Re: [RFC] Support for Arm CCA VMs on Linux

From: Ryan Roberts
Date: Mon Feb 20 2023 - 05:52:08 EST


On 17/02/2023 08:02, Itaru Kitayama wrote:
> On Sat, Feb 11, 2023 at 7:53 AM Itaru Kitayama <itaru.kitayama@xxxxxxxxx> wrote:
>>
>> On Sat, Feb 11, 2023 at 1:56 AM Ryan Roberts <ryan.roberts@xxxxxxx> wrote:
>>>
>>> On 27/01/2023 11:22, Suzuki K Poulose wrote:
>>>> [...]
>>>
>>>> Running the stack
>>>> ====================
>>>>
>>>> To run/test the stack, you would need the following components :
>>>>
>>>> 1) FVP Base AEM RevC model with FEAT_RME support [4]
>>>> 2) TF-A firmware for EL3 [5]
>>>> 3) TF-A RMM for R-EL2 [3]
>>>> 4) Linux Kernel [6]
>>>> 5) kvmtool [7]
>>>> 6) kvm-unit-tests [8]
>>>>
>>>> Instructions for building the firmware components and running the model are
>>>> available here [9]. Once, the host kernel is booted, a Realm can be launched by
>>>> invoking the `lkvm` commad as follows:
>>>>
>>>> $ lkvm run --realm \
>>>> --measurement-algo=["sha256", "sha512"] \
>>>> --disable-sve \
>>>> <normal-vm-options>
>>>>
>>>> Where:
>>>> * --measurement-algo (Optional) specifies the algorithm selected for creating the
>>>> initial measurements by the RMM for this Realm (defaults to sha256).
>>>> * GICv3 is mandatory for the Realms.
>>>> * SVE is not yet supported in the TF-RMM, and thus must be disabled using
>>>> --disable-sve
>>>>
>>>> You may also run the kvm-unit-tests inside the Realm world, using the similar
>>>> options as above.
>>>
>>> Building all of these components and configuring the FVP correctly can be quite
>>> tricky, so I thought I would plug a tool we have called Shrinkwrap, which can
>>> simplify all of this.
>>>
>>> The tool accepts a yaml input configuration that describes how a set of
>>> components should be built and packaged, and how the FVP should be configured
>>> and booted. And by default, it uses a Docker container on its backend, which
>>> contains all the required tools, including the FVP. You can optionally use
>>> Podman or have it run on your native system if you prefer. It supports both
>>> x86_64 and aarch64. And you can even run it in --dry-run mode to see the set of
>>> shell commands that would have been executed.
>>>
>>> It comes with two CCA configs out-of-the-box; cca-3world.yaml builds TF-A, RMM,
>>> Linux (for both host and guest), kvmtool and kvm-unit-tests. cca-4world.yaml
>>> adds Hafnium and some demo SPs for the secure world (although since Hafnium
>>> requires x86_64 to build, cca-4world.yaml doesn't currently work on an aarch64
>>> build host).
>>>
>>> See the documentation [1] and repository [2] for more info.
>>>
>>> Brief instructions to get you up and running:
>>>
>>> # Install shrinkwrap. (I assume you have Docker installed):
>>> sudo pip3 install pyyaml termcolor tuxmake
>>> git clone https://git.gitlab.arm.com/tooling/shrinkwrap.git
>>> export PATH=$PWD/shrinkwrap/shrinkwrap:$PATH
>>>
>>> # If running Python < 3.9:
>>> sudo pip3 install graphlib-backport
>>>
>>> # Build all the CCA components:
>>> shrinkwrap build cca-3world.yaml [--dry-run]
>>
>> This has been working on my Multipass instance on M1, thanks for the tool.
>>
>> Thanks,
>> Itaru.
>
> It took a while though I've just booted an Ubuntu 22.10 disk image
> with the cca-3world.yaml config on M1.

That's good to hear - If you have any feedback (or patches ;-)) for Shrinkwrap
that would improve the experience, do let me know!

>
> Thanks,
> Itaru.
>
>>
>>>
>>> # Run the stack in the FVP:
>>> shrinkwrap run cca-3world.yaml -r ROOTFS=<my_rootfs.ext4> [--dry-run]
>>>
>>> By default, building is done at ~/.shrinkwrap/build/cca-3world and the package
>>> is created at ~/.shrinkwrap/package/cca-3world (this can be changed with
>>> envvars).
>>>
>>> The 'run' command will boot TF-A, RMM and host Linux kernel in the FVP, and
>>> mount the provided rootfs. You will likely want to have copied the userspace
>>> pieces into the rootfs before running, so you can create realms:
>>>
>>> - ~/.shrinkwrap/package/cca-3world/Image (kernel with RMI and RSI support)
>>> - ~/.shrinkwrap/package/cca-3world/lkvm (kvmtool able to launch realms)
>>> - ~/.shrinkwrap/package/cca-3world/kvm-unit-tests.tgz (built kvm-unit-tests)
>>>
>>> Once the FVP is booted to a shell, you can do something like this to launch a
>>> Linux guest in a realm:
>>>
>>> lkvm run --realm --disable-sve -c 1 -m 256 -k Image
>>>
>>> [1] https://shrinkwrap.docs.arm.com
>>> [2] https://gitlab.arm.com/tooling/shrinkwrap
>>>
>>>
>>> _______________________________________________
>>> linux-arm-kernel mailing list
>>> linux-arm-kernel@xxxxxxxxxxxxxxxxxxx
>>> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel