[PATCH 6/8] ASoC: codecs: lpass: fix incorrect mclk rate

[Srinivas Kandagatla]

For some reason we ended up with incorrect mclk rate which should be
1920000 instead of 96000, So far we were getting lucky as the same clk
is set to 192000 by wsa and va macro. This issue is discovered when there
is no wsa macro active and only rx or tx path is tested.
Fix this by setting correct rate.

Fixes: c39667ddcfc5 ("ASoC: codecs: lpass-tx-macro: add support for lpass tx macro")
Fixes: af3d54b99764 ("ASoC: codecs: lpass-rx-macro: add support for lpass rx macro")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@xxxxxxxxxx>
---
 sound/soc/codecs/lpass-rx-macro.c | 4 ++--
 sound/soc/codecs/lpass-tx-macro.c | 4 ++--
 2 files changed, 4 insertions(+), 4 deletions(-)

diff --git a/sound/soc/codecs/lpass-rx-macro.c b/sound/soc/codecs/lpass-rx-macro.c
index dd6970d5eb8d..8621cfabcf5b 100644
--- a/sound/soc/codecs/lpass-rx-macro.c
+++ b/sound/soc/codecs/lpass-rx-macro.c
@@ -366,7 +366,7 @@
 #define CDC_RX_DSD1_CFG2			(0x0F8C)
 #define RX_MAX_OFFSET				(0x0F8C)
 
-#define MCLK_FREQ		9600000
+#define MCLK_FREQ		19200000
 
 #define RX_MACRO_RATES (SNDRV_PCM_RATE_8000 | SNDRV_PCM_RATE_16000 |\
 			SNDRV_PCM_RATE_32000 | SNDRV_PCM_RATE_48000 |\
@@ -3579,7 +3579,7 @@ static int rx_macro_probe(struct platform_device *pdev)
 
 	/* set MCLK and NPL rates */
 	clk_set_rate(rx->mclk, MCLK_FREQ);
-	clk_set_rate(rx->npl, 2 * MCLK_FREQ);
+	clk_set_rate(rx->npl, MCLK_FREQ);
 
 	ret = clk_prepare_enable(rx->macro);
 	if (ret)
diff --git a/sound/soc/codecs/lpass-tx-macro.c b/sound/soc/codecs/lpass-tx-macro.c
index b9475ba55e20..2449a2df66df 100644
--- a/sound/soc/codecs/lpass-tx-macro.c
+++ b/sound/soc/codecs/lpass-tx-macro.c
@@ -203,7 +203,7 @@
 #define TX_MACRO_AMIC_UNMUTE_DELAY_MS	100
 #define TX_MACRO_DMIC_HPF_DELAY_MS	300
 #define TX_MACRO_AMIC_HPF_DELAY_MS	300
-#define MCLK_FREQ		9600000
+#define MCLK_FREQ		19200000
 
 enum {
 	TX_MACRO_AIF_INVALID = 0,
@@ -2014,7 +2014,7 @@ static int tx_macro_probe(struct platform_device *pdev)
 
 	/* set MCLK and NPL rates */
 	clk_set_rate(tx->mclk, MCLK_FREQ);
-	clk_set_rate(tx->npl, 2 * MCLK_FREQ);
+	clk_set_rate(tx->npl, MCLK_FREQ);
 
 	ret = clk_prepare_enable(tx->macro);
 	if (ret)
-- 
2.21.0