Re: [RFC v4 2/5] usb: dwc3: core: Refactor PHY logic to support Multiport Controller
From: Shazad Hussain
Date: Tue Jan 24 2023 - 03:22:33 EST
On 1/20/2023 8:48 PM, Krishna Kurapati PSSNV wrote:
On 1/20/2023 8:43 PM, Krishna Kurapati PSSNV wrote:
On 1/20/2023 8:07 PM, Andrew Halaney wrote:
On Fri, Jan 20, 2023 at 07:25:57AM +0530, Krishna Kurapati PSSNV wrote:
On 1/20/2023 3:39 AM, Andrew Halaney wrote:
On Sun, Jan 15, 2023 at 05:11:43PM +0530, Krishna Kurapati wrote:
Currently the DWC3 driver supports only single port controller
which requires at most one HS and one SS PHY.
But the DWC3 USB controller can be connected to multiple ports and
each port can have their own PHYs. Each port of the multiport
controller can either be HS+SS capable or HS only capable
Proper quantification of them is required to modify GUSB2PHYCFG
and GUSB3PIPECTL registers appropriately.
Add support for detecting, obtaining and configuring phy's supported
by a multiport controller and limit the max number of ports
supported to 4.
Signed-off-by: Harsh Agarwal <quic_harshq@xxxxxxxxxxx>
Signed-off-by: Krishna Kurapati <quic_kriskura@xxxxxxxxxxx>
---
drivers/usb/dwc3/core.c | 304
+++++++++++++++++++++++++++++-----------
drivers/usb/dwc3/core.h | 15 +-
drivers/usb/dwc3/drd.c | 14 +-
3 files changed, 244 insertions(+), 89 deletions(-)
diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c
index 476b63618511..7e0a9a598dfd 100644
--- a/drivers/usb/dwc3/core.c
+++ b/drivers/usb/dwc3/core.c
<snip>
@@ -1575,6 +1690,21 @@ static void dwc3_get_properties(struct dwc3
*dwc)
dwc->dis_split_quirk = device_property_read_bool(dev,
"snps,dis-split-quirk");
+
+ /*
+ * If no mulitport properties are defined, default
+ * the port count to '1'.
+ */
+ ret = device_property_read_u32(dev, "num-ports",
+ &dwc->num_ports);
+ if (ret)
+ dwc->num_ports = 1;
+
+ ret = device_property_read_u32(dev, "num-ss-ports",
+ &dwc->num_ss_ports);
+ if (ret)
+ dwc->num_ss_ports = 1;
By using this DT property instead of using the number of each phy
type you
find you can get into situations where you're writing
DWC3_GUSB2PHYCFG, etc,
when there's no phy to go along with it.
Hi Andrew,
Thanks for the review. Yes, this decoupling is still there and its
fine I
believe.
I ran into this when testing on sa8540p-ride, which only uses one
of the
ports on the multiport controller. I didn't enable the other phys (not
sure if that was smart or not) and overrode phy-names/phys, but did
not
override num-ports/num-ss-ports, which resulted in that. Nothing bad
happened on a quick test.. but I thought I'd highlight that as another
downside of decoupling this value from the number of phys you grab.
If we do not override phy-names or num-ports/num-ss-ports info in
DT, they
are just defaulted to '1' and as per the current logic only port-1
registers
must be configured. Isn't that the case happening ?
In my dts I'm inheriting from the sc8280xp.dtsi usb_2 phandle you've
created!
So unless I override them I get this from your sc8280xp.dtsi:
+ usb_2_dwc3: usb@a400000 {
+ compatible = "snps,dwc3";
+ reg = <0 0x0a400000 0 0xcd00>;
+ interrupts = <GIC_SPI 133
IRQ_TYPE_LEVEL_HIGH>;
+ iommus = <&apps_smmu 0x800 0x0>;
+ num-ports = <4>;
+ num-ss-ports = <2>;
+ phys = <&usb_2_hsphy0>,
<&usb_2_qmpphy0>,
+ <&usb_2_hsphy1>,
<&usb_2_qmpphy1>,
+ <&usb_2_hsphy2>,
+ <&usb_2_hsphy3>;
+ phy-names = "usb2-phy_port0",
"usb3-phy_port0",
+ "usb2-phy_port1",
"usb3-phy_port1",
+ "usb2-phy_port2",
+ "usb2-phy_port3";
+ };
Since this board only uses one port of the multiport controller, I
redefined phys/phy-names to indicate that. I figured that was more
desireable than enabling unnecessary phys. Without overriding
num-ports/num-ss-ports all the for loops in this patch would act like
the values were 4 and 2 respectively, writing to DWC3_GUSB2PHYCFG
multiple times etc as well as look for the multiport phy-names and fail
to actually get any phys. Hope that makes sense!
Hi Andrew,
My Bad. I missed the fact that it was based on sc8280xp.dtsi. In
that case it makes complete sense to override the num-ports and
num-ss-ports to "1" and the usb phy-names.
Here's a patch enabling sa8540p-ride, I'd love if you'd add it to the
series (probably needs clean up after review, and will definitely need
alteration after you update the dt-binding again). If not I'll
continue
to test/review so please CC me!:
Sure, I can add this patch (probably will add the other phy's too)
during
the final submission.
I don't have a great understanding of the mapping of the phys to
physical connections (as well as what registers like DWC3_GUSB2PHYCFG
do),
so if it makes more sense to enable all the relevant SoC phys, write
those registers in the DWC3 IP, etc, and only use one of the actual
board outputs then feel free. I think this is a good example of "what if
a board designer only uses a single port of the multiport IP" imo.
Agreed. This could be a good example of multi port with only single port
Typo in the previous mail. Correcting it here.
working.
Agreed, The dt-patch you provided will be a good working example of
getting just a single port working for a multiport controller.
Regards,
Krishna,
From dcb27d07f079194ebd7efe1c9bec64da78beb290 Mon Sep 17 00:00:00
2001
From: Andrew Halaney <ahalaney@xxxxxxxxxx>
Date: Thu, 19 Jan 2023 14:53:38 -0600
Subject: [PATCH] arm64: dts: qcom: sa8540p-ride: Enable usb_2
Content-type: text/plain
There is now support for the multiport USB controller this uses
so enable it.
The board only has a single port hooked up (despite it being wired
up to
the multiport IP on the SoC). There's also a USB 2.0 mux hooked up,
which by default on boot is selected to mux properly. Grab the gpio
controlling that and ensure it stays in the right position so USB 2.0
continues to be routed from the external port to the SoC.
Signed-off-by: Andrew Halaney <ahalaney@xxxxxxxxxx>
---
arch/arm64/boot/dts/qcom/sa8540p-ride.dts | 24
+++++++++++++++++++++++
1 file changed, 24 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
b/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
index 97957f3baa64..56d4f43faa1e 100644
--- a/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
+++ b/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
@@ -246,6 +246,21 @@ &usb_0_qmpphy {
status = "okay";
};
+&usb_2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb2_en_state>;
+
+ status = "okay";
+};
+
+&usb_2_dwc3 {
+ dr_mode = "host";
+ num-ports = <1>;
+ num-ss-ports = <1>;
More over, if this is a multiport controller and you are using only
port-1,
it is as good as a single port controller I believe and the normal DT
convention must work. Adding these properties as "1" is not required
as the
driver logic defaults them to "1" if they are not found.
See above comment about inheriting from sc8280xp.dtsi and needing to
override their values.
Just to add a point here (as I was not clear in DT Binding
description, My
bad), the num-ports and num-ss-ports must indicate the HS/SS Phys
present on
HW whether they are used in DT or not. Just to cover all cases which
user
can use [1].
[]1:
https://lore.kernel.org/all/4eb26a54-148b-942f-01c6-64e66541de8b@xxxxxxxxxxx/
Ok, if you're going with that approach of "must indicate the HS/SS Phys
present on HW whether they are used in the DT or not" (/me assumes DT
here means on the board and not an incorrect coding of the DT) then I
suppose I should not have overridden anything but phys/phy-names to
indicate that I'm only using the first port (and used the multiport
phy-names convention). It looks like in that link you also mention that
it is ok to write to DWC3_GUSB2PHYCFG and friends even if the phy isn't
defined, which was my concern and reasoning above for overriding
num-ports/num-ss-ports.
Thanks,
Andrew
Actually, I was trying to mandate that rule to take care of cases
where the phy's for say port2 or port3 are missing for a quad port
controller in dtsi and we don't want to end up configuring wrong
dwc3-phy regs.
For just the first port, the changes you have mentioned must be
sufficient. (Furthermore, thanks for the review and testing it on
sa8295-ride and confirming nothing breaks while the first port is
enabled)
I agree that for ride platform the changes provided with overridden
phys in DT for the sa8540-ride.dts makes more sense with only having
port0 of multi port on this platform.
Looking forward to validate the next version on ride platform.
Krishna, please keep me in cc in the next version :).
-Shazad
Regards,
Krishna,
Regards,
Krishna,
+ phy-names = "usb2-phy", "usb3-phy";
+ phys = <&usb_2_hsphy0>, <&usb_2_qmpphy0>;
+};
+
&usb_2_hsphy0 {
vdda-pll-supply = <&vreg_l5a>;
vdda18-supply = <&vreg_l7g>;
@@ -313,4 +328,13 @@ wake-pins {
bias-pull-up;
};
};
+
+ usb2_en_state: usb2-en-state {
+ /* TS3USB221A USB2.0 mux select */
+ pins = "gpio24";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ output-low;
+ };
};