Re: [PATCH v4 19/19] riscv: dts: starfive: Add StarFive JH7110 VisionFive 2 board device tree

From: Emil Renner Berthing
Date: Tue Feb 21 2023 - 10:03:50 EST

Next message: Bartosz Golaszewski: "[PATCH 0/2] arm64: qcom: sa8775p: enable cpufreq"
Previous message: Thorsten Leemhuis: "Re: [PATCH] Revert "venus: firmware: Correct non-pix start and end addresses""
In reply to: Hal Feng: "[PATCH v4 19/19] riscv: dts: starfive: Add StarFive JH7110 VisionFive 2 board device tree"
Next in thread: Hal Feng: "Re: [PATCH v4 19/19] riscv: dts: starfive: Add StarFive JH7110 VisionFive 2 board device tree"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

On Tue, 21 Feb 2023 at 03:47, Hal Feng <hal.feng@xxxxxxxxxxxxxxxx> wrote:
> From: Emil Renner Berthing <kernel@xxxxxxxx>
>
> Add a minimal device tree for StarFive JH7110 VisionFive 2 board
> which has version A and version B. Support booting and basic
> clock/reset/pinctrl/uart drivers.
>
> Acked-by: Conor Dooley <conor.dooley@xxxxxxxxxxxxx>
> Signed-off-by: Emil Renner Berthing <kernel@xxxxxxxx>
> Co-developed-by: Jianlong Huang <jianlong.huang@xxxxxxxxxxxxxxxx>
> Signed-off-by: Jianlong Huang <jianlong.huang@xxxxxxxxxxxxxxxx>
> Co-developed-by: Hal Feng <hal.feng@xxxxxxxxxxxxxxxx>
> Signed-off-by: Hal Feng <hal.feng@xxxxxxxxxxxxxxxx>
> ---
> arch/riscv/boot/dts/starfive/Makefile | 6 +-
> .../jh7110-starfive-visionfive-2-v1.2a.dts | 13 ++
> .../jh7110-starfive-visionfive-2-v1.3b.dts | 13 ++
> .../jh7110-starfive-visionfive-2.dtsi | 215 ++++++++++++++++++
> 4 files changed, 246 insertions(+), 1 deletion(-)
> create mode 100644 arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2-v1.2a.dts
> create mode 100644 arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2-v1.3b.dts
> create mode 100644 arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
>
> diff --git a/arch/riscv/boot/dts/starfive/Makefile b/arch/riscv/boot/dts/starfive/Makefile
> index 039c143cba33..cd73519b907b 100644
> --- a/arch/riscv/boot/dts/starfive/Makefile
> +++ b/arch/riscv/boot/dts/starfive/Makefile
> @@ -1,2 +1,6 @@
> # SPDX-License-Identifier: GPL-2.0
> -dtb-$(CONFIG_SOC_STARFIVE) += jh7100-beaglev-starlight.dtb jh7100-starfive-visionfive-v1.dtb
> +dtb-$(CONFIG_SOC_STARFIVE) += jh7100-beaglev-starlight.dtb
> +dtb-$(CONFIG_SOC_STARFIVE) += jh7100-starfive-visionfive-v1.dtb
> +
> +dtb-$(CONFIG_SOC_STARFIVE) += jh7110-starfive-visionfive-2-v1.2a.dtb
> +dtb-$(CONFIG_SOC_STARFIVE) += jh7110-starfive-visionfive-2-v1.3b.dtb
> diff --git a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2-v1.2a.dts b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2-v1.2a.dts
> new file mode 100644
> index 000000000000..4af3300f3cf3
> --- /dev/null
> +++ b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2-v1.2a.dts
> @@ -0,0 +1,13 @@
> +// SPDX-License-Identifier: GPL-2.0 OR MIT
> +/*
> + * Copyright (C) 2022 StarFive Technology Co., Ltd.
> + * Copyright (C) 2022 Emil Renner Berthing <kernel@xxxxxxxx>
> + */
> +
> +/dts-v1/;
> +#include "jh7110-starfive-visionfive-2.dtsi"
> +
> +/ {
> + model = "StarFive VisionFive 2 v1.2A";
> + compatible = "starfive,visionfive-2-v1.2a", "starfive,jh7110";
> +};
> diff --git a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2-v1.3b.dts b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2-v1.3b.dts
> new file mode 100644
> index 000000000000..9230cc3d8946
> --- /dev/null
> +++ b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2-v1.3b.dts
> @@ -0,0 +1,13 @@
> +// SPDX-License-Identifier: GPL-2.0 OR MIT
> +/*
> + * Copyright (C) 2022 StarFive Technology Co., Ltd.
> + * Copyright (C) 2022 Emil Renner Berthing <kernel@xxxxxxxx>
> + */
> +
> +/dts-v1/;
> +#include "jh7110-starfive-visionfive-2.dtsi"
> +
> +/ {
> + model = "StarFive VisionFive 2 v1.3B";
> + compatible = "starfive,visionfive-2-v1.3b", "starfive,jh7110";
> +};
> diff --git a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
> new file mode 100644
> index 000000000000..c2aa8946a0f1
> --- /dev/null
> +++ b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
> @@ -0,0 +1,215 @@
> +// SPDX-License-Identifier: GPL-2.0 OR MIT
> +/*
> + * Copyright (C) 2022 StarFive Technology Co., Ltd.
> + * Copyright (C) 2022 Emil Renner Berthing <kernel@xxxxxxxx>
> + */
> +
> +/dts-v1/;
> +#include "jh7110.dtsi"
> +#include "jh7110-pinfunc.h"
> +#include <dt-bindings/gpio/gpio.h>
> +
> +/ {
> + aliases {
> + serial0 = &uart0;
> + i2c0 = &i2c0;
> + i2c2 = &i2c2;
> + i2c5 = &i2c5;
> + i2c6 = &i2c6;

Let's keep these sorted alphabetically.

> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + cpus {
> + timebase-frequency = <4000000>;
> + };
> +
> + memory@40000000 {
> + device_type = "memory";
> + reg = <0x0 0x40000000 0x1 0x0>;
> + };
> +
> + gpio-restart {
> + compatible = "gpio-restart";
> + gpios = <&sysgpio 35 GPIO_ACTIVE_HIGH>;
> + priority = <224>;
> + };
> +};
> +
> +&osc {
> + clock-frequency = <24000000>;
> +};
> +
> +&rtc_osc {
> + clock-frequency = <32768>;
> +};
> +
> +&gmac0_rmii_refin {
> + clock-frequency = <50000000>;
> +};
> +
> +&gmac0_rgmii_rxin {
> + clock-frequency = <125000000>;
> +};
> +
> +&gmac1_rmii_refin {
> + clock-frequency = <50000000>;
> +};
> +
> +&gmac1_rgmii_rxin {
> + clock-frequency = <125000000>;
> +};
> +
> +&i2stx_bclk_ext {
> + clock-frequency = <12288000>;
> +};
> +
> +&i2stx_lrck_ext {
> + clock-frequency = <192000>;
> +};
> +
> +&i2srx_bclk_ext {
> + clock-frequency = <12288000>;
> +};
> +
> +&i2srx_lrck_ext {
> + clock-frequency = <192000>;
> +};
> +
> +&tdm_ext {
> + clock-frequency = <49152000>;
> +};
> +
> +&mclk_ext {
> + clock-frequency = <12288000>;
> +};
> +
> +&uart0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart0_pins>;
> + status = "okay";
> +};
> +
> +&i2c0 {
> + clock-frequency = <100000>;
> + i2c-sda-hold-time-ns = <300>;
> + i2c-sda-falling-time-ns = <510>;
> + i2c-scl-falling-time-ns = <510>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c0_pins>;
> + status = "okay";
> +};
> +
> +&i2c2 {
> + clock-frequency = <100000>;
> + i2c-sda-hold-time-ns = <300>;
> + i2c-sda-falling-time-ns = <510>;
> + i2c-scl-falling-time-ns = <510>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c2_pins>;
> + status = "okay";
> +};
> +
> +&i2c5 {
> + clock-frequency = <100000>;
> + i2c-sda-hold-time-ns = <300>;
> + i2c-sda-falling-time-ns = <510>;
> + i2c-scl-falling-time-ns = <510>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c5_pins>;
> + status = "okay";
> +};
> +
> +&i2c6 {
> + clock-frequency = <100000>;
> + i2c-sda-hold-time-ns = <300>;
> + i2c-sda-falling-time-ns = <510>;
> + i2c-scl-falling-time-ns = <510>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c6_pins>;
> + status = "okay";
> +};
> +
> +&sysgpio {
> + uart0_pins: uart0-0 {
> + tx-pins {
> + pinmux = <GPIOMUX(5, GPOUT_SYS_UART0_TX,
> + GPOEN_ENABLE,
> + GPI_NONE)>;
> + bias-disable;
> + drive-strength = <12>;
> + input-disable;
> + input-schmitt-disable;
> + slew-rate = <0>;
> + };
> +
> + rx-pins {
> + pinmux = <GPIOMUX(6, GPOUT_LOW,
> + GPOEN_DISABLE,
> + GPI_SYS_UART0_RX)>;
> + bias-disable; /* external pull-up */
> + drive-strength = <2>;
> + input-enable;
> + input-schmitt-enable;
> + slew-rate = <0>;
> + };
> + };
> +
> + i2c0_pins: i2c0-0 {
> + i2c-pins {
> + pinmux = <GPIOMUX(57, GPOUT_LOW,
> + GPOEN_SYS_I2C0_CLK,
> + GPI_SYS_I2C0_CLK)>,
> + <GPIOMUX(58, GPOUT_LOW,
> + GPOEN_SYS_I2C0_DATA,
> + GPI_SYS_I2C0_DATA)>;
> + bias-disable; /* external pull-up */
> + input-enable;
> + input-schmitt-enable;
> + };
> + };
> +
> + i2c2_pins: i2c2-0 {
> + i2c-pins {
> + pinmux = <GPIOMUX(3, GPOUT_LOW,
> + GPOEN_SYS_I2C2_CLK,
> + GPI_SYS_I2C2_CLK)>,
> + <GPIOMUX(2, GPOUT_LOW,
> + GPOEN_SYS_I2C2_DATA,
> + GPI_SYS_I2C2_DATA)>;
> + bias-disable; /* external pull-up */
> + input-enable;
> + input-schmitt-enable;
> + };
> + };
> +
> + i2c5_pins: i2c5-0 {
> + i2c-pins {
> + pinmux = <GPIOMUX(19, GPOUT_LOW,
> + GPOEN_SYS_I2C5_CLK,
> + GPI_SYS_I2C5_CLK)>,
> + <GPIOMUX(20, GPOUT_LOW,
> + GPOEN_SYS_I2C5_DATA,
> + GPI_SYS_I2C5_DATA)>;
> + bias-disable; /* external pull-up */
> + input-enable;
> + input-schmitt-enable;
> + };
> + };
> +
> + i2c6_pins: i2c6-0 {
> + i2c-pins {
> + pinmux = <GPIOMUX(16, GPOUT_LOW,
> + GPOEN_SYS_I2C6_CLK,
> + GPI_SYS_I2C6_CLK)>,
> + <GPIOMUX(17, GPOUT_LOW,
> + GPOEN_SYS_I2C6_DATA,
> + GPI_SYS_I2C6_DATA)>;
> + bias-disable; /* external pull-up */
> + input-enable;
> + input-schmitt-enable;
> + };
> + };
> +};

It would be great to have some sort of order to this file so it's
obvious where to add new nodes. I suggest we do
- root node
- external clocks
- other node references in alphabetical order

You're almost there with this patch except the uart0 node is out of place.

/Emil

> 2.38.1
>

Next message: Bartosz Golaszewski: "[PATCH 0/2] arm64: qcom: sa8775p: enable cpufreq"
Previous message: Thorsten Leemhuis: "Re: [PATCH] Revert "venus: firmware: Correct non-pix start and end addresses""
In reply to: Hal Feng: "[PATCH v4 19/19] riscv: dts: starfive: Add StarFive JH7110 VisionFive 2 board device tree"
Next in thread: Hal Feng: "Re: [PATCH v4 19/19] riscv: dts: starfive: Add StarFive JH7110 VisionFive 2 board device tree"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]