Re: [PATCH v4 00/23] ufs: qcom: Add HS-G4 support
From: Andrew Halaney
Date: Fri Dec 02 2022 - 15:52:00 EST
On Thu, Dec 01, 2022 at 11:13:05PM +0530, Manivannan Sadhasivam wrote:
> Hello,
>
> This series adds HS-G4 support to the Qcom UFS driver and PHY driver.
> The newer Qcom platforms support configuring the UFS controller and PHY
> in dual gears (i.e., controller/PHY can be configured to run in two gear
> speeds). This is accomplished by adding two different PHY init sequences
> to the PHY driver and the UFS driver requesting the one that's required
> based on the platform configuration.
>
> Initially the ufs-qcom driver will use the default gear G2 for enumerating
> the UFS device. Afer enumeration, the max gear supported by both the
> controller and device would be found out and that will be used thereafter.
> But for using the max gear after enumeration, the ufs-qcom driver requires
> the UFS device to be reinitialized. For this purpose, a separate quirk has
> been introduced in the UFS core along with a callback and those will be used
> by the ufs-qcom driver.
>
> This series has been tested on following platforms:
>
> * Qcom RB5 development platform powered by SM8250 SoC
> * SM8450 based dev board
>
> Merging Strategy:
> -----------------
>
> The PHY patches are expected to go through PHY tree and UFS, MAINTAINERS
> patches are expected to go through SCSI tree.
>
> NOTE: Since this series targets multiple SoCs (base like SM8350) and
> (derivative like SC8280XP), testing on all of these platforms is really
> appreciated. Although, if the series works for base SoC, then for derivatives
> also it should work.
Tested-by: Andrew Halaney <ahalaney@xxxxxxxxxx> # Qdrive3/sa8540p-ride
Without this patch series, the board's operating in gear 3. With it the
board's operating in gear 4. Gentle reminder sa8540p-ride is a SC8280XP
derivative.
I'm not really proficient in storage benchmarking, but a simple dd test
showed the following (sorry for the poor output, console got a
little wacky on the output).
Gear 3:
[root@localhost ~]# dd bs=4k oflag=direct if=/dev/zero of=/dev/disk/by-partlabel/userdata
dd: error writing '/dev/disk/by-partlabel/userdata': No space left on device
19873276+0 records in
19873275+0 records out
81400934400 bytes (81 GB, 76 GiB) copied, 864.111 s, 94.2 MB/s
[root@localhost ~]# dd bs=4k if=/dev/disk/by-partlabel/userdata of=/dev/null
19873275+0 records in
19873275+0 records out
81400934400 bytes (81 GB, 76 GiB) copied, 75.7823 s, 1.1 GB/s
[root@localhost ~]#
Gear 4:
[root@localhost ~]# dd bs=4k oflag=direct if=/dev/zero of=/dev/disk/by-partlabel/userdata
[ 81.651598] ufshcd-qcom 1d84000.ufs: ufs_qcom_get_hs_gear: 296: UFS_HS_G4
[ 81.658592] ufshcd-qcom 1d84000.ufs: ufs_qcom_pwr_change_notify: 731: Agreed gear: 4
[root@localhost ~]# GB, 76 GiB) copied, 738.015 s, 110 MB/s
[root@localhost ~]# dd bs=4k if=/dev/disk/by-partlabel/userdata of=/dev/null
19873275+0 records in
19873275+0 records out
81400934400 bytes (81 GB, 76 GiB) copied, 63.9846 s, 1.3 GB/s
[root@localhost ~]#
So a bit of a performance gain was seen with this patch series :)
Thanks,
Andrew
>
> Thanks,
> Mani
>
> Changes in v4:
>
> * Dropped HS G3 specific setting from SM8350 default init sequence
> * Added G4 support to SM8350 and SC8280XP
> * Covered all qcom files under drivers/ufs/host in MAINTAINERS file
> * Added missing Suggested-by tags for Can Guo
> * Rebased on top of linux-next 20221201
>
> Changes in v3:
>
> * Dropped the "device-max-gear" DT property and switched to reinitialization (Krzysztof)
> * Added HS-G4 support to all compatible SoCs (SM8150, SM8250 and SM8450). This will also
> benefit the derivative SoCs of these platforms like SC8180x, SC8280x etc...
> * Splitted the qmp_phy_init_tbl changes into separate patches (Vinod)
> * Collected reviews from Andrew H
>
> Changes in v2:
>
> * Collected reviews from Dmitry
> * Renamed "max-gear" property to "max-device-gear"
> * Used min() for deciding which gear to use instead of open comparision
> * Added comment about the old register name
>
> Manivannan Sadhasivam (23):
> phy: qcom-qmp-ufs: Remove _tbl suffix from qmp_phy_init_tbl
> definitions
> phy: qcom-qmp-ufs: Rename MSM8996 PHY definitions
> phy: qcom-qmp-ufs: Move register settings to qmp_phy_cfg_tbls struct
> phy: qcom-qmp-ufs: Add support for configuring PHY in HS Series B mode
> phy: qcom-qmp-ufs: Add support for configuring PHY in HS G4 mode
> phy: qcom-qmp-ufs: Move HS Rate B register setting to tbls_hs_b
> phy: qcom-qmp-ufs: Add HS G4 mode support to SM8150 SoC
> phy: qcom-qmp-ufs: Add HS G4 mode support to SM8250 SoC
> phy: qcom-qmp-ufs: Avoid setting HS G3 specific registers
> phy: qcom-qmp-ufs: Add HS G4 mode support to SM8350 SoC
> phy: qcom-qmp-ufs: Add HS G4 mode support to SM8450 SoC
> phy: qcom-qmp-ufs: Add HS G4 mode support to SC8280XP SoC
> scsi: ufs: ufs-qcom: Remove un-necessary goto statements
> scsi: ufs: ufs-qcom: Remove un-necessary WARN_ON()
> scsi: ufs: ufs-qcom: Use bitfields where appropriate
> scsi: ufs: ufs-qcom: Use dev_err_probe() for printing probe error
> scsi: ufs: ufs-qcom: Fix the Qcom register name for offset 0xD0
> scsi: ufs: core: Add reinit_notify() callback
> scsi: ufs: core: Add support for reinitializing the UFS device
> scsi: ufs: ufs-qcom: Factor out the logic finding the HS Gear
> scsi: ufs: ufs-qcom: Add support for reinitializing the UFS device
> scsi: ufs: ufs-qcom: Add support for finding max gear on new platforms
> MAINTAINERS: Add myself as the maintainer for Qcom UFS drivers
>
> MAINTAINERS | 8 +
> .../phy/qualcomm/phy-qcom-qmp-pcs-ufs-v5.h | 1 +
> drivers/phy/qualcomm/phy-qcom-qmp-ufs.c | 454 +++++++++++++-----
> drivers/ufs/core/ufshcd-priv.h | 6 +
> drivers/ufs/core/ufshcd.c | 63 ++-
> drivers/ufs/host/ufs-qcom.c | 170 +++----
> drivers/ufs/host/ufs-qcom.h | 70 +--
> include/ufs/ufshcd.h | 8 +
> 8 files changed, 532 insertions(+), 248 deletions(-)
>
> --
> 2.25.1
>