Re: thermal/drivers/tegra: Getting rid of the get_thermal_instance() usage
From: Thierry Reding
Date: Fri Feb 10 2023 - 10:12:44 EST
On Fri, Feb 10, 2023 at 03:36:59PM +0100, Daniel Lezcano wrote:
> On 10/02/2023 15:09, Thierry Reding wrote:
> > On Fri, Feb 10, 2023 at 02:17:03PM +0100, Daniel Lezcano wrote:
> > > Hi Thierry,
> > >
> > > On Thu, Jan 26, 2023 at 01:55:52PM +0100, Thierry Reding wrote:
> > > > On Tue, Jan 24, 2023 at 08:57:23PM +0100, Daniel Lezcano wrote:
> > > > >
> > > > > Hi,
> > > > >
> > > > > does anyone know what is the purpose of the get_thermal_instance() usage in
> > > > > this code:
> > > > >
> > > > > https://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux.git/tree/drivers/thermal/tegra/soctherm.c?h=thermal/linux-next#n623
> > > > >
> > > > > The driver is using a function which is reserved for the thermal core. It
> > > > > should not.
> > > > >
> > > > > Is the following change ok ?
> > > > >
> > > > > diff --git a/drivers/thermal/tegra/soctherm.c
> > > > > b/drivers/thermal/tegra/soctherm.c
> > > > > index 220873298d77..5f552402d987 100644
> > > > > --- a/drivers/thermal/tegra/soctherm.c
> > > > > +++ b/drivers/thermal/tegra/soctherm.c
> > > > > @@ -620,9 +620,8 @@ static int tegra_thermctl_set_trip_temp(struct
> > > > > thermal_zone_device *tz, int trip
> > > > > continue;
> > > > >
> > > > > cdev = ts->throt_cfgs[i].cdev;
> > > > > - if (get_thermal_instance(tz, cdev, trip_id))
> > > > > - stc = find_throttle_cfg_by_name(ts, cdev->type);
> > > > > - else
> > > > > + stc = find_throttle_cfg_by_name(ts, cdev->type);
> > > > > + if (!stc)
> > > > > continue;
> > > > >
> > > > > return throttrip_program(dev, sg, stc, temp);
> > > > > @@ -768,9 +767,9 @@ static int tegra_soctherm_set_hwtrips(struct device
> > > > > *dev,
> > > > > continue;
> > > > >
> > > > > cdev = ts->throt_cfgs[i].cdev;
> > > > > - if (get_thermal_instance(tz, cdev, trip))
> > > > > - stc = find_throttle_cfg_by_name(ts, cdev->type);
> > > > > - else
> > > > > +
> > > > > + stc = find_throttle_cfg_by_name(ts, cdev->type);
> > > > > + if (!stc)
> > > > > continue;
> > > > >
> > > > > ret = throttrip_program(dev, sg, stc, temperature);
> > > >
> > > > There's a small difference in behavior after applying this patch. Prior
> > > > to this I get (on Tegra210):
> > > >
> > > > [ 12.354091] tegra_soctherm 700e2000.thermal-sensor: missing thermtrips, will use critical trips as shut down temp
> > > > [ 12.379009] tegra_soctherm 700e2000.thermal-sensor: thermtrip: will shut down when cpu reaches 102500 mC
> > > > [ 12.388882] tegra_soctherm 700e2000.thermal-sensor: programming throttle for cpu to 102500
> > > > [ 12.401007] tegra_soctherm 700e2000.thermal-sensor: throttrip: will throttle when cpu reaches 102500 mC
> > > > [ 12.471041] tegra_soctherm 700e2000.thermal-sensor: thermtrip: will shut down when gpu reaches 103000 mC
> > > > [ 12.482852] tegra_soctherm 700e2000.thermal-sensor: programming throttle for gpu to 103000
> > > > [ 12.482860] tegra_soctherm 700e2000.thermal-sensor: throttrip: will throttle when gpu reaches 103000 mC
> > > > [ 12.485357] tegra_soctherm 700e2000.thermal-sensor: thermtrip: will shut down when pll reaches 103000 mC
> > > > [ 12.501774] tegra_soctherm 700e2000.thermal-sensor: thermtrip: will shut down when mem reaches 103000 mC
> > > >
> > > > and after these changes, it turns into:
> > > >
> > > > [ 12.447113] tegra_soctherm 700e2000.thermal-sensor: missing thermtrips, will use critical trips as shut down temp
> > > > [ 12.472300] tegra_soctherm 700e2000.thermal-sensor: thermtrip: will shut down when cpu reaches 102500 mC
> > > > [ 12.481789] tegra_soctherm 700e2000.thermal-sensor: programming throttle for cpu to 102500
> > > > [ 12.495447] tegra_soctherm 700e2000.thermal-sensor: throttrip: will throttle when cpu reaches 102500 mC
> > > > [ 12.496514] tegra_soctherm 700e2000.thermal-sensor: thermtrip: will shut down when gpu reaches 103000 mC
> > > > [ 12.510353] tegra_soctherm 700e2000.thermal-sensor: programming throttle for gpu to 103000
> > > > [ 12.526856] tegra_soctherm 700e2000.thermal-sensor: throttrip: will throttle when gpu reaches 103000 mC
> > > > [ 12.528774] tegra_soctherm 700e2000.thermal-sensor: thermtrip: will shut down when pll reaches 103000 mC
> > > > [ 12.569352] tegra_soctherm 700e2000.thermal-sensor: programming throttle for pll to 103000
> > > > [ 12.577635] tegra_soctherm 700e2000.thermal-sensor: throttrip: will throttle when pll reaches 103000 mC
> > > > [ 12.590952] tegra_soctherm 700e2000.thermal-sensor: thermtrip: will shut down when mem reaches 103000 mC
> > > > [ 12.600783] tegra_soctherm 700e2000.thermal-sensor: programming throttle for mem to 103000
> > > > [ 12.609204] tegra_soctherm 700e2000.thermal-sensor: throttrip: will throttle when mem reaches 103000 mC
> > > >
> > > > The "programming throttle ..." messages are something I've added locally
> > > > to trace what gets called. So it looks like for "pll" and "mem" thermal
> > > > zones, we now program trip points whereas we previously didn't.
> > >
> > > The DT descriptioni (tegra210.dtsi) says one thing and the implementation says
> > > something else.
> > >
> > > If we refer to the PLL description, there is one 'hot' trip point and
> > > one 'critical' trip point. No polling delay at all, so we need the
> > > interrupts.
> > >
> > > Logically, we should set the 'hot' trip point first, when the trip
> > > point is crossed, we setup the next trip point, which is the critical.
> > >
> > > With these two trip points, the first one will send a notification to
> > > the userspace and the second one will force a shutdown of the
> > > system. For both, no cooling device is expected.
> >
> > I think the intention here is to use the soctherm's built-in throttling
> > mechanism as a last resort measure to try and cool the system down. I
> > suppose that could count as "passive" cooling, so specifying it as the
> > cooling device for the "passive" trip point may be more appropriate.
> >
> > The throttling that happens here is quite severe, so we don't want it to
> > happen too early. I would expect that our "passive" trip point shouldn't
> > be a lot less than the "hot" temperature. I suspect that's the reason
> > why the "hot" trip point was reused for this.
> >
> > I'm also beginning to think that we should just not expose the soctherm
> > throttling as a cooling device and instead keep it internal to the
> > soctherm driver entirely.
>
> Yes, and perhaps separate it from the sensor driver.
>
> There is a similar hardware limiter for the qcom platform [1]. The
> description in the device tree is separated from the sensor and the binding
> has temperatures to begin the mitigation [2].
The hardware throttling is controlled using registers that are part of
the SOCTHERM block, so we can't separate it from the sensor driver. I
don't think that's much of a problem, though. The code for this already
exists in the current soctherm driver, so it's just a matter of removing
the cooling device registration code.
>
> There is no trip point associated as those are related to the in-kernel
> mitigation.
>
> If this mitigation is a heavy mitigation, above what the kernel is able to
> do with a passive cooling device. It would make sense to just have
> configured outside of the thermal zone.
>
> So the configuration would be something like:
>
> myperformance_limite {
> @ = <0x...>
> temperature_limit = 95000;
> };
>
> thermal_zone {
>
> cpu : {
> trips {
> alert {
> temperature = 90000;
> hysteresis = 2000;
> type = passive;
> };
>
> hot {
> temperature = 97000;
> type = hot;
> };
>
> critical {
> temperature = 100000;
> hysteresis = 2000;
> type = critical;
> };
>
> cooling-maps = <&cpu NO_LIMIT NO_LIMIT>;
> };
> }
> };
>
> The behavior will be a passive mitigation, if it fails the hardware limiter
> will take over, if that fails then hot sends a notification to the userspace
> (giving the opportunity to hotplug a cpu or kill a task or suspend), if that
> fails then shutdown.
Yeah, that's exactly what I had in mind.
> [1] https://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux.git/tree/drivers/thermal/qcom/lmh.c?h=thermal/bleeding-edge
>
> [2] https://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux.git/tree/arch/arm64/boot/dts/qcom/sdm845.dtsi?h=thermal/bleeding-edge#n3922
>
> [ ... ]
>
> > On the DT side, I think most of the cooling maps can be cleaned up. We
> > can remove the entries for "critical" and "hot" trip points if the
> > driver unconditionally programs the automated throttling.
>
> You may want to keep the critical trip points at least. Even if the hardware
> limiter is certainly very effective, having the critical point is another
> fail safe allowing to gracefully shutdown the system before a wild hardware
> reset.
Yeah. What I meant was to remove only the cooling map entries for
critical and hot since they would be unused. We absolutely want to
keep the trip points themselves around to make sure the system will
forcefully shutdown as a last resort.
Thierry
Attachment:
signature.asc
Description: PGP signature