Re: [PATCH v2 4/7] arm64: dts: qcom: Add msm8939 SoC

[Konrad Dybcio]

On 3.01.2023 02:09, Bryan O'Donoghue wrote:
> Add msm8939 a derivative SoC of msm8916. This SoC contains a number of key
> differences to msm8916.
> 
> - big.LITTLE Octa Core - quad 1.5GHz + quad 1.0GHz
> - DRAM 1x800 LPDDR3
> - Camera 4+4 lane CSI
> - Venus @ 1080p60 HEVC
> - DSI x 2
> - Adreno A405
> - WiFi wcn3660/wcn3680b 802.11ac
> 
> Co-developed-by: Shawn Guo <shawn.guo@xxxxxxxxxx>
> Signed-off-by: Shawn Guo <shawn.guo@xxxxxxxxxx>
> Co-developed-by: Jun Nie <jun.nie@xxxxxxxxxx>
> Signed-off-by: Jun Nie <jun.nie@xxxxxxxxxx>
> Co-developed-by: Benjamin Li <benl@xxxxxxxxxxxx>
> Signed-off-by: Benjamin Li <benl@xxxxxxxxxxxx>
> Co-developed-by: James Willcox <jwillcox@xxxxxxxxxxxx>
> Signed-off-by: James Willcox <jwillcox@xxxxxxxxxxxx>
> Co-developed-by: Leo Yan <leo.yan@xxxxxxxxxx>
> Signed-off-by: Leo Yan <leo.yan@xxxxxxxxxx>
> Co-developed-by: Joseph Gates <jgates@xxxxxxxxxxxx>
> Signed-off-by: Joseph Gates <jgates@xxxxxxxxxxxx>
> Co-developed-by: Max Chen <mchen@xxxxxxxxxxxx>
> Signed-off-by: Max Chen <mchen@xxxxxxxxxxxx>
> Co-developed-by: Zac Crosby <zac@xxxxxxxxxxxx>
> Signed-off-by: Zac Crosby <zac@xxxxxxxxxxxx>
> Co-developed-by: Vincent Knecht <vincent.knecht@xxxxxxxxxx>
> Signed-off-by: Vincent Knecht <vincent.knecht@xxxxxxxxxx>
> Co-developed-by: Stephan Gerhold <stephan@xxxxxxxxxxx>
> Signed-off-by: Stephan Gerhold <stephan@xxxxxxxxxxx>
> Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@xxxxxxxxxx>
> ---
>  arch/arm64/boot/dts/qcom/msm8939.dtsi | 2470 +++++++++++++++++++++++++
>  1 file changed, 2470 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/qcom/msm8939.dtsi
> 
> diff --git a/arch/arm64/boot/dts/qcom/msm8939.dtsi b/arch/arm64/boot/dts/qcom/msm8939.dtsi
> new file mode 100644
> index 0000000000000..03714cdb8b69e
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/msm8939.dtsi
> @@ -0,0 +1,2470 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Copyright (c) 2013-2015, The Linux Foundation. All rights reserved.
> + * Copyright (c) 2020-2023, Linaro Limited
> + */
> +
> +#include <dt-bindings/clock/qcom,gcc-msm8939.h>
> +#include <dt-bindings/clock/qcom,rpmcc.h>
> +#include <dt-bindings/interconnect/qcom,msm8939.h>
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/power/qcom-rpmpd.h>
> +#include <dt-bindings/reset/qcom,gcc-msm8939.h>
> +#include <dt-bindings/thermal/thermal.h>
> +
> +/ {
> +	qcom,msm-id = <239 0>, <239 0x30000>, <241 0x30000>, <263 0x30000>;
> +
> +	interrupt-parent = <&intc>;
> +
> +	#address-cells = <2>;
> +	#size-cells = <2>;
> +
> +	aliases {
> +		mmc0 = &sdhc_1; /* SDC1 eMMC slot */
> +		mmc1 = &sdhc_2; /* SDC2 SD card slot */
> +	};
> +
> +	clocks {
> +		xo_board: xo-board {
> +			compatible = "fixed-clock";
> +			#clock-cells = <0>;
> +			clock-frequency = <19200000>;
> +			clock-output-names = "xo_board";
> +		};
> +
> +		sleep_clk: sleep-clk {
> +			compatible = "fixed-clock";
> +			#clock-cells = <0>;
> +			clock-frequency = <32768>;
> +			clock-output-names = "sleep_clk";
> +		};
> +	};
> +
> +	cpus {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		cpu0: cpu@100 {
> +			compatible = "arm,cortex-a53";
> +			device_type = "cpu";
> +			enable-method = "spin-table";
> +			reg = <0x100>;
> +			next-level-cache = <&L2_1>;
> +			power-domains = <&vreg_dummy>;
> +			power-domain-names = "cpr";
> +			qcom,acc = <&acc0>;
> +			qcom,saw = <&saw0>;
> +			cpu-idle-states = <&CPU_SLEEP_0>;
> +			clocks = <&apcs1_mbox>;
> +			#cooling-cells = <2>;
> +			L2_1: l2-cache@1 {
> +				compatible = "cache";
> +				cache-level = <2>;
> +			};
> +		};
> +
> +		cpu1: cpu@101 {
> +			compatible = "arm,cortex-a53";
> +			device_type = "cpu";
> +			enable-method = "spin-table";
> +			reg = <0x101>;
> +			next-level-cache = <&L2_1>;
> +			power-domains = <&vreg_dummy>;
> +			power-domain-names = "cpr";
> +			qcom,acc = <&acc1>;
> +			qcom,saw = <&saw1>;
> +			cpu-idle-states = <&CPU_SLEEP_0>;
> +			clocks = <&apcs1_mbox>;
> +			#cooling-cells = <2>;
> +		};
> +
> +		cpu2: cpu@102 {
> +			compatible = "arm,cortex-a53";
> +			device_type = "cpu";
> +			enable-method = "spin-table";
> +			reg = <0x102>;
> +			next-level-cache = <&L2_1>;
> +			power-domains = <&vreg_dummy>;
> +			power-domain-names = "cpr";
> +			qcom,acc = <&acc2>;
> +			qcom,saw = <&saw2>;
> +			cpu-idle-states = <&CPU_SLEEP_0>;
> +			clocks = <&apcs1_mbox>;
> +			#cooling-cells = <2>;
> +		};
> +
> +		cpu3: cpu@103 {
> +			compatible = "arm,cortex-a53";
> +			device_type = "cpu";
> +			enable-method = "spin-table";
> +			reg = <0x103>;
> +			next-level-cache = <&L2_1>;
> +			power-domains = <&vreg_dummy>;
> +			power-domain-names = "cpr";
> +			qcom,acc = <&acc3>;
> +			qcom,saw = <&saw3>;
> +			cpu-idle-states = <&CPU_SLEEP_0>;
> +			clocks = <&apcs1_mbox>;
> +			#cooling-cells = <2>;
> +		};
> +
> +		cpu4: cpu@0 {
> +			compatible = "arm,cortex-a53";
> +			device_type = "cpu";
> +			enable-method = "spin-table";
> +			reg = <0x0>;
> +			qcom,acc = <&acc4>;
> +			qcom,saw = <&saw4>;
> +			cpu-idle-states = <&CPU_SLEEP_0>;
> +			clocks = <&apcs0_mbox>;
> +			#cooling-cells = <2>;
> +			next-level-cache = <&L2_0>;
> +			power-domains = <&vreg_dummy>;
> +			power-domain-names = "cpr";
> +			L2_0: l2-cache@0 {
> +				compatible = "cache";
> +				cache-level = <2>;
> +			};
> +		};
> +
> +		cpu5: cpu@1 {
> +			compatible = "arm,cortex-a53";
> +			device_type = "cpu";
> +			enable-method = "spin-table";
> +			reg = <0x1>;
> +			next-level-cache = <&L2_0>;
> +			power-domains = <&vreg_dummy>;
> +			power-domain-names = "cpr";
> +			qcom,acc = <&acc5>;
> +			qcom,saw = <&saw5>;
> +			cpu-idle-states = <&CPU_SLEEP_0>;
> +			clocks = <&apcs0_mbox>;
> +			#cooling-cells = <2>;
> +		};
> +
> +		cpu6: cpu@2 {
> +			compatible = "arm,cortex-a53";
> +			device_type = "cpu";
> +			enable-method = "spin-table";
> +			reg = <0x2>;
> +			next-level-cache = <&L2_0>;
> +			power-domains = <&vreg_dummy>;
> +			power-domain-names = "cpr";
> +			qcom,acc = <&acc6>;
> +			qcom,saw = <&saw6>;
> +			cpu-idle-states = <&CPU_SLEEP_0>;
> +			clocks = <&apcs0_mbox>;
> +			#cooling-cells = <2>;
> +		};
> +
> +		cpu7: cpu@3 {
> +			compatible = "arm,cortex-a53";
> +			device_type = "cpu";
> +			enable-method = "spin-table";
> +			reg = <0x3>;
> +			next-level-cache = <&L2_0>;
> +			power-domains = <&vreg_dummy>;
> +			power-domain-names = "cpr";
> +			qcom,acc = <&acc7>;
> +			qcom,saw = <&saw7>;
> +			cpu-idle-states = <&CPU_SLEEP_0>;
> +			clocks = <&apcs0_mbox>;
> +			#cooling-cells = <2>;
> +		};
> +
> +		idle-states {
> +			CPU_SLEEP_0: cpu-sleep-0 {
> +				compatible ="qcom,idle-state-spc", "arm,idle-state";
> +				entry-latency-us = <130>;
> +				exit-latency-us = <150>;
> +				min-residency-us = <2000>;
> +				local-timer-stop;
> +			};
> +		};
> +	};
> +
> +	/*
> +	 * MSM8939 has a big.LITTLE heterogeneous computing architecture,
> +	 * consisting of two clusters of four ARM Cortex-A53s each. The
> +	 * LITTLE cluster runs at 1.0-1.2GHz, and the big cluster runs
> +	 * at 1.5-1.7GHz.
> +	 *
> +	 * The enable method used here is spin-table which presupposes use
> +	 * of a 2nd stage boot shim such as lk2nd to have installed a
> +	 * spin-table, the downstream non-psci/non-spin-table method that
> +	 * default msm8916/msm8936/msm8939 will not be supported upstream.
> +	 */
> +	cpu-map {
> +		/* LITTLE (efficiency) cluster */
> +		cluster0 {
> +			core0 {
> +				cpu = <&cpu4>;
> +			};
> +
> +			core1 {
> +				cpu = <&cpu5>;
> +			};
> +
> +			core2 {
> +				cpu = <&cpu6>;
> +			};
> +
> +			core3 {
> +				cpu = <&cpu7>;
> +			};
> +		};
> +
> +		/* big (performance) cluster */
> +		/* Boot CPU is cluster 1 core 0 */
> +		cluster1 {
> +			core0 {
> +				cpu = <&cpu0>;
> +			};
> +
> +			core1 {
> +				cpu = <&cpu1>;
> +			};
> +
> +			core2 {
> +				cpu = <&cpu2>;
> +			};
> +
> +			core3 {
> +				cpu = <&cpu3>;
> +			};
> +		};
> +	};
> +
> +	firmware {
> +		scm: scm {
> +			compatible = "qcom,scm-msm8916", "qcom,scm";
> +			clocks = <&gcc GCC_CRYPTO_CLK>,
> +				 <&gcc GCC_CRYPTO_AXI_CLK>,
> +				 <&gcc GCC_CRYPTO_AHB_CLK>;
> +			clock-names = "core", "bus", "iface";
> +			#reset-cells = <1>;
> +
> +			qcom,dload-mode = <&tcsr 0x6100>;
> +		};
> +	};
> +
> +	hexagon-smp2p {
> +		compatible = "qcom,smp2p";
> +		qcom,smem = <435>, <428>;
> +
> +		interrupts = <GIC_SPI 27 IRQ_TYPE_EDGE_RISING>;
> +
> +		mboxes = <&apcs1_mbox 14>;
> +
> +		qcom,local-pid = <0>;
> +		qcom,remote-pid = <1>;
> +
> +		hexagon_smp2p_out: master-kernel {
> +			qcom,entry-name = "master-kernel";
> +
> +			#qcom,smem-state-cells = <1>;
> +		};
> +
> +		hexagon_smp2p_in: slave-kernel {
> +			qcom,entry-name = "slave-kernel";
> +
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +		};
> +	};
> +
> +	memory@80000000 {
> +		device_type = "memory";
> +		/* We expect the bootloader to fill in the reg */
> +		reg = <0x0 0x80000000 0x0 0x0>;
> +	};
> +
> +	pmu {
> +		compatible = "arm,cortex-a53-pmu";
> +		interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(8)| IRQ_TYPE_LEVEL_HIGH)>;
> +	};
> +
> +	reserved-memory {
> +		#address-cells = <2>;
> +		#size-cells = <2>;
> +		ranges;
> +
> +		tz-apps@86000000 {
> +			reg = <0x0 0x86000000 0x0 0x300000>;
> +			no-map;
> +		};
> +
> +		smem_mem: smem@86300000 {
> +			reg = <0x0 0x86300000 0x0 0x100000>;
> +			no-map;
> +		};
> +
> +		hypervisor@86400000 {
> +			reg = <0x0 0x86400000 0x0 0x100000>;
> +			no-map;
> +		};
> +
> +		tz@86500000 {
> +			reg = <0x0 0x86500000 0x0 0x180000>;
> +			no-map;
> +		};
> +
> +		reserved@86680000 {
> +			reg = <0x0 0x86680000 0x0 0x80000>;
> +			no-map;
> +		};
> +
> +		rmtfs@86700000 {
> +			compatible = "qcom,rmtfs-mem";
> +			reg = <0x0 0x86700000 0x0 0xe0000>;
> +			no-map;
> +
> +			qcom,client-id = <1>;
> +		};
> +
> +		rfsa@867e0000 {
> +			reg = <0x0 0x867e0000 0x0 0x20000>;
> +			no-map;
> +		};
> +
> +		mpss_mem: mpss@86800000 {
> +			reg = <0x0 0x86800000 0x0 0x5500000>;
> +			no-map;
> +		};
> +
> +		wcnss_mem: wcnss@8bd00000 {
> +			reg = <0x0 0x8bd00000 0x0 0x600000>;
> +			no-map;
> +		};
> +
> +		venus_mem: venus@8c300000 {
> +			reg = <0x0 0x8c300000 0x0 0x800000>;
> +			no-map;
> +		};
> +
> +		mba_mem: mba@8cb00000 {
> +			no-map;
> +			reg = <0x0 0x8cb00000 0x0 0x100000>;
> +		};
> +	};
> +
> +	smem {
> +		compatible = "qcom,smem";
> +
> +		memory-region = <&smem_mem>;
> +		qcom,rpm-msg-ram = <&rpm_msg_ram>;
> +
> +		hwlocks = <&tcsr_mutex 3>;
> +	};
> +
> +	smsm {
> +		compatible = "qcom,smsm";
> +
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		qcom,ipc-1 = <&apcs1_mbox 8 13>;
> +		qcom,ipc-3 = <&apcs1_mbox 8 19>;
> +
> +		apps_smsm: apps@0 {
> +			reg = <0>;
> +
> +			#qcom,smem-state-cells = <1>;
> +		};
> +
> +		hexagon_smsm: hexagon@1 {
> +			reg = <1>;
> +			interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>;
> +
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +		};
> +
> +		wcnss_smsm: wcnss@6 {
> +			reg = <6>;
> +			interrupts = <GIC_SPI 144 IRQ_TYPE_EDGE_RISING>;
> +
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +		};
> +	};
> +
> +	soc: soc@0 {
> +
> +		compatible = "simple-bus";
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		ranges = <0 0 0 0xffffffff>;
> +
> +		rng@22000 {
> +			compatible = "qcom,prng";
> +			reg = <0x00022000 0x200>;
> +			clocks = <&gcc GCC_PRNG_AHB_CLK>;
> +			clock-names = "core";
> +		};
> +
> +		qfprom: qfprom@5c000 {
> +			compatible = "qcom,msm8916-qfprom", "qcom,qfprom";
> +			reg = <0x0005c000 0x1000>;
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			tsens_caldata: caldata@a0 {
> +				reg = <0xa0 0x5c>;
> +			};
> +			cpr_efuse_init_voltage1: ivoltage1@dc {
> +				reg = <0xdc 0x4>;
> +				bits = <4 6>;
> +			};
> +			cpr_efuse_init_voltage2: ivoltage2@da {
> +				reg = <0xda 0x4>;
> +				bits = <2 6>;
> +			};
> +			cpr_efuse_init_voltage3: ivoltage3@d8 {
> +				reg = <0xd8 0x4>;
> +				bits = <0 6>;
> +			};
> +			cpr_efuse_quot1: quot1@dc {
> +				reg = <0xdd 0x8>;
> +				bits = <2 12>;
> +			};
> +			cpr_efuse_quot2: quot2@da {
> +				reg = <0xdb 0x8>;
> +				bits = <0x0 12>;
> +			};
> +			cpr_efuse_quot3: quot3@d8 {
> +				reg = <0xd8 0x8>;
> +				bits = <6 12>;
> +			};
> +			cpr_efuse_ring1: ring1@de {
> +				reg = <0xde 0x4>;
> +				bits = <6 3>;
> +			};
> +			cpr_efuse_ring2: ring2@de {
> +				reg = <0xde 0x4>;
> +				bits = <6 3>;
> +			};
> +			cpr_efuse_ring3: ring3@de {
> +				reg = <0xde 0x4>;
> +				bits = <6 3>;
> +			};
> +			cpr_efuse_revision: revision@4 {
> +				reg = <0x5 0x1>;
> +				bits = <5 1>;
> +			};
> +			cpr_efuse_revision_high: revision-high@4 {
> +				reg = <0x7 0x1>;
> +				bits = <0 1>;
> +			};
> +			cpr_efuse_pvs_version: pvs@4 {
> +				reg = <0x3 0x1>;
> +				bits = <5 1>;
> +			};
> +			cpr_efuse_pvs_version_high: pvs-high@4 {
> +				reg = <0x6 0x1>;
> +				bits = <2 2>;
> +			};
> +			cpr_efuse_speedbin: speedbin@c {
> +				reg = <0xc 0x1>;
> +				bits = <2 3>;
> +			};
> +
> +		};
> +
> +		rpm_msg_ram: sram@60000 {
> +			compatible = "qcom,rpm-msg-ram";
> +			reg = <0x00060000 0x8000>;
> +		};
> +
> +		bimc: interconnect@400000 {
> +			compatible = "qcom,msm8939-bimc";
> +			reg = <0x00400000 0x62000>;
> +			clock-names = "bus", "bus_a";
> +			clocks = <&rpmcc RPM_SMD_BIMC_CLK>,
> +				 <&rpmcc RPM_SMD_BIMC_A_CLK>;
> +			#interconnect-cells = <1>;
> +			status = "okay";
> +		};
> +
> +		tsens: thermal-sensor@4a9000 {
> +			compatible = "qcom,msm8939-tsens", "qcom,tsens-v0_1";
> +			reg = <0x004a9000 0x1000>, /* TM */
> +			      <0x004a8000 0x1000>; /* SROT */
> +			nvmem-cells = <&tsens_caldata>;
> +			nvmem-cell-names = "calib";
> +			#qcom,sensors = <10>;
> +			interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
> +			interrupt-names = "uplow";
> +			#thermal-sensor-cells = <1>;
> +		};
> +
> +		restart@4ab000 {
> +			compatible = "qcom,pshold";
> +			reg = <0x004ab000 0x4>;
> +		};
> +
> +		pcnoc: interconnect@500000 {
> +			compatible = "qcom,msm8939-pcnoc";
> +			reg = <0x00500000 0x11000>;
> +			clock-names = "bus", "bus_a";
> +			clocks = <&rpmcc RPM_SMD_PCNOC_CLK>,
> +				 <&rpmcc RPM_SMD_PCNOC_A_CLK>;
> +			#interconnect-cells = <1>;
> +			status = "okay";
> +		};
> +
> +		snoc: interconnect@580000 {
> +			compatible = "qcom,msm8939-snoc";
> +			reg = <0x00580000 0x14080>;
> +			clock-names = "bus", "bus_a";
> +			clocks = <&rpmcc RPM_SMD_SNOC_CLK>,
> +				 <&rpmcc RPM_SMD_SNOC_A_CLK>;
> +			#interconnect-cells = <1>;
> +			status = "okay";
> +
> +			snoc_mm: interconnect-snoc {
> +				compatible = "qcom,msm8939-snoc-mm";
> +				clock-names = "bus", "bus_a";
> +				clocks = <&rpmcc RPM_SMD_SYSMMNOC_CLK>,
> +					 <&rpmcc RPM_SMD_SYSMMNOC_A_CLK>;
> +				#interconnect-cells = <1>;
> +				status = "okay";
> +			};
> +
> +		};
> +
> +		msmgpio: pinctrl@1000000 {
> +			compatible = "qcom,msm8916-pinctrl";
> +			reg = <0x01000000 0x300000>;
> +			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
> +			gpio-controller;
> +			gpio-ranges = <&msmgpio 0 0 122>;
> +			#gpio-cells = <2>;
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +
> +			blsp1_uart1_default: blsp1-uart1-default-state {
> +				pins = "gpio0", "gpio1", "gpio2", "gpio3";
> +				function = "blsp_uart1";
> +
> +				drive-strength = <16>;
> +				bias-disable;
> +			};
> +
> +			blsp1_uart1_sleep: blsp1-uart1-sleep-state {
> +				pins = "gpio0", "gpio1", "gpio2", "gpio3";
> +				function = "gpio";
> +
> +				drive-strength = <2>;
> +				bias-pull-down;
> +			};
> +
> +			blsp1_uart2_default: blsp1-uart2-default-state {
> +				pins = "gpio4", "gpio5";
> +				function = "blsp_uart2";
> +
> +				drive-strength = <16>;
> +				bias-disable;
> +			};
> +
> +			blsp1_uart2_sleep: blsp1-uart2-sleep-state {
> +				pins = "gpio4", "gpio5";
> +				function = "gpio";
> +
> +				drive-strength = <2>;
> +				bias-pull-down;
> +			};
> +
> +			camera_front_default: camera-front-default-state {
> +				pwdn-pins {
> +					pins = "gpio33";
> +					function = "gpio";
> +
> +					drive-strength = <16>;
> +					bias-disable;
> +				};
> +				rst-pins {
> +					pins = "gpio28";
> +					function = "gpio";
> +
> +					drive-strength = <16>;
> +					bias-disable;
> +				};
> +				mclk1-pins {
> +					pins = "gpio27";
> +					function = "cam_mclk1";
> +
> +					drive-strength = <16>;
> +					bias-disable;
> +				};
> +			};
> +
> +			camera_rear_default: camera-rear-default-state {
> +				pwdn-pins {
> +					pins = "gpio34";
> +					function = "gpio";
> +
> +					drive-strength = <16>;
> +					bias-disable;
> +				};
> +				rst-pins {
> +					pins = "gpio35";
> +					function = "gpio";
> +
> +					drive-strength = <16>;
> +					bias-disable;
> +				};
> +				mclk0-pins {
> +					pins = "gpio26";
> +					function = "cam_mclk0";
> +
> +					drive-strength = <16>;
> +					bias-disable;
> +				};
> +			};
> +
> +			cci0_default: cci0-default-state {
> +				pins = "gpio29", "gpio30";
> +				function = "cci_i2c";
> +
> +				drive-strength = <16>;
> +				bias-disable;
> +			};
> +
> +			cdc-pdm-lines-state {
> +				cdc_pdm_lines_act: pdm-lines-on-pins {
> +					pins = "gpio63", "gpio64", "gpio65", "gpio66",
> +					       "gpio67", "gpio68";
> +					function = "cdc_pdm0";
> +
> +					drive-strength = <8>;
> +					bias-disable;
> +				};
> +				cdc_pdm_lines_sus: pdm-lines-off-pins {
> +					pins = "gpio63", "gpio64", "gpio65", "gpio66",
> +					       "gpio67", "gpio68";
> +					function = "cdc_pdm0";
> +
> +					drive-strength = <2>;
> +					bias-pull-down;
> +				};
> +			};
> +
> +			cdc_dmic_lines_act: cdc-dmic-lines-on-state {
> +				clk-pins {
> +					pins = "gpio0";
> +					function = "dmic0_clk";
> +
> +					drive-strength = <8>;
> +				};
> +				data-pins {
> +					pins = "gpio1";
> +					function = "dmic0_data";
> +
> +					drive-strength = <8>;
> +				};
> +			};
> +			cdc_dmic_lines_sus: cdc-dmic-lines-off-state {
> +				clk-pins {
> +					pins = "gpio0";
> +					function = "dmic0_clk";
> +
> +					drive-strength = <2>;
> +					bias-disable;
> +				};
> +				data-pins {
> +					pins = "gpio1";
> +					function = "dmic0_data";
> +
> +					drive-strength = <2>;
> +					bias-disable;
> +				};
> +			};
> +
> +			ext-mclk-tlmm-lines-state {
> +				ext_mclk_tlmm_lines_act: mclk-lines-on-pins {
> +					pins = "gpio116";
> +					function = "pri_mi2s";
> +
> +					drive-strength = <8>;
> +					bias-disable;
> +				};
> +				ext_mclk_tlmm_lines_sus: mclk-lines-off-pins {
> +					pins = "gpio116";
> +					function = "pri_mi2s";
> +
> +					drive-strength = <2>;
> +					bias-disable;
> +				};
> +			};
> +
> +			ext-pri-tlmm-lines-state {
> +				ext_pri_tlmm_lines_act: ext-pa-on-pins {
> +					pins = "gpio113", "gpio114", "gpio115", "gpio116";
> +					function = "pri_mi2s";
> +
> +					drive-strength = <8>;
> +					bias-disable;
> +				};
> +				ext_pri_tlmm_lines_sus: ext-pa-off-pins {
> +					pins = "gpio113", "gpio114", "gpio115", "gpio116";
> +					function = "pri_mi2s";
> +
> +					drive-strength = <2>;
> +					bias-disable;
> +				};
> +			};
> +
> +			ext-pri-ws-line-state {
> +				ext_pri_ws_act: ext-pa-on-pins {
> +					pins = "gpio110";
> +					function = "pri_mi2s_ws";
> +
> +					drive-strength = <8>;
> +					bias-disable;
> +				};
> +				ext_pri_ws_sus: ext-pa-off-pins {
> +					pins = "gpio110";
> +					function = "pri_mi2s_ws";
> +
> +					drive-strength = <2>;
> +					bias-disable;
> +				};
> +			};
> +
> +			/* secondary Mi2S */
> +			ext-sec-tlmm-lines-state {
> +				ext_sec_tlmm_lines_act: tlmm-lines-on-pins {
> +					pins = "gpio112", "gpio117", "gpio118", "gpio119";
> +					function = "sec_mi2s";
> +
> +					drive-strength = <8>;
> +					bias-disable;
> +				};
> +				ext_sec_tlmm_lines_sus: tlmm-lines-off-pins {
> +					pins = "gpio112", "gpio117", "gpio118", "gpio119";
> +					function = "sec_mi2s";
> +
> +					drive-strength = <2>;
> +					bias-disable;
> +				};
> +			};
> +
> +			i2c1_default: i2c1-default-state {
> +				pins = "gpio2", "gpio3";
> +				function = "blsp_i2c1";
> +
> +				drive-strength = <2>;
> +				bias-disable;
> +			};
> +
> +			i2c1_sleep: i2c1-sleep-state {
> +				pins = "gpio2", "gpio3";
> +				function = "gpio";
> +
> +				drive-strength = <2>;
> +				bias-disable;
> +			};
> +
> +			i2c2_default: i2c2-default-state {
> +				pins = "gpio6", "gpio7";
> +				function = "blsp_i2c2";
> +
> +				drive-strength = <2>;
> +				bias-disable;
> +			};
> +
> +			i2c2_sleep: i2c2-sleep-state {
> +				pins = "gpio6", "gpio7";
> +				function = "gpio";
> +
> +				drive-strength = <2>;
> +				bias-disable;
> +			};
> +
> +			i2c3_default: i2c3-default-state {
> +				pins = "gpio10", "gpio11";
> +				function = "blsp_i2c3";
> +
> +				drive-strength = <2>;
> +				bias-disable;
> +			};
> +
> +			i2c3_sleep: i2c3-sleep-state {
> +				pins = "gpio10", "gpio11";
> +				function = "gpio";
> +
> +				drive-strength = <2>;
> +				bias-disable;
> +			};
> +
> +			i2c4_default: i2c4-default-state {
> +				pins = "gpio14", "gpio15";
> +				function = "blsp_i2c4";
> +
> +				drive-strength = <2>;
> +				bias-disable;
> +			};
> +
> +			i2c4_sleep: i2c4-sleep-state {
> +				pins = "gpio14", "gpio15";
> +				function = "gpio";
> +
> +				drive-strength = <2>;
> +				bias-disable;
> +			};
> +
> +			i2c5_default: i2c5-default-state {
> +				pins = "gpio18", "gpio19";
> +				function = "blsp_i2c5";
> +
> +				drive-strength = <2>;
> +				bias-disable;
> +			};
> +
> +			i2c5_sleep: i2c5-sleep-state {
> +				pins = "gpio18", "gpio19";
> +				function = "gpio";
> +
> +				drive-strength = <2>;
> +				bias-disable;
> +			};
> +
> +			i2c6_default: i2c6-default-state {
> +				pins = "gpio22", "gpio23";
> +				function = "blsp_i2c6";
> +
> +				drive-strength = <2>;
> +				bias-disable;
> +			};
> +
> +			i2c6_sleep: i2c6-sleep-state {
> +				pins = "gpio22", "gpio23";
> +				function = "gpio";
> +
> +				drive-strength = <2>;
> +				bias-disable;
> +			};
> +
> +			pmx-sdc1-clk-state {
> +				sdc1_clk_on: clk-on-pins {
> +					pins = "sdc1_clk";
One more thing, you can define all sdc pins for a given state
in a single pin group, sort of like in sm8450.dtsi

https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux.git/commit/arch/arm64/boot/dts/qcom/sm8450.dtsi?h=for-next&id=a0646262ec94faaf95b3dba8f17774d9762ee9ac

Konrad
> +
> +					bias-disable;
> +					drive-strength = <16>;
> +				};
> +				sdc1_clk_off: clk-off-pins {
> +					pins = "sdc1_clk";
> +
> +					bias-disable;
> +					drive-strength = <2>;
> +				};
> +			};
> +
> +			pmx-sdc1-cmd-state {
> +				sdc1_cmd_on: cmd-on-pins {
> +					pins = "sdc1_cmd";
> +
> +					bias-pull-up;
> +					drive-strength = <10>;
> +				};
> +				sdc1_cmd_off: cmd-off-pins {
> +					pins = "sdc1_cmd";
> +
> +					bias-pull-up;
> +					drive-strength = <2>;
> +				};
> +			};
> +
> +			pmx-sdc1-data-state {
> +				sdc1_data_on: data-on-pins {
> +					pins = "sdc1_data";
> +
> +					bias-pull-up;
> +					drive-strength = <10>;
> +				};
> +				sdc1_data_off: data-off-pins {
> +					pins = "sdc1_data";
> +
> +					bias-pull-up;
> +					drive-strength = <2>;
> +				};
> +			};
> +
> +			pmx-sdc2-clk-state {
> +				sdc2_clk_on: clk-on-pins {
> +					pins = "sdc2_clk";
> +
> +					bias-disable;
> +					drive-strength = <16>;
> +				};
> +				sdc2_clk_off: clk-off-pins {
> +					pins = "sdc2_clk";
> +
> +					bias-disable;
> +					drive-strength = <2>;
> +				};
> +			};
> +
> +			pmx-sdc2-cmd-state {
> +				sdc2_cmd_on: cmd-on-pins {
> +					pins = "sdc2_cmd";
> +
> +					bias-pull-up;
> +					drive-strength = <10>;
> +				};
> +				sdc2_cmd_off: cmd-off-pins {
> +					pins = "sdc2_cmd";
> +
> +					bias-pull-up;
> +					drive-strength = <2>;
> +				};
> +			};
> +
> +			pmx-sdc2-data-state {
> +				sdc2_data_on: data-on-pins {
> +					pins = "sdc2_data";
> +
> +					bias-pull-up;
> +					drive-strength = <10>;
> +				};
> +				sdc2_data_off: data-off-pins {
> +					pins = "sdc2_data";
> +
> +					bias-pull-up;
> +					drive-strength = <2>;
> +				};
> +			};
> +
> +			pmx-sdc2-cd-pin-state {
> +				sdc2_cd_on: cd-on-pins {
> +					pins = "gpio38";
> +					function = "gpio";
> +
> +					drive-strength = <2>;
> +					bias-pull-up;
> +				};
> +				sdc2_cd_off: cd-off-pins {
> +					pins = "gpio38";
> +					function = "gpio";
> +
> +					drive-strength = <2>;
> +					bias-disable;
> +				};
> +			};
> +
> +			spi1_default: spi1-default-state {
> +				spi-pins {
> +					pins = "gpio0", "gpio1", "gpio3";
> +					function = "blsp_spi1";
> +
> +					drive-strength = <12>;
> +					bias-disable;
> +				};
> +				cs-pins {
> +					pins = "gpio2";
> +					function = "gpio";
> +
> +					drive-strength = <16>;
> +					bias-disable;
> +					output-high;
> +				};
> +			};
> +
> +			spi1_sleep: spi1-sleep-state {
> +				pins = "gpio0", "gpio1", "gpio2", "gpio3";
> +				function = "gpio";
> +
> +				drive-strength = <2>;
> +				bias-pull-down;
> +			};
> +
> +			spi2_default: spi2-default-state {
> +				spi-pins {
> +					pins = "gpio4", "gpio5", "gpio7";
> +					function = "blsp_spi2";
> +
> +					drive-strength = <12>;
> +					bias-disable;
> +				};
> +				cs-pins {
> +					pins = "gpio6";
> +					function = "gpio";
> +
> +					drive-strength = <16>;
> +					bias-disable;
> +					output-high;
> +				};
> +			};
> +
> +			spi2_sleep: spi2-sleep-state {
> +				pins = "gpio4", "gpio5", "gpio6", "gpio7";
> +				function = "gpio";
> +
> +				drive-strength = <2>;
> +				bias-pull-down;
> +			};
> +
> +			spi3_default: spi3-default-state {
> +				spi-pins {
> +					pins = "gpio8", "gpio9", "gpio11";
> +					function = "blsp_spi3";
> +
> +					drive-strength = <12>;
> +					bias-disable;
> +				};
> +				cs-pins {
> +					pins = "gpio10";
> +					function = "gpio";
> +
> +					drive-strength = <16>;
> +					bias-disable;
> +					output-high;
> +				};
> +			};
> +
> +			spi3_sleep: spi3-sleep-state {
> +				pins = "gpio8", "gpio9", "gpio10", "gpio11";
> +				function = "gpio";
> +
> +				drive-strength = <2>;
> +				bias-pull-down;
> +			};
> +
> +			spi4_default: spi4-default-state {
> +				spi-pins {
> +					pins = "gpio12", "gpio13", "gpio15";
> +					function = "blsp_spi4";
> +
> +					drive-strength = <12>;
> +					bias-disable;
> +				};
> +				cs-pins {
> +					pins = "gpio14";
> +					function = "gpio";
> +
> +					drive-strength = <16>;
> +					bias-disable;
> +					output-high;
> +				};
> +			};
> +
> +			spi4_sleep: spi4-sleep-state {
> +				pins = "gpio12", "gpio13", "gpio14", "gpio15";
> +				function = "gpio";
> +
> +				drive-strength = <2>;
> +				bias-pull-down;
> +			};
> +
> +			spi5_default: spi5-default-state {
> +				spi-pins {
> +					pins = "gpio16", "gpio17", "gpio19";
> +					function = "blsp_spi5";
> +
> +					drive-strength = <12>;
> +					bias-disable;
> +				};
> +				cs-pins {
> +					pins = "gpio18";
> +					function = "gpio";
> +
> +					drive-strength = <16>;
> +					bias-disable;
> +					output-high;
> +				};
> +			};
> +
> +			spi5_sleep: spi5-sleep-state {
> +				pins = "gpio16", "gpio17", "gpio18", "gpio19";
> +				function = "gpio";
> +
> +				drive-strength = <2>;
> +				bias-pull-down;
> +			};
> +
> +			spi6_default: spi6-default-state {
> +				spi-pins {
> +					pins = "gpio20", "gpio21", "gpio23";
> +					function = "blsp_spi6";
> +
> +					drive-strength = <12>;
> +					bias-disable;
> +				};
> +				cs-pins {
> +					pins = "gpio22";
> +					function = "gpio";
> +
> +					drive-strength = <16>;
> +					bias-disable;
> +					output-high;
> +				};
> +			};
> +
> +			spi6_sleep: spi6-sleep-state {
> +				pins = "gpio20", "gpio21", "gpio22", "gpio23";
> +				function = "gpio";
> +
> +				drive-strength = <2>;
> +				bias-pull-down;
> +			};
> +
> +			wcnss_pin_a: wcnss-active-state {
> +				pins = "gpio40", "gpio41", "gpio42", "gpio43", "gpio44";
> +				function = "wcss_wlan";
> +
> +				drive-strength = <6>;
> +				bias-pull-up;
> +			};
> +		};
> +
> +		gcc: clock-controller@1800000 {
> +			compatible = "qcom,gcc-msm8939";
> +			reg = <0x01800000 0x80000>;
> +			clocks = <&xo_board>,
> +				 <&sleep_clk>,
> +				 <&dsi_phy0 1>,
> +				 <&dsi_phy0 0>,
> +				 <0>,
> +				 <0>,
> +				 <0>;
> +			clock-names = "xo",
> +				      "sleep_clk",
> +				      "dsi0pll",
> +				      "dsi0pllbyte",
> +				      "ext_mclk",
> +				      "ext_pri_i2s",
> +				      "ext_sec_i2s";
> +			#clock-cells = <1>;
> +			#reset-cells = <1>;
> +			#power-domain-cells = <1>;
> +		};
> +
> +		tcsr_mutex: hwlock@1905000 {
> +			compatible = "qcom,tcsr-mutex";
> +			reg = <0x01905000 0x20000>;
> +			#hwlock-cells = <1>;
> +		};
> +
> +		tcsr: syscon@1937000 {
> +			compatible = "qcom,tcsr-msm8916", "syscon";
> +			reg = <0x01937000 0x30000>;
> +		};
> +
> +		mdss: mdss@1a00000 {
> +			compatible = "qcom,mdss";
> +			reg = <0x01a00000 0x1000>,
> +			      <0x01ac8000 0x3000>;
> +			reg-names = "mdss_phys", "vbif_phys";
> +
> +			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
> +			interrupt-controller;
> +
> +			clocks = <&gcc GCC_MDSS_AHB_CLK>,
> +				 <&gcc GCC_MDSS_AXI_CLK>,
> +				 <&gcc GCC_MDSS_VSYNC_CLK>;
> +			clock-names = "iface",
> +				      "bus",
> +				      "vsync";
> +
> +			power-domains = <&gcc MDSS_GDSC>;
> +
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			#interrupt-cells = <1>;
> +			ranges;
> +
> +			mdp: mdp@1a01000 {
> +				compatible = "qcom,mdp5";
> +				reg = <0x01a01000 0x89000>;
> +				reg-names = "mdp_phys";
> +
> +				interrupt-parent = <&mdss>;
> +				interrupts = <0>;
> +
> +				clocks = <&gcc GCC_MDSS_AHB_CLK>,
> +					 <&gcc GCC_MDSS_AXI_CLK>,
> +					 <&gcc GCC_MDSS_MDP_CLK>,
> +					 <&gcc GCC_MDSS_VSYNC_CLK>,
> +					 <&gcc GCC_MDP_TBU_CLK>,
> +					 <&gcc GCC_MDP_RT_TBU_CLK>;
> +				clock-names = "iface",
> +					      "bus",
> +					      "core",
> +					      "vsync",
> +					      "tbu",
> +					      "tbu_rt";
> +
> +				iommus = <&apps_iommu 4>;
> +
> +				interconnects = <&snoc_mm MASTER_MDP_PORT0 &bimc SLAVE_EBI_CH0>,
> +						<&snoc_mm MASTER_MDP_PORT1 &bimc SLAVE_EBI_CH0>,
> +						<&pcnoc MASTER_SPDM &snoc SLAVE_IMEM>;
> +				interconnect-names = "mdp0-mem", "mdp1-mem", "register-mem";
> +
> +				ports {
> +					#address-cells = <1>;
> +					#size-cells = <0>;
> +
> +					port@0 {
> +						reg = <0>;
> +						mdp5_intf1_out: endpoint {
> +							remote-endpoint = <&dsi0_in>;
> +						};
> +					};
> +
> +					port@1 {
> +						reg = <1>;
> +						mdp5_intf2_out: endpoint {
> +							remote-endpoint = <&dsi1_in>;
> +						};
> +					};
> +				};
> +			};
> +
> +			dsi0: dsi@1a98000 {
> +				compatible = "qcom,msm8916-dsi-ctrl",
> +					     "qcom,mdss-dsi-ctrl";
> +				reg = <0x01a98000 0x25c>;
> +				reg-names = "dsi_ctrl";
> +
> +				interrupt-parent = <&mdss>;
> +				interrupts = <4>;
> +
> +				power-domains = <&gcc MDSS_GDSC>;
> +
> +				clocks = <&gcc GCC_MDSS_MDP_CLK>,
> +					 <&gcc GCC_MDSS_AHB_CLK>,
> +					 <&gcc GCC_MDSS_AXI_CLK>,
> +					 <&gcc GCC_MDSS_BYTE0_CLK>,
> +					 <&gcc GCC_MDSS_PCLK0_CLK>,
> +					 <&gcc GCC_MDSS_ESC0_CLK>;
> +				clock-names = "mdp_core",
> +					      "iface",
> +					      "bus",
> +					      "byte",
> +					      "pixel",
> +					      "core";
> +				assigned-clocks = <&gcc BYTE0_CLK_SRC>,
> +						  <&gcc PCLK0_CLK_SRC>;
> +				assigned-clock-parents = <&dsi_phy0 0>,
> +							 <&dsi_phy0 1>;
> +
> +				phys = <&dsi_phy0>;
> +				status = "disabled";
> +
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				ports {
> +					#address-cells = <1>;
> +					#size-cells = <0>;
> +
> +					port@0 {
> +						reg = <0>;
> +						dsi0_in: endpoint {
> +							remote-endpoint = <&mdp5_intf1_out>;
> +						};
> +					};
> +
> +					port@1 {
> +						reg = <1>;
> +						dsi0_out: endpoint {
> +						};
> +					};
> +				};
> +			};
> +
> +			dsi_phy0: phy@1a98300 {
> +				compatible = "qcom,dsi-phy-28nm-lp";
> +				reg = <0x01a98300 0xd4>,
> +				      <0x01a98500 0x280>,
> +				      <0x01a98780 0x30>;
> +				reg-names = "dsi_pll",
> +					    "dsi_phy",
> +					    "dsi_phy_regulator";
> +
> +				clocks = <&gcc GCC_MDSS_AHB_CLK>,
> +					 <&xo_board>;
> +				clock-names = "iface", "ref";
> +
> +				#clock-cells = <1>;
> +				#phy-cells = <0>;
> +				status = "disabled";
> +			};
> +
> +			dsi1: dsi@1aa0000 {
> +				compatible = "qcom,msm8916-dsi-ctrl",
> +					     "qcom,mdss-dsi-ctrl";
> +				reg = <0x01aa0000 0x25c>;
> +				reg-names = "dsi_ctrl";
> +
> +				interrupt-parent = <&mdss>;
> +				interrupts = <5>;
> +
> +				power-domains = <&gcc MDSS_GDSC>;
> +
> +				clocks = <&gcc GCC_MDSS_MDP_CLK>,
> +					 <&gcc GCC_MDSS_AHB_CLK>,
> +					 <&gcc GCC_MDSS_AXI_CLK>,
> +					 <&gcc GCC_MDSS_BYTE1_CLK>,
> +					 <&gcc GCC_MDSS_PCLK1_CLK>,
> +					 <&gcc GCC_MDSS_ESC1_CLK>;
> +				clock-names = "mdp_core",
> +					      "iface",
> +					      "bus",
> +					      "byte",
> +					      "pixel",
> +					      "core";
> +				assigned-clocks = <&gcc BYTE1_CLK_SRC>,
> +						  <&gcc PCLK1_CLK_SRC>;
> +				assigned-clock-parents = <&dsi_phy1 0>,
> +							 <&dsi_phy1 1>;
> +				phys = <&dsi_phy1>;
> +				status = "disabled";
> +
> +				ports {
> +					#address-cells = <1>;
> +					#size-cells = <0>;
> +
> +					port@0 {
> +						reg = <0>;
> +						dsi1_in: endpoint {
> +							remote-endpoint = <&mdp5_intf2_out>;
> +						};
> +					};
> +
> +					port@1 {
> +						reg = <1>;
> +						dsi1_out: endpoint {
> +						};
> +					};
> +				};
> +			};
> +
> +			dsi_phy1: phy@1aa0300 {
> +				compatible = "qcom,dsi-phy-28nm-lp";
> +				reg = <0x01aa0300 0xd4>,
> +				      <0x01aa0500 0x280>,
> +				      <0x01aa0780 0x30>;
> +				reg-names = "dsi_pll",
> +					    "dsi_phy",
> +					    "dsi_phy_regulator";
> +
> +				clocks = <&gcc GCC_MDSS_AHB_CLK>,
> +					 <&xo_board>;
> +				clock-names = "iface", "ref";
> +
> +				#clock-cells = <1>;
> +				#phy-cells = <0>;
> +				status = "disabled";
> +			};
> +		};
> +
> +		gpu@1c00000 {
> +			compatible = "qcom,adreno-405.0", "qcom,adreno";
> +			reg = <0x01c00000 0x10000>;
> +			reg-names = "kgsl_3d0_reg_memory";
> +			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
> +			interrupt-names = "kgsl_3d0_irq";
> +			clock-names = "core",
> +				      "iface",
> +				      "mem",
> +				      "mem_iface",
> +				      "alt_mem_iface",
> +				      "gfx3d",
> +				      "rbbmtimer";
> +			clocks = <&gcc GCC_OXILI_GFX3D_CLK>,
> +				 <&gcc GCC_OXILI_AHB_CLK>,
> +				 <&gcc GCC_OXILI_GMEM_CLK>,
> +				 <&gcc GCC_BIMC_GFX_CLK>,
> +				 <&gcc GCC_BIMC_GPU_CLK>,
> +				 <&gcc GFX3D_CLK_SRC>,
> +				 <&gcc GCC_OXILI_TIMER_CLK>;
> +			power-domains = <&gcc OXILI_GDSC>;
> +			operating-points-v2 = <&opp_table>;
> +			iommus = <&gpu_iommu 1>, <&gpu_iommu 2>;
> +
> +			opp_table: opp-table {
> +				compatible = "operating-points-v2";
> +
> +				opp-550000000 {
> +					opp-hz = /bits/ 64 <550000000>;
> +				};
> +
> +				opp-465000000 {
> +					opp-hz = /bits/ 64 <465000000>;
> +				};
> +
> +				opp-400000000 {
> +					opp-hz = /bits/ 64 <400000000>;
> +				};
> +
> +				opp-220000000 {
> +					opp-hz = /bits/ 64 <220000000>;
> +				};
> +
> +				opp-19200000 {
> +					opp-hz = /bits/ 64 <19200000>;
> +				};
> +			};
> +		};
> +
> +		apps_iommu: iommu@1ef0000 {
> +			compatible = "qcom,msm8916-iommu", "qcom,msm-iommu-v1";
> +			reg = <0x01ef0000 0x3000>;
> +			ranges = <0 0x1e20000 0x40000>;
> +			clocks = <&gcc GCC_SMMU_CFG_CLK>,
> +				 <&gcc GCC_APSS_TCU_CLK>;
> +			clock-names = "iface", "bus";
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			#iommu-cells = <1>;
> +			qcom,iommu-secure-id = <17>;
> +
> +			/* mdp_0: */
> +			iommu-ctx@4000 {
> +				compatible = "qcom,msm-iommu-v1-ns";
> +				reg = <0x4000 0x1000>;
> +				interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>;
> +			};
> +
> +			/* venus_ns: */
> +			iommu-ctx@5000 {
> +				compatible = "qcom,msm-iommu-v1-sec";
> +				reg = <0x5000 0x1000>;
> +				interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
> +			};
> +		};
> +
> +		gpu_iommu: iommu@1f08000 {
> +			compatible = "qcom,msm8916-iommu", "qcom,msm-iommu-v1";
> +			ranges = <0 0x1f08000 0x10000>;
> +			clocks = <&gcc GCC_SMMU_CFG_CLK>,
> +				 <&gcc GCC_GFX_TCU_CLK>,
> +				 <&gcc GCC_GFX_TBU_CLK>;
> +			clock-names = "iface", "bus", "tbu";
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			#iommu-cells = <1>;
> +			qcom,iommu-secure-id = <18>;
> +
> +			/* gfx3d_user: */
> +			iommu-ctx@1000 {
> +				compatible = "qcom,msm-iommu-v1-ns";
> +				reg = <0x1000 0x1000>;
> +				interrupts = <GIC_SPI 241 IRQ_TYPE_LEVEL_HIGH>;
> +			};
> +
> +			/* gfx3d_priv: */
> +			iommu-ctx@2000 {
> +				compatible = "qcom,msm-iommu-v1-ns";
> +				reg = <0x2000 0x1000>;
> +				interrupts = <GIC_SPI 242 IRQ_TYPE_LEVEL_HIGH>;
> +			};
> +		};
> +
> +		spmi_bus: spmi@200f000 {
> +			compatible = "qcom,spmi-pmic-arb";
> +			reg = <0x0200f000 0x001000>,
> +			      <0x02400000 0x400000>,
> +			      <0x02c00000 0x400000>,
> +			      <0x03800000 0x200000>,
> +			      <0x0200a000 0x002100>;
> +			reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
> +			interrupt-names = "periph_irq";
> +			interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>;
> +			qcom,ee = <0>;
> +			qcom,channel = <0>;
> +			#address-cells = <2>;
> +			#size-cells = <0>;
> +			interrupt-controller;
> +			#interrupt-cells = <4>;
> +		};
> +
> +		mpss: remoteproc@4080000 {
> +			compatible = "qcom,msm8916-mss-pil";
> +			reg = <0x04080000 0x100>,
> +			      <0x04020000 0x040>;
> +
> +			reg-names = "qdsp6", "rmb";
> +
> +			interrupts-extended = <&intc GIC_SPI 24 IRQ_TYPE_EDGE_RISING>,
> +					      <&hexagon_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
> +					      <&hexagon_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
> +					      <&hexagon_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
> +					      <&hexagon_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
> +			interrupt-names = "wdog", "fatal", "ready",
> +					  "handover", "stop-ack";
> +
> +			clocks = <&gcc GCC_MSS_CFG_AHB_CLK>,
> +				 <&gcc GCC_MSS_Q6_BIMC_AXI_CLK>,
> +				 <&gcc GCC_BOOT_ROM_AHB_CLK>,
> +				 <&xo_board>;
> +			clock-names = "iface", "bus", "mem", "xo";
> +
> +			power-domains = <&rpmpd MSM8939_VDDMDCX>,
> +					<&rpmpd MSM8939_VDDMX>;
> +			power-domain-names = "cx", "mx";
> +
> +			qcom,smem-states = <&hexagon_smp2p_out 0>;
> +			qcom,smem-state-names = "stop";
> +
> +			resets = <&scm 0>;
> +			reset-names = "mss_restart";
> +
> +			qcom,halt-regs = <&tcsr 0x18000 0x19000 0x1a000>;
> +
> +			status = "disabled";
> +
> +			mba {
> +				memory-region = <&mba_mem>;
> +			};
> +
> +			mpss {
> +				memory-region = <&mpss_mem>;
> +			};
> +
> +			smd-edge {
> +				interrupts = <GIC_SPI 25 IRQ_TYPE_EDGE_RISING>;
> +
> +				qcom,smd-edge = <0>;
> +				mboxes = <&apcs1_mbox 12>;
> +				qcom,remote-pid = <1>;
> +
> +				label = "hexagon";
> +			};
> +		};
> +
> +		sound: sound@7702000 {
> +			compatible = "qcom,apq8016-sbc-sndcard";
> +			reg = <0x07702000 0x4>,
> +			      <0x07702004 0x4>;
> +			reg-names = "mic-iomux", "spkr-iomux";
> +			status = "disabled";
> +		};
> +
> +		lpass: audio-controller@7708000 {
> +			compatible = "qcom,apq8016-lpass-cpu";
> +			reg = <0x07708000 0x10000>;
> +			reg-names = "lpass-lpaif";
> +			interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>;
> +			interrupt-names = "lpass-irq-lpaif";
> +			clocks = <&gcc GCC_ULTAUDIO_AHBFABRIC_IXFABRIC_CLK>,
> +				 <&gcc GCC_ULTAUDIO_LPAIF_PRI_I2S_CLK>,
> +				 <&gcc GCC_ULTAUDIO_LPAIF_PRI_I2S_CLK>,
> +				 <&gcc GCC_ULTAUDIO_LPAIF_SEC_I2S_CLK>,
> +				 <&gcc GCC_ULTAUDIO_LPAIF_AUX_I2S_CLK>,
> +				 <&gcc GCC_ULTAUDIO_PCNOC_MPORT_CLK>,
> +				 <&gcc GCC_ULTAUDIO_PCNOC_SWAY_CLK>;
> +			clock-names = "ahbix-clk",
> +				      "mi2s-bit-clk0",
> +				      "mi2s-bit-clk1",
> +				      "mi2s-bit-clk2",
> +				      "mi2s-bit-clk3",
> +				      "pcnoc-mport-clk",
> +				      "pcnoc-sway-clk";
> +			#sound-dai-cells = <1>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			status = "disabled";
> +		};
> +
> +		lpass_codec: audio-codec@771c000 {
> +			compatible = "qcom,msm8916-wcd-digital-codec";
> +			reg = <0x0771c000 0x400>;
> +			clocks = <&gcc GCC_ULTAUDIO_AHBFABRIC_IXFABRIC_CLK>,
> +				 <&gcc GCC_CODEC_DIGCODEC_CLK>;
> +			clock-names = "ahbix-clk", "mclk";
> +			#sound-dai-cells = <1>;
> +		};
> +
> +		blsp_dma: dma-controller@7884000 {
> +			compatible = "qcom,bam-v1.7.0";
> +			reg = <0x07884000 0x23000>;
> +			interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&gcc GCC_BLSP1_AHB_CLK>;
> +			clock-names = "bam_clk";
> +			#dma-cells = <1>;
> +			qcom,ee = <0>;
> +			status = "disabled";
> +		};
> +
> +		blsp1_uart1: serial@78af000 {
> +			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
> +			reg = <0x078af000 0x200>;
> +			interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
> +			clock-names = "core", "iface";
> +			dmas = <&blsp_dma 0>, <&blsp_dma 1>;
> +			dma-names = "tx", "rx";
> +			pinctrl-names = "default", "sleep";
> +			pinctrl-0 = <&blsp1_uart1_default>;
> +			pinctrl-1 = <&blsp1_uart1_sleep>;
> +			status = "disabled";
> +		};
> +
> +		blsp1_uart2: serial@78b0000 {
> +			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
> +			reg = <0x078b0000 0x200>;
> +			interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
> +			clock-names = "core", "iface";
> +			dmas = <&blsp_dma 2>, <&blsp_dma 3>;
> +			dma-names = "tx", "rx";
> +			pinctrl-names = "default", "sleep";
> +			pinctrl-0 = <&blsp1_uart2_default>;
> +			pinctrl-1 = <&blsp1_uart2_sleep>;
> +			status = "disabled";
> +		};
> +
> +		blsp_i2c1: i2c@78b5000 {
> +			compatible = "qcom,i2c-qup-v2.2.1";
> +			reg = <0x078b5000 0x500>;
> +			interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>,
> +				 <&gcc GCC_BLSP1_AHB_CLK>;
> +			clock-names = "core", "iface";
> +			dmas = <&blsp_dma 4>, <&blsp_dma 5>;
> +			dma-names = "tx", "rx";
> +			pinctrl-names = "default", "sleep";
> +			pinctrl-0 = <&i2c1_default>;
> +			pinctrl-1 = <&i2c1_sleep>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			status = "disabled";
> +		};
> +
> +		blsp_i2c2: i2c@78b6000 {
> +			compatible = "qcom,i2c-qup-v2.2.1";
> +			reg = <0x078b6000 0x500>;
> +			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>,
> +				 <&gcc GCC_BLSP1_AHB_CLK>;
> +			clock-names =  "core", "iface";
> +			dmas = <&blsp_dma 6>, <&blsp_dma 7>;
> +			dma-names = "tx", "rx";
> +			pinctrl-names = "default", "sleep";
> +			pinctrl-0 = <&i2c2_default>;
> +			pinctrl-1 = <&i2c2_sleep>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			status = "disabled";
> +		};
> +
> +		blsp_i2c3: i2c@78b7000 {
> +			compatible = "qcom,i2c-qup-v2.2.1";
> +			reg = <0x078b7000 0x500>;
> +			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>,
> +				 <&gcc GCC_BLSP1_AHB_CLK>;
> +			clock-names =  "core", "iface";
> +			dmas = <&blsp_dma 8>, <&blsp_dma 9>;
> +			dma-names = "tx", "rx";
> +			pinctrl-names = "default", "sleep";
> +			pinctrl-0 = <&i2c3_default>;
> +			pinctrl-1 = <&i2c3_sleep>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			status = "disabled";
> +		};
> +
> +		blsp_i2c4: i2c@78b8000 {
> +			compatible = "qcom,i2c-qup-v2.2.1";
> +			reg = <0x078b8000 0x500>;
> +			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>,
> +				 <&gcc GCC_BLSP1_AHB_CLK>;
> +			clock-names =  "core", "iface";
> +			dmas = <&blsp_dma 10>, <&blsp_dma 11>;
> +			dma-names = "tx", "rx";
> +			pinctrl-names = "default", "sleep";
> +			pinctrl-0 = <&i2c4_default>;
> +			pinctrl-1 = <&i2c4_sleep>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			status = "disabled";
> +		};
> +
> +		blsp_i2c5: i2c@78b9000 {
> +			compatible = "qcom,i2c-qup-v2.2.1";
> +			reg = <0x078b9000 0x500>;
> +			interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&gcc GCC_BLSP1_QUP5_I2C_APPS_CLK>,
> +				 <&gcc GCC_BLSP1_AHB_CLK>;
> +			clock-names =  "core", "iface";
> +			dmas = <&blsp_dma 12>, <&blsp_dma 13>;
> +			dma-names = "tx", "rx";
> +			pinctrl-names = "default", "sleep";
> +			pinctrl-0 = <&i2c5_default>;
> +			pinctrl-1 = <&i2c5_sleep>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			status = "disabled";
> +		};
> +
> +		blsp_i2c6: i2c@78ba000 {
> +			compatible = "qcom,i2c-qup-v2.2.1";
> +			reg = <0x078ba000 0x500>;
> +			interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&gcc GCC_BLSP1_QUP6_I2C_APPS_CLK>,
> +				 <&gcc GCC_BLSP1_AHB_CLK>;
> +			clock-names =  "core", "iface";
> +			dmas = <&blsp_dma 14>, <&blsp_dma 15>;
> +			dma-names = "tx", "rx";
> +			pinctrl-names = "default", "sleep";
> +			pinctrl-0 = <&i2c6_default>;
> +			pinctrl-1 = <&i2c6_sleep>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			status = "disabled";
> +		};
> +
> +		blsp_spi1: spi@78b5000 {
> +			compatible = "qcom,spi-qup-v2.2.1";
> +			reg = <0x078b5000 0x500>;
> +			interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&gcc GCC_BLSP1_QUP1_SPI_APPS_CLK>,
> +				 <&gcc GCC_BLSP1_AHB_CLK>;
> +			clock-names = "core", "iface";
> +			dmas = <&blsp_dma 4>, <&blsp_dma 5>;
> +			dma-names = "tx", "rx";
> +			pinctrl-names = "default", "sleep";
> +			pinctrl-0 = <&spi1_default>;
> +			pinctrl-1 = <&spi1_sleep>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			status = "disabled";
> +		};
> +
> +		blsp_spi2: spi@78b6000 {
> +			compatible = "qcom,spi-qup-v2.2.1";
> +			reg = <0x078b6000 0x500>;
> +			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&gcc GCC_BLSP1_QUP2_SPI_APPS_CLK>,
> +				 <&gcc GCC_BLSP1_AHB_CLK>;
> +			clock-names = "core", "iface";
> +			dmas = <&blsp_dma 6>, <&blsp_dma 7>;
> +			dma-names = "tx", "rx";
> +			pinctrl-names = "default", "sleep";
> +			pinctrl-0 = <&spi2_default>;
> +			pinctrl-1 = <&spi2_sleep>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			status = "disabled";
> +		};
> +
> +		blsp_spi3: spi@78b7000 {
> +			compatible = "qcom,spi-qup-v2.2.1";
> +			reg = <0x078b7000 0x500>;
> +			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&gcc GCC_BLSP1_QUP3_SPI_APPS_CLK>,
> +				 <&gcc GCC_BLSP1_AHB_CLK>;
> +			clock-names = "core", "iface";
> +			dmas = <&blsp_dma 8>, <&blsp_dma 9>;
> +			dma-names = "tx", "rx";
> +			pinctrl-names = "default", "sleep";
> +			pinctrl-0 = <&spi3_default>;
> +			pinctrl-1 = <&spi3_sleep>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			status = "disabled";
> +		};
> +
> +		blsp_spi4: spi@78b8000 {
> +			compatible = "qcom,spi-qup-v2.2.1";
> +			reg = <0x078b8000 0x500>;
> +			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&gcc GCC_BLSP1_QUP4_SPI_APPS_CLK>,
> +				 <&gcc GCC_BLSP1_AHB_CLK>;
> +			clock-names = "core", "iface";
> +			dmas = <&blsp_dma 10>, <&blsp_dma 11>;
> +			dma-names = "tx", "rx";
> +			pinctrl-names = "default", "sleep";
> +			pinctrl-0 = <&spi4_default>;
> +			pinctrl-1 = <&spi4_sleep>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			status = "disabled";
> +		};
> +
> +		blsp_spi5: spi@78b9000 {
> +			compatible = "qcom,spi-qup-v2.2.1";
> +			reg = <0x078b9000 0x500>;
> +			interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&gcc GCC_BLSP1_QUP5_SPI_APPS_CLK>,
> +				 <&gcc GCC_BLSP1_AHB_CLK>;
> +			clock-names = "core", "iface";
> +			dmas = <&blsp_dma 12>, <&blsp_dma 13>;
> +			dma-names = "tx", "rx";
> +			pinctrl-names = "default", "sleep";
> +			pinctrl-0 = <&spi5_default>;
> +			pinctrl-1 = <&spi5_sleep>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			status = "disabled";
> +		};
> +
> +		blsp_spi6: spi@78ba000 {
> +			compatible = "qcom,spi-qup-v2.2.1";
> +			reg = <0x078ba000 0x500>;
> +			interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&gcc GCC_BLSP1_QUP6_SPI_APPS_CLK>,
> +				 <&gcc GCC_BLSP1_AHB_CLK>;
> +			clock-names = "core", "iface";
> +			dmas = <&blsp_dma 14>, <&blsp_dma 15>;
> +			dma-names = "tx", "rx";
> +			pinctrl-names = "default", "sleep";
> +			pinctrl-0 = <&spi6_default>;
> +			pinctrl-1 = <&spi6_sleep>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			status = "disabled";
> +		};
> +
> +		sdhc_1: mmc@7824000 {
> +			compatible = "qcom,msm8916-sdhci", "qcom,sdhci-msm-v4";
> +			reg = <0x07824900 0x11c>,
> +			      <0x07824000 0x800>;
> +			reg-names = "hc", "core";
> +
> +			interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, <0 138 IRQ_TYPE_LEVEL_HIGH>;
> +			interrupt-names = "hc_irq", "pwr_irq";
> +			clocks = <&gcc GCC_SDCC1_AHB_CLK>,
> +				 <&gcc GCC_SDCC1_APPS_CLK>,
> +				 <&xo_board>;
> +			clock-names = "iface", "core", "xo";
> +			resets = <&gcc GCC_SDCC1_BCR>;
> +			mmc-ddr-1_8v;
> +			bus-width = <8>;
> +			non-removable;
> +			status = "disabled";
> +		};
> +
> +		sdhc_2: mmc@7864000 {
> +			compatible = "qcom,msm8916-sdhci", "qcom,sdhci-msm-v4";
> +			reg = <0x07864900 0x11c>,
> +			      <0x07864000 0x800>;
> +			reg-names = "hc", "core";
> +
> +			interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>, <0 221 IRQ_TYPE_LEVEL_HIGH>;
> +			interrupt-names = "hc_irq", "pwr_irq";
> +			clocks = <&gcc GCC_SDCC2_AHB_CLK>,
> +				 <&gcc GCC_SDCC2_APPS_CLK>,
> +				 <&xo_board>;
> +			clock-names =  "iface", "core", "xo";
> +			resets = <&gcc GCC_SDCC2_BCR>;
> +			bus-width = <4>;
> +			status = "disabled";
> +		};
> +
> +		usb: usb@78d9000 {
> +			compatible = "qcom,ci-hdrc";
> +			reg = <0x078d9000 0x200>,
> +			      <0x078d9200 0x200>;
> +			interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&gcc GCC_USB_HS_AHB_CLK>,
> +				 <&gcc GCC_USB_HS_SYSTEM_CLK>;
> +			clock-names = "iface", "core";
> +			assigned-clocks = <&gcc GCC_USB_HS_SYSTEM_CLK>;
> +			assigned-clock-rates = <80000000>;
> +			resets = <&gcc GCC_USB_HS_BCR>;
> +			reset-names = "core";
> +			#reset-cells = <1>;
> +			phy_type = "ulpi";
> +			dr_mode = "otg";
> +			ahb-burst-config = <0>;
> +			phy-names = "usb-phy";
> +			phys = <&usb_hs_phy>;
> +			status = "disabled";
> +
> +			ulpi {
> +				usb_hs_phy: phy {
> +					compatible = "qcom,usb-hs-phy-msm8916",
> +						     "qcom,usb-hs-phy";
> +					clocks = <&xo_board>, <&gcc GCC_USB2A_PHY_SLEEP_CLK>;
> +					clock-names = "ref", "sleep";
> +					resets = <&gcc GCC_USB2A_PHY_BCR>, <&usb 0>;
> +					reset-names = "phy", "por";
> +					#phy-cells = <0>;
> +					qcom,init-seq = /bits/ 8 <0x0 0x44
> +						0x1 0x6b 0x2 0x24 0x3 0x13>;
> +				};
> +			};
> +		};
> +
> +		intc: interrupt-controller@b000000 {
> +			compatible = "qcom,msm-qgic2";
> +			reg = <0x0b000000 0x1000>, <0x0b002000 0x2000>,
> +			      <0x0b001000 0x1000>, <0x0b004000 0x2000>;
> +			interrupt-controller;
> +			#interrupt-cells = <3>;
> +			interrupts = <GIC_PPI 0 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>;
> +		};
> +
> +		apcs1_mbox: mailbox@b011000 {
> +			compatible = "qcom,msm8939-apcs-kpss-global", "syscon";
> +			reg = <0x0b011000 0x1000>;
> +			clocks = <&a53pll_c1>, <&gcc GPLL0_VOTE>, <&xo_board>;
> +			clock-names = "pll", "aux", "ref";
> +			#clock-cells = <0>;
> +			assigned-clocks = <&apcs2>;
> +			assigned-clock-rates = <297600000>;
> +			#mbox-cells = <1>;
> +		};
> +
> +		a53pll_c1: clock@b016000 {
> +			compatible = "qcom,msm8939-a53pll";
> +			reg = <0x0b016000 0x40>;
> +			#clock-cells = <0>;
> +		};
> +
> +		acc0: clock-controller@b088000 {
> +			compatible = "qcom,kpss-acc-v2";
> +			reg = <0x0b088000 0x1000>;
> +		};
> +
> +		saw0: power-manager@b089000 {
> +			compatible = "qcom,msm8939-saw2-v3.0-cpu", "qcom,saw2";
> +			reg = <0x0b089000 0x1000>;
> +		};
> +
> +		acc1: clock-controller@b098000 {
> +			compatible = "qcom,kpss-acc-v2";
> +			reg = <0x0b098000 0x1000>;
> +		};
> +
> +		saw1: power-manager@b099000 {
> +			compatible = "qcom,msm8939-saw2-v3.0-cpu", "qcom,saw2";
> +			reg = <0x0b099000 0x1000>;
> +		};
> +
> +		acc2: clock-controller@b0a8000 {
> +			compatible = "qcom,kpss-acc-v2";
> +			reg = <0x0b0a8000 0x1000>;
> +		};
> +
> +		saw2: power-manager@b0a9000 {
> +			compatible = "qcom,msm8939-saw2-v3.0-cpu", "qcom,saw2";
> +			reg = <0x0b0a9000 0x1000>;
> +		};
> +
> +		acc3: clock-controller@b0b8000 {
> +			compatible = "qcom,kpss-acc-v2";
> +			reg = <0x0b0b8000 0x1000>;
> +		};
> +
> +		saw3: power-manager@b0b9000 {
> +			compatible = "qcom,msm8939-saw2-v3.0-cpu", "qcom,saw2";
> +			reg = <0x0b0b9000 0x1000>;
> +		};
> +
> +		apcs0_mbox: mailbox@b111000 {
> +			compatible = "qcom,msm8939-apcs-kpss-global", "syscon";
> +			reg = <0x0b111000 0x1000>;
> +			clocks = <&a53pll_c0>, <&gcc GPLL0_VOTE>, <&xo_board>;
> +			clock-names = "pll", "aux", "ref";
> +			#clock-cells = <0>;
> +			#mbox-cells = <1>;
> +		};
> +
> +		a53pll_c0: clock@b116000 {
> +			compatible = "qcom,msm8939-a53pll";
> +			reg = <0x0b116000 0x40>;
> +			#clock-cells = <0>;
> +		};
> +
> +		acc4: clock-controller@b188000 {
> +			compatible = "qcom,kpss-acc-v2";
> +			reg = <0x0b188000 0x1000>;
> +		};
> +
> +		saw4: power-manager@b189000 {
> +			compatible = "qcom,msm8939-saw2-v3.0-cpu", "qcom,saw2";
> +			reg = <0x0b189000 0x1000>;
> +		};
> +
> +		acc5: clock-controller@b198000 {
> +			compatible = "qcom,kpss-acc-v2";
> +			reg = <0x0b198000 0x1000>;
> +		};
> +
> +		saw5: power-manager@b199000 {
> +			compatible = "qcom,msm8939-saw2-v3.0-cpu", "qcom,saw2";
> +			reg = <0x0b199000 0x1000>;
> +		};
> +
> +		acc6: clock-controller@b1a8000 {
> +			compatible = "qcom,kpss-acc-v2";
> +			reg = <0x0b1a8000 0x1000>;
> +		};
> +
> +		saw6: power-manager@b1a9000 {
> +			compatible = "qcom,msm8939-saw2-v3.0-cpu", "qcom,saw2";
> +			reg = <0x0b1a9000 0x1000>;
> +		};
> +
> +		acc7: clock-controller@b1b8000 {
> +			compatible = "qcom,kpss-acc-v2";
> +			reg = <0x0b1b8000 0x1000>;
> +		};
> +
> +		saw7: power-manager@b1b9000 {
> +			compatible = "qcom,msm8939-saw2-v3.0-cpu", "qcom,saw2";
> +			reg = <0x0b1b9000 0x1000>;
> +		};
> +
> +		a53pll_cci: clock@b1d0000 {
> +			compatible = "qcom,msm8939-a53pll";
> +			reg = <0x0b1d0000 0x40>;
> +			#clock-cells = <0>;
> +		};
> +
> +		apcs2: mailbox@b1d1000 {
> +			compatible = "qcom,msm8939-apcs-kpss-global", "syscon";
> +			reg = <0x0b1d1000 0x1000>;
> +			clocks = <&a53pll_cci>, <&gcc GPLL0_VOTE>, <&xo_board>;
> +			clock-names = "pll", "aux", "ref";
> +			#clock-cells = <0>;
> +			#mbox-cells = <1>;
> +		};
> +
> +		timer@b020000 {
> +			compatible = "arm,armv7-timer-mem";
> +			reg = <0x0b020000 0x1000>;
> +			clock-frequency = <19200000>;
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			ranges;
> +
> +			frame@b021000 {
> +				frame-number = <0>;
> +				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
> +					     <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
> +				reg = <0x0b021000 0x1000>,
> +				      <0x0b022000 0x1000>;
> +			};
> +
> +			frame@b023000 {
> +				frame-number = <1>;
> +				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
> +				reg = <0x0b023000 0x1000>;
> +				status = "disabled";
> +			};
> +
> +			frame@b024000 {
> +				frame-number = <2>;
> +				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
> +				reg = <0x0b024000 0x1000>;
> +				status = "disabled";
> +			};
> +
> +			frame@b025000 {
> +				frame-number = <3>;
> +				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
> +				reg = <0x0b025000 0x1000>;
> +				status = "disabled";
> +			};
> +
> +			frame@b026000 {
> +				frame-number = <4>;
> +				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
> +				reg = <0x0b026000 0x1000>;
> +				status = "disabled";
> +			};
> +
> +			frame@b027000 {
> +				frame-number = <5>;
> +				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
> +				reg = <0x0b027000 0x1000>;
> +				status = "disabled";
> +			};
> +
> +			frame@b028000 {
> +				frame-number = <6>;
> +				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
> +				reg = <0x0b028000 0x1000>;
> +				status = "disabled";
> +			};
> +		};
> +
> +		pronto: remoteproc@a204000 {
> +			compatible = "qcom,pronto-v2-pil", "qcom,pronto";
> +			reg = <0x0a204000 0x2000>,
> +			      <0x0a202000 0x1000>,
> +			      <0x0a21b000 0x3000>;
> +			reg-names = "ccu", "dxe", "pmu";
> +
> +			interrupts-extended = <&intc 0 149 IRQ_TYPE_EDGE_RISING>,
> +					      <&wcnss_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
> +					      <&wcnss_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
> +					      <&wcnss_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
> +					      <&wcnss_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
> +			interrupt-names = "wdog", "fatal", "ready", "handover", "stop-ack";
> +
> +			memory-region = <&wcnss_mem>;
> +
> +			power-domains = <&rpmpd MSM8939_VDDCX>,
> +					<&rpmpd MSM8939_VDDMX_AO>;
> +			power-domain-names = "cx", "mx";
> +
> +			qcom,smem-states = <&wcnss_smp2p_out 0>;
> +			qcom,smem-state-names = "stop";
> +
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&wcnss_pin_a>;
> +
> +			status = "disabled";
> +
> +			iris {
> +				compatible = "qcom,wcn3620";
> +
> +				clocks = <&rpmcc RPM_SMD_RF_CLK2>;
> +				clock-names = "xo";
> +			};
> +
> +			smd-edge {
> +				interrupts = <GIC_SPI 142 1>;
> +
> +				qcom,ipc = <&apcs1_mbox 8 17>;
> +				qcom,smd-edge = <6>;
> +				qcom,remote-pid = <4>;
> +
> +				label = "pronto";
> +
> +				wcnss {
> +					compatible = "qcom,wcnss";
> +					qcom,smd-channels = "WCNSS_CTRL";
> +
> +					qcom,mmio = <&pronto>;
> +
> +					bluetooth {
> +						compatible = "qcom,wcnss-bt";
> +					};
> +
> +					wifi {
> +						compatible = "qcom,wcnss-wlan";
> +
> +						interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>,
> +							     <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>;
> +						interrupt-names = "tx", "rx";
> +
> +						qcom,smem-states = <&apps_smsm 10>,
> +								   <&apps_smsm 9>;
> +						qcom,smem-state-names = "tx-enable",
> +									"tx-rings-empty";
> +					};
> +				};
> +			};
> +		};
> +	};
> +
> +	smd {
> +		compatible = "qcom,smd";
> +
> +		rpm {
> +			interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>;
> +			qcom,ipc = <&apcs1_mbox 8 0>;
> +			qcom,smd-edge = <15>;
> +
> +			rpm_requests: rpm-requests {
> +				compatible = "qcom,rpm-msm8936";
> +				qcom,smd-channels = "rpm_requests";
> +
> +				rpmcc: clock-controller {
> +					compatible = "qcom,rpmcc-msm8936", "qcom,rpmcc";
> +					#clock-cells = <1>;
> +				};
> +
> +				rpmpd: power-controller {
> +					compatible = "qcom,msm8939-rpmpd";
> +					#power-domain-cells = <1>;
> +					operating-points-v2 = <&rpmpd_opp_table>;
> +
> +					rpmpd_opp_table: opp-table {
> +						compatible = "operating-points-v2";
> +
> +						rpmpd_opp_ret: opp1 {
> +							opp-level = <1>;
> +						};
> +
> +						rpmpd_opp_svs_krait: opp2 {
> +							opp-level = <2>;
> +						};
> +
> +						rpmpd_opp_svs_soc: opp3 {
> +							opp-level = <3>;
> +						};
> +
> +						rpmpd_opp_nom: opp4 {
> +							opp-level = <4>;
> +						};
> +
> +						rpmpd_opp_turbo: opp5 {
> +							opp-level = <5>;
> +						};
> +
> +						rpmpd_opp_super_turbo: opp6 {
> +							opp-level = <6>;
> +						};
> +					};
> +				};
> +			};
> +		};
> +	};
> +
> +	thermal_zones: thermal-zones {
> +		cpu0-thermal {
> +			polling-delay-passive = <250>;
> +			polling-delay = <1000>;
> +
> +			thermal-sensors = <&tsens 5>;
> +
> +			trips {
> +				cpu0_alert: trip0 {
> +					temperature = <75000>;
> +					hysteresis = <2000>;
> +					type = "passive";
> +				};
> +				cpu0_crit: trip1 {
> +					temperature = <115000>;
> +					hysteresis = <0>;
> +					type = "critical";
> +				};
> +			};
> +
> +			cooling-maps {
> +				map0 {
> +					trip = <&cpu0_alert>;
> +					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> +				};
> +			};
> +		};
> +
> +		cpu1-thermal {
> +			polling-delay-passive = <250>;
> +			polling-delay = <1000>;
> +
> +			thermal-sensors = <&tsens 6>;
> +
> +			trips {
> +				cpu1_alert: trip0 {
> +					temperature = <75000>;
> +					hysteresis = <2000>;
> +					type = "passive";
> +				};
> +				cpu1_crit: trip1 {
> +					temperature = <110000>;
> +					hysteresis = <2000>;
> +					type = "critical";
> +				};
> +			};
> +
> +			cooling-maps {
> +				map0 {
> +					trip = <&cpu1_alert>;
> +					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> +				};
> +			};
> +		};
> +
> +		cpu2-thermal {
> +			polling-delay-passive = <250>;
> +			polling-delay = <1000>;
> +
> +			thermal-sensors = <&tsens 7>;
> +
> +			trips {
> +				cpu2_alert: trip0 {
> +					temperature = <75000>;
> +					hysteresis = <2000>;
> +					type = "passive";
> +				};
> +				cpu2_crit: trip1 {
> +					temperature = <110000>;
> +					hysteresis = <2000>;
> +					type = "critical";
> +				};
> +			};
> +
> +			cooling-maps {
> +				map0 {
> +					trip = <&cpu2_alert>;
> +					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> +				};
> +			};
> +		};
> +
> +		cpu3-thermal {
> +			polling-delay-passive = <250>;
> +			polling-delay = <1000>;
> +
> +			thermal-sensors = <&tsens 8>;
> +
> +			trips {
> +				cpu3_alert: trip0 {
> +					temperature = <75000>;
> +					hysteresis = <2000>;
> +					type = "passive";
> +				};
> +				cpu3_crit: trip1 {
> +					temperature = <110000>;
> +					hysteresis = <2000>;
> +					type = "critical";
> +				};
> +			};
> +
> +			cooling-maps {
> +				map0 {
> +					trip = <&cpu3_alert>;
> +					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> +				};
> +			};
> +		};
> +
> +		cpu4567-thermal {
> +			polling-delay-passive = <250>;
> +			polling-delay = <1000>;
> +
> +			thermal-sensors = <&tsens 9>;
> +
> +			trips {
> +				cpu4567_alert: trip0 {
> +					temperature = <75000>;
> +					hysteresis = <2000>;
> +					type = "passive";
> +				};
> +				cpu4567_crit: trip1 {
> +					temperature = <110000>;
> +					hysteresis = <2000>;
> +					type = "critical";
> +				};
> +			};
> +
> +			cooling-maps {
> +				map0 {
> +					trip = <&cpu4567_alert>;
> +					cooling-device = <&cpu4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +							 <&cpu5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +							 <&cpu6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +							 <&cpu7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> +				};
> +			};
> +		};
> +
> +		gpu-thermal {
> +			polling-delay-passive = <250>;
> +			polling-delay = <1000>;
> +
> +			thermal-sensors = <&tsens 3>;
> +
> +			trips {
> +				gpu_alert0: trip-point0 {
> +					temperature = <75000>;
> +					hysteresis = <2000>;
> +					type = "passive";
> +				};
> +				gpu_crit: gpu_crit {
> +					temperature = <95000>;
> +					hysteresis = <2000>;
> +					type = "critical";
> +				};
> +			};
> +		};
> +
> +		modem1-thermal {
> +			polling-delay-passive = <250>;
> +			polling-delay = <1000>;
> +
> +			thermal-sensors = <&tsens 0>;
> +
> +			trips {
> +				modem1_alert0: trip-point0 {
> +					temperature = <85000>;
> +					hysteresis = <2000>;
> +					type = "hot";
> +				};
> +			};
> +		};
> +
> +		modem2-thermal {
> +			polling-delay-passive = <250>;
> +			polling-delay = <1000>;
> +
> +			thermal-sensors = <&tsens 2>;
> +
> +			trips {
> +				modem2_alert0: trip-point0 {
> +					temperature = <85000>;
> +					hysteresis = <2000>;
> +					type = "hot";
> +				};
> +			};
> +		};
> +
> +		camera-thermal {
> +			polling-delay-passive = <250>;
> +			polling-delay = <1000>;
> +
> +			thermal-sensors = <&tsens 1>;
> +
> +			trips {
> +				cam_alert0: trip-point0 {
> +					temperature = <75000>;
> +					hysteresis = <2000>;
> +					type = "hot";
> +				};
> +			};
> +		};
> +	};
> +
> +	timer {
> +		compatible = "arm,armv8-timer";
> +		interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
> +			     <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
> +			     <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
> +			     <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
> +	};
> +
> +	vreg_dummy: regulator-dummy {
> +		#power-domain-cells = <0>;
> +	};
> +
> +	wcnss-smp2p {
> +		compatible = "qcom,smp2p";
> +		qcom,smem = <451>, <431>;
> +
> +		interrupts = <GIC_SPI 143 IRQ_TYPE_EDGE_RISING>;
> +
> +		mboxes = <&apcs1_mbox 18>;
> +
> +		qcom,local-pid = <0>;
> +		qcom,remote-pid = <4>;
> +
> +		wcnss_smp2p_out: master-kernel {
> +			qcom,entry-name = "master-kernel";
> +
> +			#qcom,smem-state-cells = <1>;
> +		};
> +
> +		wcnss_smp2p_in: slave-kernel {
> +			qcom,entry-name = "slave-kernel";
> +
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +		};
> +	};
> +};