[PATCH v2 6/7] arm64: dts: qcom: sa8540p-ride: add i2c nodes

[Brian Masney]

Add the necessary nodes in order to get i2c0, i2c1, i2c12, i2c15, and
i2c18 functioning on the automotive board and exposed to userspace.

This work was derived from various patches that Qualcomm delivered
to Red Hat in a downstream kernel. This change was validated by using
i2c-tools 4.3.3 on CentOS Stream 9:

[root@localhost ~]# i2cdetect -l
i2c-0  i2c             Geni-I2C                                I2C adapter
i2c-1  i2c             Geni-I2C                                I2C adapter
i2c-12 i2c             Geni-I2C                                I2C adapter
i2c-15 i2c             Geni-I2C                                I2C adapter
i2c-18 i2c             Geni-I2C                                I2C adapter

[root@localhost ~]# i2cdetect -a -y 15
Warning: Can't use SMBus Quick Write command, will skip some addresses
     0  1  2  3  4  5  6  7  8  9  a  b  c  d  e  f
00:
10:
20:
30: -- -- -- -- -- -- -- --
40:
50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
60:
70:

Signed-off-by: Brian Masney <bmasney@xxxxxxxxxx>
---
Changes since v1:
- Dropped qupX_ prefix from labels. (Johan)
- Reordered nodes based on new name.
- Added i2c buses 0, 1, and 12 (Shazad)
- Drop mux/config-pins and have the pin properties live directly
  under the i2cX-default-state node. (Konrad)
- Use decimal notation for drive strength (Johan)

A few things to note with this series applied on top of linux-next:
- Reading from i2c-0 using 'i2cdetect -y -a 0' gives the following error
  when reading from the ranges 0x30-0x37 and 0x50-0x5F.
      geni_i2c 980000.i2c: Timeout abort_m_cmd
- i2c-1 and i2c-2 successfully read using i2cdetect, however it takes
  several seconds.
- i2cdetect runs fast within a small fraction of a second for i2c-15
  and i2c18.
- 'i2cdetect -y -a $BUSNUM' shows the same address ranges 0x30-0x37
  and 0x50-0x5F in use on all 5 buses.

 arch/arm64/boot/dts/qcom/sa8540p-ride.dts | 83 +++++++++++++++++++++++
 1 file changed, 83 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sa8540p-ride.dts b/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
index b6e0db5508c7..ccd2ea3c9d04 100644
--- a/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
+++ b/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
@@ -17,6 +17,11 @@ / {
 	compatible = "qcom,sa8540p-ride", "qcom,sa8540p";
 
 	aliases {
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		i2c12 = &i2c12;
+		i2c15 = &i2c15;
+		i2c18 = &i2c18;
 		serial0 = &uart17;
 	};
 
@@ -146,6 +151,41 @@ vreg_l8g: ldo8 {
 	};
 };
 
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_default>;
+
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_default>;
+
+	status = "okay";
+};
+
+&i2c12 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c12_default>;
+
+	status = "okay";
+};
+
+&i2c15 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c15_default>;
+
+	status = "okay";
+};
+
+&i2c18 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c18_default>;
+
+	status = "okay";
+};
+
 &pcie2a {
 	ranges = <0x01000000 0x0 0x3c200000 0x0 0x3c200000 0x0 0x100000>,
 		 <0x02000000 0x0 0x3c300000 0x0 0x3c300000 0x0 0x1d00000>,
@@ -188,6 +228,14 @@ &pcie3a_phy {
 	status = "okay";
 };
 
+&qup0 {
+	status = "okay";
+};
+
+&qup1 {
+	status = "okay";
+};
+
 &qup2 {
 	status = "okay";
 };
@@ -268,6 +316,41 @@ &xo_board_clk {
 /* PINCTRL */
 
 &tlmm {
+	i2c0_default: i2c0-default-state {
+		pins = "gpio135", "gpio136";
+		function = "qup15";
+		drive-strength = <2>;
+		bias-pull-up;
+	};
+
+	i2c1_default: i2c1-default-state {
+		pins = "gpio158", "gpio159";
+		function = "qup15";
+		drive-strength = <2>;
+		bias-pull-up;
+	};
+
+	i2c12_default: i2c12-default-state {
+		pins = "gpio0", "gpio1";
+		function = "qup15";
+		drive-strength = <2>;
+		bias-pull-up;
+	};
+
+	i2c15_default: i2c15-default-state {
+		pins = "gpio36", "gpio37";
+		function = "qup15";
+		drive-strength = <2>;
+		bias-pull-up;
+	};
+
+	i2c18_default: i2c18-default-state {
+		pins = "gpio66", "gpio67";
+		function = "qup18";
+		drive-strength = <2>;
+		bias-pull-up;
+	};
+
 	pcie2a_default: pcie2a-default-state {
 		perst-pins {
 			pins = "gpio143";
-- 
2.38.1