
- bch: ecc@1100e000 {
- compatible = "mediatek,mt2701-ecc";
- reg = <0 0x1100e000 0 0x1000>;
- interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_LOW>;
- clocks = <&pericfg CLK_PERI_NFI_ECC>;
- clock-names = "nfiecc_clk";
- };
diff --git a/Documentation/devicetree/bindings/mtd/mtk-nand.yaml b/Documentation/devicetree/bindings/mtd/mtk-nand.yaml
new file mode 100644
index 000000000000..47a1334bcddd
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/mtk-nand.yaml
@@ -0,0 +1,92 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mtd/mtk-nand.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MediaTek(MTK) SoCs raw NAND FLASH controller (NFC) device tree bindings
+
+maintainers:
+ - Xiangsheng Hou <xiangsheng.hou@xxxxxxxxxxxx>
+
+allOf:
+ - $ref: "nand-controller.yaml#"
+
+properties:
+ compatible:
+ enum:
+ - mediatek,mt2701-nfc
+ - mediatek,mt2712-nfc
+ - mediatek,mt7622-nfc
+
+ reg:
+ items:
+ - description: Base physical address and size of NFI.
+
+ interrupts:
+ items:
+ - description: NFI interrupt
+
+ clocks:
+ minItems: 2
+ items:
+ - description: clock used for the controller
+ - description: clock used for the pad
+
+ clock-names:
+ minItems: 2
+ items:
+ - const: nfi_clk
+ - const: pad_clk
+
+ nand-ecc-engine:
+ description: Required ECC Engine node
+ $ref: /schemas/types.yaml#/definitions/phandle
+
+ "#address-cells":
+ const: 1
+
+ "#size-cells":
+ const: 0
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - clocks
+ - clock-names
+ - nand-ecc-engine
+ - "#address-cells"
+ - "#size-cells"
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/mt2701-clk.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+
+ soc {
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ nandc: nfi@1100d000 {
+ compatible = "mediatek,mt2701-nfc";
+ reg = <0 0x1100d000 0 0x1000>;
+ interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&pericfg CLK_PERI_NFI>,
+ <&pericfg CLK_PERI_NFI_PAD>;
+ clock-names = "nfi_clk", "pad_clk";
+ nand-ecc-engine = <&bch>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ bch: ecc@1100e000 {
+ compatible = "mediatek,mt2701-ecc";
+ reg = <0 0x1100e000 0 0x1000>;
+ interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&pericfg CLK_PERI_NFI_ECC>;
+ };
+ };
--
2.25.1