[PATCH] [v2] ata: ahci: fix enum constants for gcc-13

From: Arnd Bergmann
Date: Sat Dec 03 2022 - 05:54:46 EST


From: Arnd Bergmann <arnd@xxxxxxxx>

gcc-13 slightly changes the type of constant expressions that are defined
in an enum, which triggers a compile time sanity check in libata:

linux/drivers/ata/libahci.c: In function 'ahci_led_store':
linux/include/linux/compiler_types.h:357:45: error: call to '__compiletime_assert_302' declared with attribute error: BUILD_BUG_ON failed: sizeof(_s) > sizeof(long)
357 | _compiletime_assert(condition, msg, __compiletime_assert_, __COUNTER__)

The new behavior is that sizeof() returns the same value for the
constant as it does for the enum type, which is generally more sensible
and consistent.

The problem in libata is that it contains a single enum definition for
lots of unrelated constants, some of which are large positive (unsigned)
integers like 0xffffffff, while others like (1<<31) are interpreted as
negative integers, and this forces the enum type to become 64 bit wide
even though most constants would still fit into a signed 32-bit 'int'.

Fix this by changing the entire enum definition to use BIT(x) in place
of (1<<x), which results in all values being seen as 'unsigned' and
fitting into an unsigned 32-bit type.

Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=107917
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=107405
Reported-by: Luis Machado <luis.machado@xxxxxxx>
Cc: linux-ide@xxxxxxxxxxxxxxx
Cc: Damien Le Moal <damien.lemoal@xxxxxxxxxxxxxxxxxx>
Cc: stable@xxxxxxxxxxxxxxx
Cc: Randy Dunlap <rdunlap@xxxxxxxxxxxxx>
Signed-off-by: Arnd Bergmann <arnd@xxxxxxxx>
---
Luis, I don't have gcc-13 installed on the machine I used for
creating this patch, can you give this a spin and see if it
addresses the build failure?

v2 changes:
- fix typos in changelog
- change PORT_CMD_ICC_* constants as well
- include linux/bits.h
---
drivers/ata/ahci.h | 245 +++++++++++++++++++++++----------------------
1 file changed, 123 insertions(+), 122 deletions(-)

diff --git a/drivers/ata/ahci.h b/drivers/ata/ahci.h
index 7add8e79912b..ff8e6ae1c636 100644
--- a/drivers/ata/ahci.h
+++ b/drivers/ata/ahci.h
@@ -24,6 +24,7 @@
#include <linux/libata.h>
#include <linux/phy/phy.h>
#include <linux/regulator/consumer.h>
+#include <linux/bits.h>

/* Enclosure Management Control */
#define EM_CTRL_MSG_TYPE 0x000f0000
@@ -53,12 +54,12 @@ enum {
AHCI_PORT_PRIV_FBS_DMA_SZ = AHCI_CMD_SLOT_SZ +
AHCI_CMD_TBL_AR_SZ +
(AHCI_RX_FIS_SZ * 16),
- AHCI_IRQ_ON_SG = (1 << 31),
- AHCI_CMD_ATAPI = (1 << 5),
- AHCI_CMD_WRITE = (1 << 6),
- AHCI_CMD_PREFETCH = (1 << 7),
- AHCI_CMD_RESET = (1 << 8),
- AHCI_CMD_CLR_BUSY = (1 << 10),
+ AHCI_IRQ_ON_SG = BIT(31),
+ AHCI_CMD_ATAPI = BIT(5),
+ AHCI_CMD_WRITE = BIT(6),
+ AHCI_CMD_PREFETCH = BIT(7),
+ AHCI_CMD_RESET = BIT(8),
+ AHCI_CMD_CLR_BUSY = BIT(10),

RX_FIS_PIO_SETUP = 0x20, /* offset of PIO Setup FIS data */
RX_FIS_D2H_REG = 0x40, /* offset of D2H Register FIS data */
@@ -76,37 +77,37 @@ enum {
HOST_CAP2 = 0x24, /* host capabilities, extended */

/* HOST_CTL bits */
- HOST_RESET = (1 << 0), /* reset controller; self-clear */
- HOST_IRQ_EN = (1 << 1), /* global IRQ enable */
- HOST_MRSM = (1 << 2), /* MSI Revert to Single Message */
- HOST_AHCI_EN = (1 << 31), /* AHCI enabled */
+ HOST_RESET = BIT(0), /* reset controller; self-clear */
+ HOST_IRQ_EN = BIT(1), /* global IRQ enable */
+ HOST_MRSM = BIT(2), /* MSI Revert to Single Message */
+ HOST_AHCI_EN = BIT(31), /* AHCI enabled */

/* HOST_CAP bits */
- HOST_CAP_SXS = (1 << 5), /* Supports External SATA */
- HOST_CAP_EMS = (1 << 6), /* Enclosure Management support */
- HOST_CAP_CCC = (1 << 7), /* Command Completion Coalescing */
- HOST_CAP_PART = (1 << 13), /* Partial state capable */
- HOST_CAP_SSC = (1 << 14), /* Slumber state capable */
- HOST_CAP_PIO_MULTI = (1 << 15), /* PIO multiple DRQ support */
- HOST_CAP_FBS = (1 << 16), /* FIS-based switching support */
- HOST_CAP_PMP = (1 << 17), /* Port Multiplier support */
- HOST_CAP_ONLY = (1 << 18), /* Supports AHCI mode only */
- HOST_CAP_CLO = (1 << 24), /* Command List Override support */
- HOST_CAP_LED = (1 << 25), /* Supports activity LED */
- HOST_CAP_ALPM = (1 << 26), /* Aggressive Link PM support */
- HOST_CAP_SSS = (1 << 27), /* Staggered Spin-up */
- HOST_CAP_MPS = (1 << 28), /* Mechanical presence switch */
- HOST_CAP_SNTF = (1 << 29), /* SNotification register */
- HOST_CAP_NCQ = (1 << 30), /* Native Command Queueing */
- HOST_CAP_64 = (1 << 31), /* PCI DAC (64-bit DMA) support */
+ HOST_CAP_SXS = BIT(5), /* Supports External SATA */
+ HOST_CAP_EMS = BIT(6), /* Enclosure Management support */
+ HOST_CAP_CCC = BIT(7), /* Command Completion Coalescing */
+ HOST_CAP_PART = BIT(13), /* Partial state capable */
+ HOST_CAP_SSC = BIT(14), /* Slumber state capable */
+ HOST_CAP_PIO_MULTI = BIT(15), /* PIO multiple DRQ support */
+ HOST_CAP_FBS = BIT(16), /* FIS-based switching support */
+ HOST_CAP_PMP = BIT(17), /* Port Multiplier support */
+ HOST_CAP_ONLY = BIT(18), /* Supports AHCI mode only */
+ HOST_CAP_CLO = BIT(24), /* Command List Override support */
+ HOST_CAP_LED = BIT(25), /* Supports activity LED */
+ HOST_CAP_ALPM = BIT(26), /* Aggressive Link PM support */
+ HOST_CAP_SSS = BIT(27), /* Staggered Spin-up */
+ HOST_CAP_MPS = BIT(28), /* Mechanical presence switch */
+ HOST_CAP_SNTF = BIT(29), /* SNotification register */
+ HOST_CAP_NCQ = BIT(30), /* Native Command Queueing */
+ HOST_CAP_64 = BIT(31), /* PCI DAC (64-bit DMA) support */

/* HOST_CAP2 bits */
- HOST_CAP2_BOH = (1 << 0), /* BIOS/OS handoff supported */
- HOST_CAP2_NVMHCI = (1 << 1), /* NVMHCI supported */
- HOST_CAP2_APST = (1 << 2), /* Automatic partial to slumber */
- HOST_CAP2_SDS = (1 << 3), /* Support device sleep */
- HOST_CAP2_SADM = (1 << 4), /* Support aggressive DevSlp */
- HOST_CAP2_DESO = (1 << 5), /* DevSlp from slumber only */
+ HOST_CAP2_BOH = BIT(0), /* BIOS/OS handoff supported */
+ HOST_CAP2_NVMHCI = BIT(1), /* NVMHCI supported */
+ HOST_CAP2_APST = BIT(2), /* Automatic partial to slumber */
+ HOST_CAP2_SDS = BIT(3), /* Support device sleep */
+ HOST_CAP2_SADM = BIT(4), /* Support aggressive DevSlp */
+ HOST_CAP2_DESO = BIT(5), /* DevSlp from slumber only */

/* registers for each SATA port */
PORT_LST_ADDR = 0x00, /* command list DMA addr */
@@ -128,24 +129,24 @@ enum {
PORT_DEVSLP = 0x44, /* device sleep */

/* PORT_IRQ_{STAT,MASK} bits */
- PORT_IRQ_COLD_PRES = (1 << 31), /* cold presence detect */
- PORT_IRQ_TF_ERR = (1 << 30), /* task file error */
- PORT_IRQ_HBUS_ERR = (1 << 29), /* host bus fatal error */
- PORT_IRQ_HBUS_DATA_ERR = (1 << 28), /* host bus data error */
- PORT_IRQ_IF_ERR = (1 << 27), /* interface fatal error */
- PORT_IRQ_IF_NONFATAL = (1 << 26), /* interface non-fatal error */
- PORT_IRQ_OVERFLOW = (1 << 24), /* xfer exhausted available S/G */
- PORT_IRQ_BAD_PMP = (1 << 23), /* incorrect port multiplier */
-
- PORT_IRQ_PHYRDY = (1 << 22), /* PhyRdy changed */
- PORT_IRQ_DMPS = (1 << 7), /* mechanical presence status */
- PORT_IRQ_CONNECT = (1 << 6), /* port connect change status */
- PORT_IRQ_SG_DONE = (1 << 5), /* descriptor processed */
- PORT_IRQ_UNK_FIS = (1 << 4), /* unknown FIS rx'd */
- PORT_IRQ_SDB_FIS = (1 << 3), /* Set Device Bits FIS rx'd */
- PORT_IRQ_DMAS_FIS = (1 << 2), /* DMA Setup FIS rx'd */
- PORT_IRQ_PIOS_FIS = (1 << 1), /* PIO Setup FIS rx'd */
- PORT_IRQ_D2H_REG_FIS = (1 << 0), /* D2H Register FIS rx'd */
+ PORT_IRQ_COLD_PRES = BIT(31), /* cold presence detect */
+ PORT_IRQ_TF_ERR = BIT(30), /* task file error */
+ PORT_IRQ_HBUS_ERR = BIT(29), /* host bus fatal error */
+ PORT_IRQ_HBUS_DATA_ERR = BIT(28), /* host bus data error */
+ PORT_IRQ_IF_ERR = BIT(27), /* interface fatal error */
+ PORT_IRQ_IF_NONFATAL = BIT(26), /* interface non-fatal error */
+ PORT_IRQ_OVERFLOW = BIT(24), /* xfer exhausted available S/G */
+ PORT_IRQ_BAD_PMP = BIT(23), /* incorrect port multiplier */
+
+ PORT_IRQ_PHYRDY = BIT(22), /* PhyRdy changed */
+ PORT_IRQ_DMPS = BIT(7), /* mechanical presence status */
+ PORT_IRQ_CONNECT = BIT(6), /* port connect change status */
+ PORT_IRQ_SG_DONE = BIT(5), /* descriptor processed */
+ PORT_IRQ_UNK_FIS = BIT(4), /* unknown FIS rx'd */
+ PORT_IRQ_SDB_FIS = BIT(3), /* Set Device Bits FIS rx'd */
+ PORT_IRQ_DMAS_FIS = BIT(2), /* DMA Setup FIS rx'd */
+ PORT_IRQ_PIOS_FIS = BIT(1), /* PIO Setup FIS rx'd */
+ PORT_IRQ_D2H_REG_FIS = BIT(0), /* D2H Register FIS rx'd */

PORT_IRQ_FREEZE = PORT_IRQ_HBUS_ERR |
PORT_IRQ_IF_ERR |
@@ -161,27 +162,27 @@ enum {
PORT_IRQ_PIOS_FIS | PORT_IRQ_D2H_REG_FIS,

/* PORT_CMD bits */
- PORT_CMD_ASP = (1 << 27), /* Aggressive Slumber/Partial */
- PORT_CMD_ALPE = (1 << 26), /* Aggressive Link PM enable */
- PORT_CMD_ATAPI = (1 << 24), /* Device is ATAPI */
- PORT_CMD_FBSCP = (1 << 22), /* FBS Capable Port */
- PORT_CMD_ESP = (1 << 21), /* External Sata Port */
- PORT_CMD_CPD = (1 << 20), /* Cold Presence Detection */
- PORT_CMD_MPSP = (1 << 19), /* Mechanical Presence Switch */
- PORT_CMD_HPCP = (1 << 18), /* HotPlug Capable Port */
- PORT_CMD_PMP = (1 << 17), /* PMP attached */
- PORT_CMD_LIST_ON = (1 << 15), /* cmd list DMA engine running */
- PORT_CMD_FIS_ON = (1 << 14), /* FIS DMA engine running */
- PORT_CMD_FIS_RX = (1 << 4), /* Enable FIS receive DMA engine */
- PORT_CMD_CLO = (1 << 3), /* Command list override */
- PORT_CMD_POWER_ON = (1 << 2), /* Power up device */
- PORT_CMD_SPIN_UP = (1 << 1), /* Spin up device */
- PORT_CMD_START = (1 << 0), /* Enable port DMA engine */
-
- PORT_CMD_ICC_MASK = (0xf << 28), /* i/f ICC state mask */
- PORT_CMD_ICC_ACTIVE = (0x1 << 28), /* Put i/f in active state */
- PORT_CMD_ICC_PARTIAL = (0x2 << 28), /* Put i/f in partial state */
- PORT_CMD_ICC_SLUMBER = (0x6 << 28), /* Put i/f in slumber state */
+ PORT_CMD_ASP = BIT(27), /* Aggressive Slumber/Partial */
+ PORT_CMD_ALPE = BIT(26), /* Aggressive Link PM enable */
+ PORT_CMD_ATAPI = BIT(24), /* Device is ATAPI */
+ PORT_CMD_FBSCP = BIT(22), /* FBS Capable Port */
+ PORT_CMD_ESP = BIT(21), /* External Sata Port */
+ PORT_CMD_CPD = BIT(20), /* Cold Presence Detection */
+ PORT_CMD_MPSP = BIT(19), /* Mechanical Presence Switch */
+ PORT_CMD_HPCP = BIT(18), /* HotPlug Capable Port */
+ PORT_CMD_PMP = BIT(17), /* PMP attached */
+ PORT_CMD_LIST_ON = BIT(15), /* cmd list DMA engine running */
+ PORT_CMD_FIS_ON = BIT(14), /* FIS DMA engine running */
+ PORT_CMD_FIS_RX = BIT(4), /* Enable FIS receive DMA engine */
+ PORT_CMD_CLO = BIT(3), /* Command list override */
+ PORT_CMD_POWER_ON = BIT(2), /* Power up device */
+ PORT_CMD_SPIN_UP = BIT(1), /* Spin up device */
+ PORT_CMD_START = BIT(0), /* Enable port DMA engine */
+
+ PORT_CMD_ICC_MASK = (0xfu << 28), /* i/f ICC state mask */
+ PORT_CMD_ICC_ACTIVE = (0x1u << 28), /* Put i/f in active state */
+ PORT_CMD_ICC_PARTIAL = (0x2u << 28), /* Put i/f in partial state */
+ PORT_CMD_ICC_SLUMBER = (0x6u << 28), /* Put i/f in slumber state */

/* PORT_CMD capabilities mask */
PORT_CMD_CAP = PORT_CMD_HPCP | PORT_CMD_MPSP |
@@ -192,9 +193,9 @@ enum {
PORT_FBS_ADO_OFFSET = 12, /* FBS active dev optimization offset */
PORT_FBS_DEV_OFFSET = 8, /* FBS device to issue offset */
PORT_FBS_DEV_MASK = (0xf << PORT_FBS_DEV_OFFSET), /* FBS.DEV */
- PORT_FBS_SDE = (1 << 2), /* FBS single device error */
- PORT_FBS_DEC = (1 << 1), /* FBS device error clear */
- PORT_FBS_EN = (1 << 0), /* Enable FBS */
+ PORT_FBS_SDE = BIT(2), /* FBS single device error */
+ PORT_FBS_DEC = BIT(1), /* FBS device error clear */
+ PORT_FBS_EN = BIT(0), /* Enable FBS */

/* PORT_DEVSLP bits */
PORT_DEVSLP_DM_OFFSET = 25, /* DITO multiplier offset */
@@ -202,50 +203,50 @@ enum {
PORT_DEVSLP_DITO_OFFSET = 15, /* DITO offset */
PORT_DEVSLP_MDAT_OFFSET = 10, /* Minimum assertion time */
PORT_DEVSLP_DETO_OFFSET = 2, /* DevSlp exit timeout */
- PORT_DEVSLP_DSP = (1 << 1), /* DevSlp present */
- PORT_DEVSLP_ADSE = (1 << 0), /* Aggressive DevSlp enable */
+ PORT_DEVSLP_DSP = BIT(1), /* DevSlp present */
+ PORT_DEVSLP_ADSE = BIT(0), /* Aggressive DevSlp enable */

/* hpriv->flags bits */

#define AHCI_HFLAGS(flags) .private_data = (void *)(flags)

- AHCI_HFLAG_NO_NCQ = (1 << 0),
- AHCI_HFLAG_IGN_IRQ_IF_ERR = (1 << 1), /* ignore IRQ_IF_ERR */
- AHCI_HFLAG_IGN_SERR_INTERNAL = (1 << 2), /* ignore SERR_INTERNAL */
- AHCI_HFLAG_32BIT_ONLY = (1 << 3), /* force 32bit */
- AHCI_HFLAG_MV_PATA = (1 << 4), /* PATA port */
- AHCI_HFLAG_NO_MSI = (1 << 5), /* no PCI MSI */
- AHCI_HFLAG_NO_PMP = (1 << 6), /* no PMP */
- AHCI_HFLAG_SECT255 = (1 << 8), /* max 255 sectors */
- AHCI_HFLAG_YES_NCQ = (1 << 9), /* force NCQ cap on */
- AHCI_HFLAG_NO_SUSPEND = (1 << 10), /* don't suspend */
- AHCI_HFLAG_SRST_TOUT_IS_OFFLINE = (1 << 11), /* treat SRST timeout as
- link offline */
- AHCI_HFLAG_NO_SNTF = (1 << 12), /* no sntf */
- AHCI_HFLAG_NO_FPDMA_AA = (1 << 13), /* no FPDMA AA */
- AHCI_HFLAG_YES_FBS = (1 << 14), /* force FBS cap on */
- AHCI_HFLAG_DELAY_ENGINE = (1 << 15), /* do not start engine on
- port start (wait until
- error-handling stage) */
- AHCI_HFLAG_NO_DEVSLP = (1 << 17), /* no device sleep */
- AHCI_HFLAG_NO_FBS = (1 << 18), /* no FBS */
+ AHCI_HFLAG_NO_NCQ = BIT(0),
+ AHCI_HFLAG_IGN_IRQ_IF_ERR = BIT(1), /* ignore IRQ_IF_ERR */
+ AHCI_HFLAG_IGN_SERR_INTERNAL = BIT(2), /* ignore SERR_INTERNAL */
+ AHCI_HFLAG_32BIT_ONLY = BIT(3), /* force 32bit */
+ AHCI_HFLAG_MV_PATA = BIT(4), /* PATA port */
+ AHCI_HFLAG_NO_MSI = BIT(5), /* no PCI MSI */
+ AHCI_HFLAG_NO_PMP = BIT(6), /* no PMP */
+ AHCI_HFLAG_SECT255 = BIT(8), /* max 255 sectors */
+ AHCI_HFLAG_YES_NCQ = BIT(9), /* force NCQ cap on */
+ AHCI_HFLAG_NO_SUSPEND = BIT(10), /* don't suspend */
+ AHCI_HFLAG_SRST_TOUT_IS_OFFLINE = BIT(11), /* treat SRST timeout as
+ link offline */
+ AHCI_HFLAG_NO_SNTF = BIT(12), /* no sntf */
+ AHCI_HFLAG_NO_FPDMA_AA = BIT(13), /* no FPDMA AA */
+ AHCI_HFLAG_YES_FBS = BIT(14), /* force FBS cap on */
+ AHCI_HFLAG_DELAY_ENGINE = BIT(15), /* do not start engine on
+ port start (wait until
+ error-handling stage) */
+ AHCI_HFLAG_NO_DEVSLP = BIT(17), /* no device sleep */
+ AHCI_HFLAG_NO_FBS = BIT(18), /* no FBS */

#ifdef CONFIG_PCI_MSI
- AHCI_HFLAG_MULTI_MSI = (1 << 20), /* per-port MSI(-X) */
+ AHCI_HFLAG_MULTI_MSI = BIT(20), /* per-port MSI(-X) */
#else
/* compile out MSI infrastructure */
AHCI_HFLAG_MULTI_MSI = 0,
#endif
- AHCI_HFLAG_WAKE_BEFORE_STOP = (1 << 22), /* wake before DMA stop */
- AHCI_HFLAG_YES_ALPM = (1 << 23), /* force ALPM cap on */
- AHCI_HFLAG_NO_WRITE_TO_RO = (1 << 24), /* don't write to read
- only registers */
- AHCI_HFLAG_USE_LPM_POLICY = (1 << 25), /* chipset that should use
- SATA_MOBILE_LPM_POLICY
- as default lpm_policy */
- AHCI_HFLAG_SUSPEND_PHYS = (1 << 26), /* handle PHYs during
- suspend/resume */
- AHCI_HFLAG_NO_SXS = (1 << 28), /* SXS not supported */
+ AHCI_HFLAG_WAKE_BEFORE_STOP = BIT(22), /* wake before DMA stop */
+ AHCI_HFLAG_YES_ALPM = BIT(23), /* force ALPM cap on */
+ AHCI_HFLAG_NO_WRITE_TO_RO = BIT(24), /* don't write to read
+ only registers */
+ AHCI_HFLAG_USE_LPM_POLICY = BIT(25), /* chipset that should use
+ SATA_MOBILE_LPM_POLICY
+ as default lpm_policy */
+ AHCI_HFLAG_SUSPEND_PHYS = BIT(26), /* handle PHYs during
+ suspend/resume */
+ AHCI_HFLAG_NO_SXS = BIT(28), /* SXS not supported */

/* ap->flags bits */

@@ -261,22 +262,22 @@ enum {
EM_MAX_RETRY = 5,

/* em_ctl bits */
- EM_CTL_RST = (1 << 9), /* Reset */
- EM_CTL_TM = (1 << 8), /* Transmit Message */
- EM_CTL_MR = (1 << 0), /* Message Received */
- EM_CTL_ALHD = (1 << 26), /* Activity LED */
- EM_CTL_XMT = (1 << 25), /* Transmit Only */
- EM_CTL_SMB = (1 << 24), /* Single Message Buffer */
- EM_CTL_SGPIO = (1 << 19), /* SGPIO messages supported */
- EM_CTL_SES = (1 << 18), /* SES-2 messages supported */
- EM_CTL_SAFTE = (1 << 17), /* SAF-TE messages supported */
- EM_CTL_LED = (1 << 16), /* LED messages supported */
+ EM_CTL_RST = BIT(9), /* Reset */
+ EM_CTL_TM = BIT(8), /* Transmit Message */
+ EM_CTL_MR = BIT(0), /* Message Received */
+ EM_CTL_ALHD = BIT(26), /* Activity LED */
+ EM_CTL_XMT = BIT(25), /* Transmit Only */
+ EM_CTL_SMB = BIT(24), /* Single Message Buffer */
+ EM_CTL_SGPIO = BIT(19), /* SGPIO messages supported */
+ EM_CTL_SES = BIT(18), /* SES-2 messages supported */
+ EM_CTL_SAFTE = BIT(17), /* SAF-TE messages supported */
+ EM_CTL_LED = BIT(16), /* LED messages supported */

/* em message type */
- EM_MSG_TYPE_LED = (1 << 0), /* LED */
- EM_MSG_TYPE_SAFTE = (1 << 1), /* SAF-TE */
- EM_MSG_TYPE_SES2 = (1 << 2), /* SES-2 */
- EM_MSG_TYPE_SGPIO = (1 << 3), /* SGPIO */
+ EM_MSG_TYPE_LED = BIT(0), /* LED */
+ EM_MSG_TYPE_SAFTE = BIT(1), /* SAF-TE */
+ EM_MSG_TYPE_SES2 = BIT(2), /* SES-2 */
+ EM_MSG_TYPE_SGPIO = BIT(3), /* SGPIO */
};

struct ahci_cmd_hdr {
--
2.35.1