[PATCH 7/7] arm64: dts: qcom: ipq9574: Add PCIe PHYs and controller nodes

From: Devi Priya
Date: Tue Feb 14 2023 - 11:44:21 EST

Next message: Randy Dunlap: "Re: [PATCH] fixed typos on selftests/bpf"
Previous message: Devi Priya: "[PATCH 6/7] clk: qcom: gcc-ipq9574: Add PCIe related clocks"
In reply to: Devi Priya: "[PATCH 6/7] clk: qcom: gcc-ipq9574: Add PCIe related clocks"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

Add PCIe0, PCIe1, PCIe2, PCIe3 (and corresponding PHY) devices
found on IPQ9574 platform. The PCIe0 & PCIe1 are 1-lane Gen3
host whereas PCIe2 & PCIe3 are 2-lane Gen3 host.

Co-developed-by: Anusha Rao <quic_anusha@xxxxxxxxxxx>
Signed-off-by: Anusha Rao <quic_anusha@xxxxxxxxxxx>
Signed-off-by: Devi Priya <quic_devipriy@xxxxxxxxxxx>
---
arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts | 28 ++
arch/arm64/boot/dts/qcom/ipq9574.dtsi | 477 ++++++++++++++++++-
2 files changed, 499 insertions(+), 6 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts b/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts
index 2c8430197ec0..21b53f34ce84 100644
--- a/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts
+++ b/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts
@@ -8,6 +8,7 @@

/dts-v1/;

+#include <dt-bindings/gpio/gpio.h>
#include "ipq9574.dtsi"

/ {
@@ -29,6 +30,33 @@
status = "okay";
};

+&pcie1_phy {
+ status = "okay";
+};
+
+&pcie1_x1 {
+ perst-gpios = <&tlmm 26 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&pcie2_phy {
+ status = "okay";
+};
+
+&pcie2_x2 {
+ perst-gpios = <&tlmm 29 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&pcie3_phy {
+ status = "okay";
+};
+
+&pcie3_x2 {
+ perst-gpios = <&tlmm 32 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
&sdhc_1 {
pinctrl-0 = <&sdc_default_state>;
pinctrl-names = "default";
diff --git a/arch/arm64/boot/dts/qcom/ipq9574.dtsi b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
index 062f80798ebb..a32dbdeb5bed 100644
--- a/arch/arm64/boot/dts/qcom/ipq9574.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
@@ -6,8 +6,8 @@
* Copyright (c) 2023, Qualcomm Innovation Center, Inc. All rights reserved.
*/

-#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/clock/qcom,ipq9574-gcc.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/reset/qcom,ipq9574-gcc.h>

/ {
@@ -22,11 +22,41 @@
#clock-cells = <0>;
};

+ pcie30_phy0_pipe_clk: pcie30_phy0_pipe_clk {
+ compatible = "fixed-clock";
+ clock-frequency = <250000000>;
+ #clock-cells = <0>;
+ };
+
+ pcie30_phy1_pipe_clk: pcie30_phy1_pipe_clk {
+ compatible = "fixed-clock";
+ clock-frequency = <250000000>;
+ #clock-cells = <0>;
+ };
+
+ pcie30_phy2_pipe_clk: pcie30_phy2_pipe_clk {
+ compatible = "fixed-clock";
+ clock-frequency = <250000000>;
+ #clock-cells = <0>;
+ };
+
+ pcie30_phy3_pipe_clk: pcie30_phy3_pipe_clk {
+ compatible = "fixed-clock";
+ clock-frequency = <250000000>;
+ #clock-cells = <0>;
+ };
+
sleep_clk: sleep-clk {
compatible = "fixed-clock";
#clock-cells = <0>;
};

+ usb3phy_0_cc_pipe_clk: usb3phy_0_cc_pipe_clk {
+ compatible = "fixed-clock";
+ clock-frequency = <125000000>;
+ #clock-cells = <0>;
+ };
+
xo_board_clk: xo-board-clk {
compatible = "fixed-clock";
#clock-cells = <0>;
@@ -121,6 +151,155 @@
#size-cells = <1>;
ranges = <0 0 0 0xffffffff>;

+ pcie0_phy: phy@84000 {
+ compatible = "qcom,ipq9574-qmp-gen3x1-pcie-phy";
+ reg = <0x00084000 0x1bc>; /* Serdes PLL */
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ clocks = <&gcc GCC_PCIE0_AUX_CLK>,
+ <&gcc GCC_PCIE0_AHB_CLK>,
+ <&gcc GCC_ANOC_PCIE0_1LANE_M_CLK>,
+ <&gcc GCC_SNOC_PCIE0_1LANE_S_CLK>;
+ clock-names = "aux", "cfg_ahb", "anoc_lane", "snoc_lane";
+
+ assigned-clocks = <&gcc GCC_PCIE0_AUX_CLK>;
+ assigned-clock-rates = <20000000>;
+
+ resets = <&gcc GCC_PCIE0_PHY_BCR>,
+ <&gcc GCC_PCIE0PHY_PHY_BCR>;
+ reset-names = "phy", "common";
+
+ status = "disabled";
+
+ pcie0_lane: phy@84200 {
+ reg = <0x00084200 0x16c>, /* Serdes Tx */
+ <0x00084400 0x200>, /* Serdes Rx */
+ <0x00084800 0x1f0>, /* PCS: Lane0, COM, PCIE */
+ <0x00084c00 0xf4>; /* pcs_misc */
+ #phy-cells = <0>;
+
+ clocks = <&gcc GCC_PCIE0_PIPE_CLK>;
+ clock-names = "pipe0";
+ clock-output-names = "gcc_pcie0_pipe_clk_src";
+ #clock-cells = <0>;
+ };
+ };
+
+ pcie2_phy: phy@8c000 {
+ compatible = "qcom,ipq9574-qmp-gen3x2-pcie-phy";
+ reg = <0x0008c000 0x1bc>; /* Serdes PLL */
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ clocks = <&gcc GCC_PCIE2_AUX_CLK>,
+ <&gcc GCC_PCIE2_AHB_CLK>,
+ <&gcc GCC_ANOC_PCIE2_2LANE_M_CLK>,
+ <&gcc GCC_SNOC_PCIE2_2LANE_S_CLK>;
+ clock-names = "aux", "cfg_ahb", "anoc_lane", "snoc_lane";
+
+ assigned-clocks = <&gcc GCC_PCIE2_AUX_CLK>;
+ assigned-clock-rates = <20000000>;
+
+ resets = <&gcc GCC_PCIE2_PHY_BCR>,
+ <&gcc GCC_PCIE2PHY_PHY_BCR>;
+ reset-names = "phy", "common";
+
+ status = "disabled";
+
+ pcie2_lanes: phy@8c200 {
+ reg = <0x0008c200 0x16c>, /* Serdes Tx0 */
+ <0x0008c400 0x200>, /* Serdes Rx0 */
+ <0x0008d000 0x1f0>, /* PCS: Lane0, COM, PCIE */
+ <0x0008c600 0x16c>, /* Serdes Tx1 */
+ <0x0008c800 0x200>, /* Serdes Rx1 */
+ <0x0008d400 0x0f8>; /* pcs_misc */
+
+ #phy-cells = <0>;
+
+ clocks = <&gcc GCC_PCIE2_PIPE_CLK>;
+ clock-names = "pipe0";
+ clock-output-names = "gcc_pcie2_pipe_clk_src";
+ #clock-cells = <0>;
+ };
+ };
+
+ pcie3_phy: phy@f4000 {
+ compatible = "qcom,ipq9574-qmp-gen3x2-pcie-phy";
+ reg = <0x000f4000 0x1bc>; /* Serdes PLL */
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ clocks = <&gcc GCC_PCIE3_AUX_CLK>,
+ <&gcc GCC_PCIE3_AHB_CLK>,
+ <&gcc GCC_ANOC_PCIE3_2LANE_M_CLK>,
+ <&gcc GCC_SNOC_PCIE3_2LANE_S_CLK>;
+ clock-names = "aux", "cfg_ahb", "anoc_lane", "snoc_lane";
+
+ assigned-clocks = <&gcc GCC_PCIE3_AUX_CLK>;
+ assigned-clock-rates = <20000000>;
+
+ resets = <&gcc GCC_PCIE3_PHY_BCR>,
+ <&gcc GCC_PCIE3PHY_PHY_BCR>;
+ reset-names = "phy", "common";
+
+ status = "disabled";
+
+ pcie3_lanes: phy@f4200 {
+ reg = <0x000f4200 0x16c>, /* Serdes Tx0 */
+ <0x000f4400 0x200>, /* Serdes Rx0 */
+ <0x000f5000 0x1f0>, /* PCS: Lane0, COM, PCIE */
+ <0x000f4600 0x16c>, /* Serdes Tx1 */
+ <0x000f4800 0x200>, /* Serdes Rx1 */
+ <0x000f5400 0x0f8>; /* pcs_misc */
+
+ #phy-cells = <0>;
+
+ clocks = <&gcc GCC_PCIE3_PIPE_CLK>;
+ clock-names = "pipe0";
+ clock-output-names = "gcc_pcie3_pipe_clk_src";
+ #clock-cells = <0>;
+ };
+ };
+
+ pcie1_phy: phy@fc000 {
+ compatible = "qcom,ipq9574-qmp-gen3x1-pcie-phy";
+ reg = <0x000fc000 0x1bc>; /* Serdes PLL */
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ clocks = <&gcc GCC_PCIE1_AUX_CLK>,
+ <&gcc GCC_PCIE1_AHB_CLK>,
+ <&gcc GCC_ANOC_PCIE1_1LANE_M_CLK>,
+ <&gcc GCC_SNOC_PCIE1_1LANE_S_CLK>;
+ clock-names = "aux", "cfg_ahb", "anoc_lane", "snoc_lane";
+
+ assigned-clocks = <&gcc GCC_PCIE1_AUX_CLK>;
+ assigned-clock-rates = <20000000>;
+
+ resets = <&gcc GCC_PCIE1_PHY_BCR>,
+ <&gcc GCC_PCIE1PHY_PHY_BCR>;
+ reset-names = "phy", "common";
+
+ status = "disabled";
+
+ pcie1_lane: phy@fc200 {
+ reg = <0x000fc200 0x16c>, /* Serdes Tx */
+ <0x000fc400 0x200>, /* Serdes Rx */
+ <0x000fc800 0x1f0>, /* PCS: Lane0, COM, PCIE */
+ <0x000fcc00 0xf4>; /* pcs_misc */
+ #phy-cells = <0>;
+
+ clocks = <&gcc GCC_PCIE1_PIPE_CLK>;
+ clock-names = "pipe0";
+ clock-output-names = "gcc_pcie1_pipe_clk_src";
+ #clock-cells = <0>;
+ };
+ };
+
tlmm: pinctrl@1000000 {
compatible = "qcom,ipq9574-tlmm";
reg = <0x01000000 0x300000>;
@@ -145,11 +324,11 @@
clocks = <&xo_board_clk>,
<&sleep_clk>,
<&bias_pll_ubi_nc_clk>,
- <0>,
- <0>,
- <0>,
- <0>,
- <0>;
+ <&pcie30_phy0_pipe_clk>,
+ <&pcie30_phy1_pipe_clk>,
+ <&pcie30_phy2_pipe_clk>,
+ <&pcie30_phy3_pipe_clk>,
+ <&usb3phy_0_cc_pipe_clk>;
#clock-cells = <1>;
#reset-cells = <1>;
#power-domain-cells = <1>;
@@ -282,6 +461,292 @@
status = "disabled";
};
};
+
+ pcie1_x1: pci@10000000 {
+ compatible = "qcom,pcie-ipq9574";
+ reg = <0x10000000 0xf1d>,
+ <0x10000F20 0xa8>,
+ <0x10001000 0x1000>,
+ <0x000F8000 0x4000>,
+ <0x10100000 0x1000>,
+ <0x00618108 0x4>;
+ reg-names = "dbi", "elbi", "atu", "parf", "config", "aggr_noc";
+ device_type = "pci";
+ linux,pci-domain = <2>;
+ bus-range = <0x00 0xff>;
+ num-lanes = <1>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ ranges = <0x81000000 0 0x10200000 0x10200000
+ 0 0x00100000 /* downstream I/O */
+ 0x82000000 0 0x10300000 0x10300000
+ 0 0x07d00000>; /* non-prefetchable memory */
+
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0x7>;
+ interrupt-map = <0 0 0 1 &intc 0 35
+ IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+ <0 0 0 2 &intc 0 49
+ IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+ <0 0 0 3 &intc 0 84
+ IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+ <0 0 0 4 &intc 0 85
+ IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+ interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "global_irq";
+
+ /* clocks and clock-names are used to enable the clock in CBCR */
+ clocks = <&gcc GCC_PCIE1_AHB_CLK>,
+ <&gcc GCC_PCIE1_AUX_CLK>,
+ <&gcc GCC_PCIE1_AXI_M_CLK>,
+ <&gcc GCC_PCIE1_AXI_S_CLK>,
+ <&gcc GCC_PCIE1_AXI_S_BRIDGE_CLK>,
+ <&gcc GCC_PCIE1_RCHNG_CLK>;
+ clock-names = "ahb",
+ "aux",
+ "axi_m",
+ "axi_s",
+ "axi_bridge",
+ "rchng";
+
+ resets = <&gcc GCC_PCIE1_PIPE_ARES>,
+ <&gcc GCC_PCIE1_CORE_STICKY_ARES>,
+ <&gcc GCC_PCIE1_AXI_S_STICKY_ARES>,
+ <&gcc GCC_PCIE1_AXI_S_ARES>,
+ <&gcc GCC_PCIE1_AXI_M_STICKY_ARES>,
+ <&gcc GCC_PCIE1_AXI_M_ARES>,
+ <&gcc GCC_PCIE1_AUX_ARES>,
+ <&gcc GCC_PCIE1_AHB_ARES>;
+ reset-names = "pipe",
+ "sticky",
+ "axi_s_sticky",
+ "axi_s",
+ "axi_m_sticky",
+ "axi_m",
+ "aux",
+ "ahb";
+
+ phys = <&pcie1_lane>;
+ phy-names = "pciephy";
+ msi-parent = <&v2m0>;
+ status = "disabled";
+ };
+
+ pcie3_x2: pci@18000000 {
+ compatible = "qcom,pcie-ipq9574";
+ reg = <0x18000000 0xf1d>,
+ <0x18000F20 0xa8>,
+ <0x18001000 0x1000>,
+ <0x000F0000 0x4000>,
+ <0x18100000 0x1000>;
+ reg-names = "dbi", "elbi", "atu", "parf", "config";
+ device_type = "pci";
+ linux,pci-domain = <4>;
+ bus-range = <0x00 0xff>;
+ num-lanes = <2>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ ranges = <0x81000000 0 0x18200000 0x18200000
+ 0 0x00100000 /* downstream I/O */
+ 0x82000000 0 0x18300000 0x18300000
+ 0 0x07d00000>; /* non-prefetchable memory */
+
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0x7>;
+ interrupt-map = <0 0 0 1 &intc 0 189
+ IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+ <0 0 0 2 &intc 0 190
+ IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+ <0 0 0 3 &intc 0 191
+ IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+ <0 0 0 4 &intc 0 192
+ IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+ interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "global_irq";
+
+ /* clocks and clock-names are used to enable the clock in CBCR */
+ clocks = <&gcc GCC_PCIE3_AHB_CLK>,
+ <&gcc GCC_PCIE3_AUX_CLK>,
+ <&gcc GCC_PCIE3_AXI_M_CLK>,
+ <&gcc GCC_PCIE3_AXI_S_CLK>,
+ <&gcc GCC_PCIE3_AXI_S_BRIDGE_CLK>,
+ <&gcc GCC_PCIE3_RCHNG_CLK>;
+ clock-names = "ahb",
+ "aux",
+ "axi_m",
+ "axi_s",
+ "axi_bridge",
+ "rchng";
+
+ resets = <&gcc GCC_PCIE3_PIPE_ARES>,
+ <&gcc GCC_PCIE3_CORE_STICKY_ARES>,
+ <&gcc GCC_PCIE3_AXI_S_STICKY_ARES>,
+ <&gcc GCC_PCIE3_AXI_S_ARES>,
+ <&gcc GCC_PCIE3_AXI_M_STICKY_ARES>,
+ <&gcc GCC_PCIE3_AXI_M_ARES>,
+ <&gcc GCC_PCIE3_AUX_ARES>,
+ <&gcc GCC_PCIE3_AHB_ARES>;
+ reset-names = "pipe",
+ "sticky",
+ "axi_s_sticky",
+ "axi_s",
+ "axi_m_sticky",
+ "axi_m",
+ "aux",
+ "ahb";
+
+ phys = <&pcie3_lanes>;
+ phy-names = "pciephy";
+ msi-parent = <&v2m0>;
+ status = "disabled";
+ };
+
+ pcie2_x2: pci@20000000 {
+ compatible = "qcom,pcie-ipq9574";
+ reg = <0x20000000 0xf1d>,
+ <0x20000F20 0xa8>,
+ <0x20001000 0x1000>,
+ <0x00088000 0x4000>,
+ <0x20100000 0x1000>;
+ reg-names = "dbi", "elbi", "atu", "parf", "config";
+ device_type = "pci";
+ linux,pci-domain = <3>;
+ bus-range = <0x00 0xff>;
+ num-lanes =<2>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ ranges = <0x81000000 0 0x20200000 0x20200000
+ 0 0x00100000 /* downstream I/O */
+ 0x82000000 0 0x20300000 0x20300000
+ 0 0x07d00000>; /* non-prefetchable memory */
+
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0x7>;
+ interrupt-map = <0 0 0 1 &intc 0 164
+ IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+ <0 0 0 2 &intc 0 165
+ IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+ <0 0 0 3 &intc 0 186
+ IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+ <0 0 0 4 &intc 0 187
+ IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+ interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "global_irq";
+
+ /* clocks and clock-names are used to enable the clock in CBCR */
+ clocks = <&gcc GCC_PCIE2_AHB_CLK>,
+ <&gcc GCC_PCIE2_AUX_CLK>,
+ <&gcc GCC_PCIE2_AXI_M_CLK>,
+ <&gcc GCC_PCIE2_AXI_S_CLK>,
+ <&gcc GCC_PCIE2_AXI_S_BRIDGE_CLK>,
+ <&gcc GCC_PCIE2_RCHNG_CLK>;
+ clock-names = "ahb",
+ "aux",
+ "axi_m",
+ "axi_s",
+ "axi_bridge",
+ "rchng";
+
+ resets = <&gcc GCC_PCIE2_PIPE_ARES>,
+ <&gcc GCC_PCIE2_CORE_STICKY_ARES>,
+ <&gcc GCC_PCIE2_AXI_S_STICKY_ARES>,
+ <&gcc GCC_PCIE2_AXI_S_ARES>,
+ <&gcc GCC_PCIE2_AXI_M_STICKY_ARES>,
+ <&gcc GCC_PCIE2_AXI_M_ARES>,
+ <&gcc GCC_PCIE2_AUX_ARES>,
+ <&gcc GCC_PCIE2_AHB_ARES>;
+ reset-names = "pipe",
+ "sticky",
+ "axi_s_sticky",
+ "axi_s",
+ "axi_m_sticky",
+ "axi_m",
+ "aux",
+ "ahb";
+
+ phys = <&pcie2_lanes>;
+ phy-names = "pciephy";
+ msi-parent = <&v2m0>;
+ status = "disabled";
+ };
+
+ pcie0_x1: pci@28000000 {
+ compatible = "qcom,pcie-ipq9574";
+ reg = <0x28000000 0xf1d>,
+ <0x28000F20 0xa8>,
+ <0x28001000 0x1000>,
+ <0x00080000 0x2000>,
+ <0x28100000 0x1000>,
+ <0x00618088 0x4>;
+ reg-names = "dbi", "elbi", "atu", "parf", "config", "aggr_noc";
+ device_type = "pci";
+ linux,pci-domain = <1>;
+ bus-range = <0x00 0xff>;
+ num-lanes = <1>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ ranges = <0x81000000 0 0x28200000 0x28200000
+ 0 0x00100000 /* downstream I/O */
+ 0x82000000 0 0x28300000 0x28300000
+ 0 0x07d00000>; /* non-prefetchable memory */
+
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0x7>;
+ interrupt-map = <0 0 0 1 &intc 0 75
+ IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+ <0 0 0 2 &intc 0 78
+ IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+ <0 0 0 3 &intc 0 79
+ IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+ <0 0 0 4 &intc 0 83
+ IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+ interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "global_irq";
+
+ /* clocks and clock-names are used to enable the clock in CBCR */
+ clocks = <&gcc GCC_PCIE0_AHB_CLK>,
+ <&gcc GCC_PCIE0_AUX_CLK>,
+ <&gcc GCC_PCIE0_AXI_M_CLK>,
+ <&gcc GCC_PCIE0_AXI_S_CLK>,
+ <&gcc GCC_PCIE0_AXI_S_BRIDGE_CLK>,
+ <&gcc GCC_PCIE0_RCHNG_CLK>;
+ clock-names = "ahb",
+ "aux",
+ "axi_m",
+ "axi_s",
+ "axi_bridge",
+ "rchng";
+
+ resets = <&gcc GCC_PCIE0_PIPE_ARES>,
+ <&gcc GCC_PCIE0_CORE_STICKY_ARES>,
+ <&gcc GCC_PCIE0_AXI_S_STICKY_ARES>,
+ <&gcc GCC_PCIE0_AXI_S_ARES>,
+ <&gcc GCC_PCIE0_AXI_M_STICKY_ARES>,
+ <&gcc GCC_PCIE0_AXI_M_ARES>,
+ <&gcc GCC_PCIE0_AUX_ARES>,
+ <&gcc GCC_PCIE0_AHB_ARES>;
+ reset-names = "pipe",
+ "sticky",
+ "axi_s_sticky",
+ "axi_s",
+ "axi_m_sticky",
+ "axi_m",
+ "aux",
+ "ahb";
+
+ phys = <&pcie0_lane>;
+ phy-names = "pciephy";
+ msi-parent = <&v2m0>;
+ status = "disabled";
+ };
};

timer {
--
2.17.1

Next message: Randy Dunlap: "Re: [PATCH] fixed typos on selftests/bpf"
Previous message: Devi Priya: "[PATCH 6/7] clk: qcom: gcc-ipq9574: Add PCIe related clocks"
In reply to: Devi Priya: "[PATCH 6/7] clk: qcom: gcc-ipq9574: Add PCIe related clocks"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]