[PATCH v8 03/10] arm64: dts: qcom: Add pm8010 pmic dtsi

[Abel Vesa]

From: Neil Armstrong <neil.armstrong@xxxxxxxxxx>

Add nodes for pm8010 in separate dtsi file.

Signed-off-by: Neil Armstrong <neil.armstrong@xxxxxxxxxx>
Reviewed-by: Konrad Dybcio <konrad.dybcio@xxxxxxxxxx>
---
 arch/arm64/boot/dts/qcom/pm8010.dtsi | 84 ++++++++++++++++++++++++++++
 1 file changed, 84 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/pm8010.dtsi

diff --git a/arch/arm64/boot/dts/qcom/pm8010.dtsi b/arch/arm64/boot/dts/qcom/pm8010.dtsi
new file mode 100644
index 000000000000..0ea641e12209
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/pm8010.dtsi
@@ -0,0 +1,84 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2022, Linaro Limited
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+
+/ {
+	thermal-zones {
+		pm8010-m-thermal {
+			polling-delay-passive = <100>;
+			polling-delay = <0>;
+
+			thermal-sensors = <&pm8010_m_temp_alarm>;
+
+			trips {
+				trip0 {
+					temperature = <95000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
+
+				trip1 {
+					temperature = <115000>;
+					hysteresis = <0>;
+					type = "hot";
+				};
+			};
+		};
+
+		pm8010-n-thermal {
+			polling-delay-passive = <100>;
+			polling-delay = <0>;
+
+			thermal-sensors = <&pm8010_n_temp_alarm>;
+
+			trips {
+				trip0 {
+					temperature = <95000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
+
+				trip1 {
+					temperature = <115000>;
+					hysteresis = <0>;
+					type = "hot";
+				};
+			};
+		};
+	};
+};
+
+
+&spmi_bus {
+	pm8010_m: pmic@c {
+		compatible = "qcom,pm8010", "qcom,spmi-pmic";
+		reg = <0xc SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pm8010_m_temp_alarm: temp-alarm@2400 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0x2400>;
+			interrupts = <0xc 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
+			#thermal-sensor-cells = <0>;
+		};
+	};
+
+	pm8010_n: pmic@d {
+		compatible = "qcom,pm8010", "qcom,spmi-pmic";
+		reg = <0xd SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pm8010_n_temp_alarm: temp-alarm@2400 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0x2400>;
+			interrupts = <0xd 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
+			#thermal-sensor-cells = <0>;
+		};
+	};
+};
-- 
2.34.1