Re: [PATCH v2] ARM: dts: qcom: apq8026-samsung-matisse-wifi: Add display backlight

[Konrad Dybcio]

On 11.01.2023 19:35, Matti Lehtimäki wrote:
> Uses ti,lp8556 backlight with clk-pwm.
> 
> Signed-off-by: Matti Lehtimäki <matti.lehtimaki@xxxxxxxxx>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio@xxxxxxxxxx>

Konrad
> This patch was part of the series
> https://lore.kernel.org/linux-arm-msm/20230106114403.275865-1-matti.lehtimaki@xxxxxxxxx/
> which already had the other patches applied.
> 
> Changes in v2:
>   - Add empty line between subnodes
>   - Move pwm node to correct place
>   - Reorder pinctrl properties
> ---
>  .../dts/qcom-apq8026-samsung-matisse-wifi.dts | 61 +++++++++++++++++++
>  1 file changed, 61 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/qcom-apq8026-samsung-matisse-wifi.dts b/arch/arm/boot/dts/qcom-apq8026-samsung-matisse-wifi.dts
> index 15b9590ba07b..91b860e24681 100644
> --- a/arch/arm/boot/dts/qcom-apq8026-samsung-matisse-wifi.dts
> +++ b/arch/arm/boot/dts/qcom-apq8026-samsung-matisse-wifi.dts
> @@ -80,6 +80,55 @@ key-volume-up {
>  		};
>  	};
>  
> +	i2c-backlight {
> +		compatible = "i2c-gpio";
> +		sda-gpios = <&tlmm 20 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
> +		scl-gpios = <&tlmm 21 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
> +
> +		pinctrl-0 = <&backlight_i2c_default_state>;
> +		pinctrl-names = "default";
> +
> +		i2c-gpio,delay-us = <4>;
> +
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		backlight@2c {
> +			compatible = "ti,lp8556";
> +			reg = <0x2c>;
> +
> +			dev-ctrl = /bits/ 8 <0x80>;
> +			init-brt = /bits/ 8 <0x3f>;
> +			pwm-period = <100000>;
> +
> +			pwms = <&backlight_pwm 0 100000>;
> +			pwm-names = "lp8556";
> +
> +			rom-a0h {
> +				rom-addr = /bits/ 8 <0xa0>;
> +				rom-val = /bits/ 8 <0x44>;
> +			};
> +
> +			rom-a1h {
> +				rom-addr = /bits/ 8 <0xa1>;
> +				rom-val = /bits/ 8 <0x6c>;
> +			};
> +
> +			rom-a5h {
> +				rom-addr = /bits/ 8 <0xa5>;
> +				rom-val = /bits/ 8 <0x24>;
> +			};
> +		};
> +	};
> +
> +	backlight_pwm: pwm {
> +		compatible = "clk-pwm";
> +		#pwm-cells = <2>;
> +		clocks = <&mmcc CAMSS_GP0_CLK>;
> +		pinctrl-0 = <&backlight_pwm_default_state>;
> +		pinctrl-names = "default";
> +	};
> +
>  	reg_tsp_1p8v: regulator-tsp-1p8v {
>  		compatible = "regulator-fixed";
>  		regulator-name = "tsp_1p8v";
> @@ -418,6 +467,18 @@ accel_int_default_state: accel-int-default-state {
>  		bias-disable;
>  	};
>  
> +	backlight_i2c_default_state: backlight-i2c-default-state {
> +		pins = "gpio20", "gpio21";
> +		function = "gpio";
> +		drive-strength = <2>;
> +		bias-disable;
> +	};
> +
> +	backlight_pwm_default_state: backlight-pwm-default-state {
> +		pins = "gpio33";
> +		function = "gp0_clk";
> +	};
> +
>  	muic_int_default_state: muic-int-default-state {
>  		pins = "gpio67";
>  		function = "gpio";