Re: [PATCH 3/4] arm64: dts: qcom: sm6350: Add CCI nodes

[Konrad Dybcio]

On 20.01.2023 12:11, Luca Weiss wrote:
> Add nodes for the two CCI blocks found on SM6350.
> 
> The first contains two i2c busses and while the second one might also
> contains two busses, the downstream kernel only has one configured, and
> some boards use the GPIOs for the potential cci1_i2c1 one other
> purposes, so leave that one unconfigured.
> 
> Signed-off-by: Luca Weiss <luca.weiss@xxxxxxxxxxxxx>
> ---
>  arch/arm64/boot/dts/qcom/sm6350.dtsi | 132 +++++++++++++++++++++++++++++++++++
>  1 file changed, 132 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sm6350.dtsi b/arch/arm64/boot/dts/qcom/sm6350.dtsi
> index 300ced5cda57..666c1c80e4e6 100644
> --- a/arch/arm64/boot/dts/qcom/sm6350.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sm6350.dtsi
> @@ -6,6 +6,7 @@
>  
>  #include <dt-bindings/clock/qcom,gcc-sm6350.h>
>  #include <dt-bindings/clock/qcom,rpmh.h>
> +#include <dt-bindings/clock/qcom,sm6350-camcc.h>
>  #include <dt-bindings/dma/qcom-gpi.h>
>  #include <dt-bindings/gpio/gpio.h>
>  #include <dt-bindings/interconnect/qcom,icc.h>
> @@ -1435,6 +1436,95 @@ usb_1_dwc3: usb@a600000 {
>  			};
>  		};
>  
> +		cci0: cci@ac4a000 {
> +			compatible = "qcom,sm6350-cci", "qcom,msm8996-cci";
> +			#address-cells = <1>;
> +			#size-cells = <0>;
These two belong at the bottom
> +
> +			reg = <0 0x0ac4a000 0 0x1000>;
> +			interrupts = <GIC_SPI 468 IRQ_TYPE_EDGE_RISING>;
> +			power-domains = <&camcc TITAN_TOP_GDSC>;
> +
> +			clocks = <&camcc CAMCC_CAMNOC_AXI_CLK>,
> +				 <&camcc CAMCC_SOC_AHB_CLK>,
> +				 <&camcc CAMCC_SLOW_AHB_CLK_SRC>,
> +				 <&camcc CAMCC_CPAS_AHB_CLK>,
> +				 <&camcc CAMCC_CCI_0_CLK>,
> +				 <&camcc CAMCC_CCI_0_CLK_SRC>;
> +			clock-names = "camnoc_axi",
> +				      "soc_ahb",
> +				      "slow_ahb_src",
> +				      "cpas_ahb",
> +				      "cci",
> +				      "cci_src";
> +
> +			assigned-clocks = <&camcc CAMCC_CAMNOC_AXI_CLK>,
> +					  <&camcc CAMCC_CCI_0_CLK>;
> +			assigned-clock-rates = <80000000>, <37500000>;
> +
> +			pinctrl-names = "default", "sleep";
Please move pinctrl-names below pinctrl-N for consistency
with other properties ending with -names.

> +			pinctrl-0 = <&cci0_default &cci1_default>;
> +			pinctrl-1 = <&cci0_sleep &cci1_sleep>;
> +
> +			status = "disabled";
> +
> +			cci0_i2c0: i2c-bus@0 {
> +				reg = <0>;
> +				clock-frequency = <1000000>;
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +			};
> +
> +			cci0_i2c1: i2c-bus@1 {
> +				reg = <1>;
> +				clock-frequency = <1000000>;
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +			};
> +		};
> +
> +		cci1: cci@ac4b000 {
> +			compatible = "qcom,sm6350-cci", "qcom,msm8996-cci";
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			reg = <0 0x0ac4b000 0 0x1000>;
> +			interrupts = <GIC_SPI 462 IRQ_TYPE_EDGE_RISING>;
> +			power-domains = <&camcc TITAN_TOP_GDSC>;
> +
> +			clocks = <&camcc CAMCC_CAMNOC_AXI_CLK>,
> +				 <&camcc CAMCC_SOC_AHB_CLK>,
> +				 <&camcc CAMCC_SLOW_AHB_CLK_SRC>,
> +				 <&camcc CAMCC_CPAS_AHB_CLK>,
> +				 <&camcc CAMCC_CCI_1_CLK>,
> +				 <&camcc CAMCC_CCI_1_CLK_SRC>;
> +			clock-names = "camnoc_axi",
> +				      "soc_ahb",
> +				      "slow_ahb_src",
> +				      "cpas_ahb",
> +				      "cci",
> +				      "cci_src";
> +
> +			assigned-clocks = <&camcc CAMCC_CAMNOC_AXI_CLK>,
> +					  <&camcc CAMCC_CCI_1_CLK>;
> +			assigned-clock-rates = <80000000>, <37500000>;
> +
> +			pinctrl-names = "default", "sleep";
> +			pinctrl-0 = <&cci2_default>;
> +			pinctrl-1 = <&cci2_sleep>;
> +
> +			status = "disabled";
> +
> +			cci1_i2c0: i2c-bus@0 {
> +				reg = <0>;
> +				clock-frequency = <1000000>;
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +			};
> +
> +			/* SM6350 seems to have cci1_i2c1 on gpio2 & gpio3 but unused downstream */
> +		};
> +
>  		camcc: clock-controller@ad00000 {
>  			compatible = "qcom,sm6350-camcc";
>  			reg = <0 0x0ad00000 0 0x16000>;
> @@ -1522,6 +1612,48 @@ tlmm: pinctrl@f100000 {
>  			#interrupt-cells = <2>;
>  			gpio-ranges = <&tlmm 0 0 157>;
>  
> +			cci0_default: cci0-default-state {
> +				pins = "gpio39", "gpio40";
> +				function = "cci_i2c";
> +				bias-pull-up;
Most other pin definitions in our directory have bias
properties below drive-strength, please reorder.

Konrad
> +				drive-strength = <2>;
> +			};
> +
> +			cci0_sleep: cci0-sleep-state {
> +				pins = "gpio39", "gpio40";
> +				function = "cci_i2c";
> +				bias-pull-down;
> +				drive-strength = <2>;
> +			};
> +
> +			cci1_default: cci1-default-state {
> +				pins = "gpio41", "gpio42";
> +				function = "cci_i2c";
> +				bias-pull-up;
> +				drive-strength = <2>;
> +			};
> +
> +			cci1_sleep: cci1-sleep-state {
> +				pins = "gpio41", "gpio42";
> +				function = "cci_i2c";
> +				bias-pull-down;
> +				drive-strength = <2>;
> +			};
> +
> +			cci2_default: cci2-default-state {
> +				pins = "gpio43", "gpio44";
> +				function = "cci_i2c";
> +				bias-pull-up;
> +				drive-strength = <2>;
> +			};
> +
> +			cci2_sleep: cci2-sleep-state {
> +				pins = "gpio43", "gpio44";
> +				function = "cci_i2c";
> +				bias-pull-down;
> +				drive-strength = <2>;
> +			};
> +
>  			sdc2_off_state: sdc2-off-state {
>  				clk-pins {
>  					pins = "sdc2_clk";
>