Re: [PATCH v2 6/6] arm64: dts: allwinner: h6: add Rongpin RP-H6C SoM and RP-H6B board

From: Samuel Holland
Date: Fri Dec 02 2022 - 21:11:52 EST

On 12/2/22 02:16, Icenowy Zheng wrote:
> Rongpin RP-H6C is an Allwinner H6 SoM by Rongpin, with Allwinner H6 SoC,
> AXP805 PMIC, LPDDR3 memory and eMMC storage on it.
>
> RP-H6B is their official evaluation board of RP-H6C, with an onboard
> GL850G USB hub, Ampak AP6212 Wi-Fi module and some circuits about LVDS
> display. It also exports the OTG USB port, the USB 3.0 port, PCIe bus
> (as mPCIe slot), internal Ethernet PHY, analog audio/video and HDMI
> port.
>
> Add a DTSI file for the SoM and a DTS for the full board.
>
> Signed-off-by: Icenowy Zheng <uwu@xxxxxxxxxx>
> ---
> Changes in v2:
> - Name all regulator nodes regulator-xxx.
> - Fixed underscores in node names.
>
> arch/arm64/boot/dts/allwinner/Makefile | 1 +
> .../boot/dts/allwinner/sun50i-h6-rp-h6b.dts | 239 ++++++++++++++++++
> .../boot/dts/allwinner/sun50i-h6-rp-h6c.dtsi | 180 +++++++++++++
> 3 files changed, 420 insertions(+)
> create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h6-rp-h6b.dts
> create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h6-rp-h6c.dtsi
>
> diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
> index 6a96494a2e0a..e289fedcac29 100644
> --- a/arch/arm64/boot/dts/allwinner/Makefile
> +++ b/arch/arm64/boot/dts/allwinner/Makefile
> @@ -36,6 +36,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-lite2.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-one-plus.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64-model-b.dtb
> +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-rp-h6b.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6-mini.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-rp-h6b.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-rp-h6b.dts
> new file mode 100644
> index 000000000000..d9994e9beb81
> --- /dev/null
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-rp-h6b.dts
> @@ -0,0 +1,239 @@
> +// SPDX-License-Identifier: (GPL-2.0+ or MIT)
> +/*
> + * Copyright (C) 2022 Icenowy Zheng <icenowy@xxxxxxx>
> + */
> +/dts-v1/;
> +
> +#include "sun50i-h6-rp-h6c.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +
> +/ {
> + model = "Rongpin RP-H6B baseboard";
> + compatible = "rongpin,rp-h6b", "rongpin,rp-h6c",
> + "allwinner,sun50i-h6";
> +
> + aliases {
> + ethernet0 = &emac;
> + serial0 = &uart0;
> + /*
> + * Prioritize the external RTC because it's powered
> + * by a cell battery.
> + */
> + rtc0 = &hym8563;
> + rtc1 = &rtc;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + hdmi_connector: connector {
> + compatible = "hdmi-connector";
> + type = "a";
> +
> + port {
> + hdmi_con_in: endpoint {
> + remote-endpoint = <&hdmi_out_con>;
> + };
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + led {
> + label = "rongpin:red:link";

Please use color and function properties instead.

> + gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>; /* PL3 */
> + /*
> + * On the schematics this LED is marked as "lit when
> + * powering on and blinking when running".
> + */
> + linux,default-trigger = "heartbeat";
> + };
> + };
> +
> + /*
> + * The VDD_5V power rail is connected to the internal regulator
> + * of GL850G, to power up the 3.3V core of it.
> + */
> + reg_v33_hub: regulator-v33-hub {
> + compatible = "regulator-fixed";
> + regulator-name = "v33-hub";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&reg_vdd_5v>;
> + };
> +
> + /*
> + * This board inputs 5V to AP6212 via a SS34 diode. Use this
> + * regulator as the model of the internal regulator of AP6212.
> + */
> + reg_vcc3v3_ap6212: regulator-vcc3v3-ap6212 {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc3v3-ap6212";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&reg_ps>;
> + };
> +
> + reg_vdd_5v: regulator-vdd-5v {
> + compatible = "regulator-fixed";
> + regulator-name = "vdd-5v";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + startup-delay-us = <100000>;
> + gpio = <&r_pio 0 5 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + vin-supply = <&reg_ps>;
> + };
> +
> + /* For mPCIe slot WWAN modules / PCIe cards */
> + reg_vdd_3g: regulator-vdd-3g {
> + compatible = "regulator-fixed";
> + regulator-name = "vdd-3g";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + startup-delay-us = <100000>;
> + gpio = <&r_pio 0 7 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + vin-supply = <&reg_ps>;
> + /*
> + * As a hack for lacking of control of a hub downstream
> + * port's Vbus.
> + */
> + regulator-always-on;
> + };
> +
> + wifi_pwrseq: wifi-pwrseq {
> + compatible = "mmc-pwrseq-simple";
> + reset-gpios = <&r_pio 1 3 GPIO_ACTIVE_LOW>; /* PM3 */
> + post-power-on-delay-ms = <200>;
> + };
> +};
> +
> +&de {
> + status = "okay";
> +};
> +
> +&ehci0 {
> + status = "okay";
> +};
> +
> +&ehci3 {
> + status = "okay";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + hub@1 {
> + /* Genesys Logic GL850G usb hub */
> + compatible = "usb5e3,608";
> + reg = <1>;
> + vdd-supply = <&reg_v33_hub>;
> + reset-gpios = <&pio 7 2 GPIO_ACTIVE_LOW>;
> + };
> +};
> +
> +&hdmi {
> + status = "okay";
> +};
> +
> +&hdmi_out {
> + hdmi_out_con: endpoint {
> + remote-endpoint = <&hdmi_con_in>;
> + };
> +};
> +
> +&i2c0 {
> + status = "okay";
> +
> + hym8563: rtc@51 {
> + compatible = "haoyu,hym8563";
> + reg = <0x51>;
> + #clock-cells = <0>;
> + };
> +};
> +
> +&mmc0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc0_pins>;
> + vmmc-supply = <&reg_cldo1>;
> + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
> + bus-width = <4>;
> + status = "okay";
> +};
> +
> +&mmc1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc1_pins>;
> + vmmc-supply = <&reg_vcc3v3_ap6212>;
> + vqmmc-supply = <&reg_bldo3>;
> + mmc-pwrseq = <&wifi_pwrseq>;
> + non-removable;
> + bus-width = <4>;
> + status = "okay";
> +
> + brcmf: wifi@1 {
> + reg = <1>;
> + compatible = "brcm,bcm4329-fmac";
> + interrupt-parent = <&r_pio>;
> + interrupts = <1 0 IRQ_TYPE_LEVEL_LOW>; /* PM0 */
> + interrupt-names = "host-wake";
> + };
> +};
> +
> +&ohci0 {
> + status = "okay";
> +};
> +
> +/* Converted from 12v with a fixed DC-DC on the baseboard */
> +&reg_ps {
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> +};
> +
> +&uart0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart0_ph_pins>;
> + status = "okay";
> +};
> +
> +/* Bluetooth */
> +&uart1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
> + uart-has-rtscts;
> + status = "okay";
> +
> + bluetooth {
> + compatible = "brcm,bcm43438-bt";
> + max-speed = <1500000>;
> + clocks = <&rtc CLK_OSC32K_FANOUT>;
> + clock-names = "lpo";
> + vbat-supply = <&reg_ps>;
> + vddio-supply = <&reg_bldo3>;
> + device-wakeup-gpios = <&r_pio 1 2 GPIO_ACTIVE_HIGH>; /* PM2 */
> + shutdown-gpios = <&r_pio 1 4 GPIO_ACTIVE_HIGH>; /* PM4 */
> + interrupt-parent = <&r_pio>;
> + interrupts = <1 1 IRQ_TYPE_EDGE_FALLING>; /* PM1 */
> + interrupt-names = "host-wakeup";
> + };
> +};
> +
> +&uart1_pins {
> + bias-pull-up;
> +};
> +
> +&uart1_rts_cts_pins {
> + bias-pull-up;
> +};
> +
> +&usb2otg {
> + dr_mode = "host";
> + status = "okay";
> +};
> +
> +&usb2phy {
> + usb0_vbus-supply = <&reg_vdd_5v>;
> + status = "okay";
> +};
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-rp-h6c.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h6-rp-h6c.dtsi
> new file mode 100644
> index 000000000000..637c194016c4
> --- /dev/null
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-rp-h6c.dtsi
> @@ -0,0 +1,180 @@
> +// SPDX-License-Identifier: (GPL-2.0+ or MIT)
> +/*
> + * Copyright (C) 2019-2022 Icenowy Zheng <icenowy@xxxxxxx>
> + */
> +
> +#include "sun50i-h6.dtsi"
> +#include "sun50i-h6-cpu-opp.dtsi"
> +#include "sun50i-h6-gpu-opp.dtsi"
> +
> +/ {
> + ext_osc32k: ext-osc32k-clk {
> + #clock-cells = <0>;
> + compatible = "fixed-clock";
> + clock-frequency = <32768>;
> + clock-output-names = "ext_osc32k";
> + };
> +
> + /* Marked 3.4v~5.5v on SoM schematics */
> + reg_ps: regulator-ps {
> + compatible = "regulator-fixed";
> + regulator-name = "ps";
> + };
> +};
> +
> +&cpu0 {
> + cpu-supply = <&reg_dcdca>;
> +};
> +
> +&gpu {
> + mali-supply = <&reg_dcdcc>;
> + status = "okay";
> +};
> +
> +&mmc2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc2_pins>;
> + vmmc-supply = <&reg_cldo1>;
> + vqmmc-supply = <&reg_bldo2>;
> + non-removable;
> + cap-mmc-hw-reset;
> + bus-width = <8>;
> + status = "okay";
> +};
> +
> +&pio {
> + vcc-pc-supply = <&reg_bldo2>;
> + vcc-pd-supply = <&reg_aldo2>;
> + vcc-pg-supply = <&reg_bldo3>;
> +};
> +
> +&r_pio {
> + /*
> + * FIXME: We can't add that supply for now since it would
> + * create a circular dependency between pinctrl, the regulator
> + * and the RSB Bus.
> + *
> + * vcc-pl-supply = <&reg_aldo1>;
> + */
> + vcc-pm-supply = <&reg_bldo3>;
> +};
> +
> +&r_rsb {
> + status = "okay";
> + clock-frequency = <400000>;
> +
> + axp805: pmic@745 {
> + compatible = "x-powers,axp805", "x-powers,axp806";
> + reg = <0x745>;
> + interrupt-parent = <&r_intc>;
> + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_LOW>;
> + interrupt-controller;
> + #interrupt-cells = <1>;
> + x-powers,self-working-mode;
> + vina-supply = <&reg_ps>;
> + vinb-supply = <&reg_ps>;
> + vinc-supply = <&reg_ps>;
> + vind-supply = <&reg_ps>;
> + vine-supply = <&reg_ps>;
> + aldoin-supply = <&reg_ps>;
> + bldoin-supply = <&reg_ps>;
> + cldoin-supply = <&reg_ps>;
> +
> + regulators {
> + reg_aldo1: aldo1 {
> + regulator-always-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc-pl";
> + };
> +
> + reg_aldo2: aldo2 {
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc-ac200";
> + regulator-enable-ramp-delay = <100000>;
> + };
> +
> + aldo3 {
> + /* unused */
> + };
> +
> + reg_bldo1: bldo1 {
> + regulator-always-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc-bias-pll";
> + };
> +
> + reg_bldo2: bldo2 {
> + regulator-always-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc-efuse-pcie-hdmi-io";
> + };
> +
> + reg_bldo3: bldo3 {
> + regulator-always-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc-dcxoio";
> + };
> +
> + bldo4 {
> + /* unused */
> + };
> +
> + reg_cldo1: cldo1 {
> + /* This regulator is connected with ALDO3 */

In this case, shouldn't ALDO3 have the same voltage constraints?

Other than these two minor issues:

Acked-by: Samuel Holland <samuel@xxxxxxxxxxxx>

> + regulator-always-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc-3v3-2";
> + };
> +
> + cldo2 {
> + /* unused */
> + };
> +
> + cldo3 {
> + /* unused */
> + };
> +
> + reg_dcdca: dcdca {
> + regulator-always-on;
> + regulator-min-microvolt = <810000>;
> + regulator-max-microvolt = <1160000>;
> + regulator-ramp-delay = <2500>;
> + regulator-name = "vdd-cpu";
> + };
> +
> + reg_dcdcc: dcdcc {
> + regulator-min-microvolt = <810000>;
> + regulator-max-microvolt = <1080000>;
> + regulator-name = "vdd-gpu";
> + };
> +
> + reg_dcdcd: dcdcd {
> + regulator-always-on;
> + regulator-min-microvolt = <960000>;
> + regulator-max-microvolt = <960000>;
> + regulator-name = "vdd-sys";
> + };
> +
> + reg_dcdce: dcdce {
> + regulator-always-on;
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-name = "vcc-dram";
> + };
> +
> + sw {
> + /* unused */
> + };
> + };
> + };
> +};
> +
> +&rtc {
> + clocks = <&ext_osc32k>;
> +};