Re: [PATCH 5/5] dmaengine: ti: k3-udma: Add support for BCDMA CSI RX

[Péter Ujfalusi]

On 12/6/22 06:35, Vignesh Raghavendra wrote:
> BCDMA CSI RX present on AM62Ax SoC is a dedicated DMA for servicing
> Camera Serial Interface (CSI) IP. Add support for the same.
> 
> Signed-off-by: Vignesh Raghavendra <vigneshr@xxxxxx>
> ---
>  drivers/dma/ti/k3-udma.c | 37 ++++++++++++++++++++++++++++++++-----
>  1 file changed, 32 insertions(+), 5 deletions(-)
> 
> diff --git a/drivers/dma/ti/k3-udma.c b/drivers/dma/ti/k3-udma.c
> index 19fce52a9b53..a8b497ed3f30 100644
> --- a/drivers/dma/ti/k3-udma.c
> +++ b/drivers/dma/ti/k3-udma.c
> @@ -135,6 +135,7 @@ struct udma_match_data {
>  	u32 flags;
>  	u32 statictr_z_mask;
>  	u8 burst_size[3];
> +	struct udma_soc_data *soc_data;
>  };
>  
>  struct udma_soc_data {
> @@ -4295,6 +4296,25 @@ static struct udma_match_data j721e_mcu_data = {
>  	},
>  };
>  
> +static struct udma_soc_data am62a_dmss_csi_soc_data = {
> +	.oes = {
> +		.bcdma_rchan_data = 0xe00,
> +		.bcdma_rchan_ring = 0x1000,
> +	},
> +};
> +
> +static struct udma_match_data am62a_bcdma_csirx_data = {
> +	.type = DMA_TYPE_BCDMA,
> +	.psil_base = 0x3100,
> +	.enable_memcpy_support = false,
> +	.burst_size = {
> +		TI_SCI_RM_UDMAP_CHAN_BURST_SIZE_64_BYTES, /* Normal Channels */
> +		0, /* No H Channels */
> +		0, /* No UH Channels */
> +	},
> +	.soc_data = &am62a_dmss_csi_soc_data,
> +};
> +
>  static struct udma_match_data am64_bcdma_data = {
>  	.type = DMA_TYPE_BCDMA,
>  	.psil_base = 0x2000, /* for tchan and rchan, not applicable to bchan */
> @@ -4344,6 +4364,10 @@ static const struct of_device_id udma_of_match[] = {
>  		.compatible = "ti,am64-dmss-pktdma",
>  		.data = &am64_pktdma_data,
>  	},
> +	{
> +		.compatible = "ti,am62a-dmss-bcdma-csirx",
> +		.data = &am62a_bcdma_csirx_data,
> +	},
>  	{ /* Sentinel */ },
>  };
>  
> @@ -5272,12 +5296,15 @@ static int udma_probe(struct platform_device *pdev)
>  	}
>  	ud->match_data = match->data;
>  
> -	soc = soc_device_match(k3_soc_devices);
> -	if (!soc) {
> -		dev_err(dev, "No compatible SoC found\n");
> -		return -ENODEV;
> +	ud->soc_data = ud->match_data->soc_data;
> +	if (!ud->soc_data) {
> +		soc = soc_device_match(k3_soc_devices);
> +		if (!soc) {
> +			dev_err(dev, "No compatible SoC found\n");
> +			return -ENODEV;
> +		}
> +		ud->soc_data = soc->data;
>  	}
> -	ud->soc_data = soc->data;

Right, the original design was based on the promise that a DMSS will
contain maximum 1 BCDMA and/or 1 PKTDMA, looks like now a DMSS have 2
BCDMAs?

The only possible issue I can see is that if in future SoCs the Output
Event Offsets got shuffled for the BCDMAs, but then a new compatible for
each SoC might just work.

Nice solution with minimal change! ;)

>  
>  	ret = udma_get_mmrs(pdev, ud);
>  	if (ret)

-- 
Péter