Re: [PATCH] net: Fix for packets being rejected in the xHCI controller's ring buffer

[Seija K.]

Ok, thanks.

On Wed, Dec 14, 2022 at 10:25 AM Daniele Palmas <dnlplm@xxxxxxxxx> wrote:
>
> Hello Seija,
>
> Il giorno mar 13 dic 2022 alle ore 20:55 Seija K.
> <doremylover123@xxxxxxxxx> ha scritto:
> > On Tue, Dec 13, 2022 at 1:23 PM Daniele Palmas <dnlplm@xxxxxxxxx> wrote:
> > >
> > > Did you test this change with QMAP?
> > >
> > > To support qmap dl aggregated blocks qmi_wwan relies on the
> > > usbnet_change_mtu behavior of changing the rx_urb_size.
> > >
> > > Thanks,
> > > Daniele
> >
> > Yes, I did.
> >
>
> I've applied your change and verified that the rx_urb_size can't be
> changed anymore by modifying the mtu of the wwan netdevice and stays
> fixed to 1504.
>
> Just a heads-up, that this change is not working fine with qmap setup
> procedure, since the URB size can't be changed anymore to the value of
> the maximum dl aggregated block set through wda_set_data_format.
>
> I know that linking MTU with the rx_urb_size is odd, but this is how
> it's done currently.
>
> Regards,
> Daniele
>
> > On Tue, Dec 13, 2022 at 1:23 PM Daniele Palmas <dnlplm@xxxxxxxxx> wrote:
> > >
> > > Hello Seija,
> > >
> > > Il giorno mar 13 dic 2022 alle ore 18:44 Seija K.
> > > <doremylover123@xxxxxxxxx> ha scritto:
> > > >
> > > > When a packet larger than MTU arrives in Linux from the modem, it is
> > > > discarded with -EOVERFLOW error (Babble error).
> > > >
> > > > This is seen on USB3.0 and USB2.0 buses.
> > > >
> > > > This is because the MRU (Max Receive Size) is not a separate entity
> > > > from the MTU (Max Transmit Size), and the received packets can be
> > > > larger than those transmitted.
> > > >
> > > > Following the babble error, there was an endless supply of zero-length
> > > > URBs that were rejected with -EPROTO (increasing the rx input error
> > > > counter each time).
> > > >
> > > > This is only seen on USB3.0. These continue to come ad infinitum until
> > > > the modem is shut down.
> > > >
> > > > There appears to be a bug in the core USB handling code in Linux that
> > > > doesn't deal with network MTUs smaller than 1500 bytes well.
> > > >
> > > > By default, the dev->hard_mtu (the real MTU) is in lockstep with
> > > > dev->rx_urb_size (essentially an MRU), and the latter is causing
> > > > trouble.
> > > >
> > > > This has nothing to do with the modems; the issue can be reproduced by
> > > > getting a USB-Ethernet dongle, setting the MTU to 1430, and pinging
> > > > with size greater than 1406.
> > > >
> > > > Signed-off-by: Seija Kijin <doremylover123@xxxxxxxxx>
> > > >
> > > > Co-Authored-By: TarAldarion <gildeap@xxxxxx>
> > > > ---
> > > > drivers/net/usb/qmi_wwan.c | 7 +++++++
> > > > 1 file changed, 7 insertions(+)
> > > >
> > > > diff --git a/drivers/net/usb/qmi_wwan.c b/drivers/net/usb/qmi_wwan.c
> > > > index 554d4e2a84a4..39db53a74b5a 100644
> > > > --- a/drivers/net/usb/qmi_wwan.c
> > > > +++ b/drivers/net/usb/qmi_wwan.c
> > > > @@ -842,6 +842,13 @@ static int qmi_wwan_bind(struct usbnet *dev,
> > > > struct usb_interface *intf)
> > > > }
> > > > dev->net->netdev_ops = &qmi_wwan_netdev_ops;
> > > > dev->net->sysfs_groups[0] = &qmi_wwan_sysfs_attr_group;
> > > > + /* LTE Networks don't always respect their own MTU on the receiving side;
> > > > + * e.g. AT&T pushes 1430 MTU but still allows 1500 byte packets from
> > > > + * far-end networks. Make the receive buffer large enough to accommodate
> > > > + * them, and add four bytes so MTU does not equal MRU on network
> > > > + * with 1500 MTU. Otherwise, usbnet_change_mtu() will change both.
> > > > + */
> > > > + dev->rx_urb_size = ETH_DATA_LEN + 4;
> > >
> > > Did you test this change with QMAP?
> > >
> > > To support qmap dl aggregated blocks qmi_wwan relies on the
> > > usbnet_change_mtu behavior of changing the rx_urb_size.
> > >
> > > Thanks,
> > > Daniele
> > >
> > > > err:
> > > > return status;
> > > > }
> > > > --
> > > > 2.38.2