Re: [PATCH v5 11/12] riscv: dts: starfive: visionfive-2-v1.2a: Add gmac+phy's delay configuration

[Guo Samin]

在 2023/3/6 21:00:19, Emil Renner Berthing 写道:
> On Fri, 3 Mar 2023 at 10:01, Samin Guo <samin.guo@xxxxxxxxxxxxxxxx> wrote:
>> v1.2A gmac0 uses motorcomm YT8531(rgmii-id) PHY, and needs delay
>> configurations.
>>
>> v1.2A gmac1 uses motorcomm YT8512(rmii) PHY, and needs to
>> switch rx and rx to external clock sources.
>>
>> Signed-off-by: Samin Guo <samin.guo@xxxxxxxxxxxxxxxx>
>> ---
>>  .../starfive/jh7110-starfive-visionfive-2-v1.2a.dts | 13 +++++++++++++
>>  1 file changed, 13 insertions(+)
>>
>> diff --git a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2-v1.2a.dts b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2-v1.2a.dts
>> index 4af3300f3cf3..205a13d8c8b1 100644
>> --- a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2-v1.2a.dts
>> +++ b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2-v1.2a.dts
>> @@ -11,3 +11,16 @@
>>         model = "StarFive VisionFive 2 v1.2A";
>>         compatible = "starfive,visionfive-2-v1.2a", "starfive,jh7110";
>>  };
>> +
>> +&gmac1 {
>> +       phy-mode = "rmii";
>> +       assigned-clocks = <&syscrg JH7110_SYSCLK_GMAC1_TX>,
>> +                         <&syscrg JH7110_SYSCLK_GMAC1_RX>;
>> +       assigned-clock-parents = <&syscrg JH7110_SYSCLK_GMAC1_RMII_RTX>,
>> +                                <&syscrg JH7110_SYSCLK_GMAC1_RMII_RTX>;
>> +};
>> +
>> +&phy0 {
>> +       rx-internal-delay-ps = <1900>;
>> +       tx-internal-delay-ps = <1350>;
>> +};
> 
> Here you're not specifying the internal delays for phy1 which means it
> defaults to 1950ps for both rx and tx. Is that right or did you mean
> to set them to 0 like the v1.3b phy1?

Hi, emil, usually, only 1000M (rgmii) needs to configure the delay, and 100M(rmii) does not.
> 
> Also your u-boot seems to set what the linux phy driver calls
> motorcomm,keep-pll-enabled and motorcomm,auto-sleep-disabled for all
> the phys. Did you leave those out on purpose?

Hi, Emil, We did configure motorcomm,auto-sleep-disabled for yt8512 in uboot, 
but Yutai upstream's Linux driver only yt8521/yt8531 supports this property. 
Yt8512 is a Generic PHY driver and does not support the configuration of 
motorcomm,auto-sleep-disabled and motorcomm,keep-pll-enabled.

And without configuring these two attributes, vf2-1.2a gmac1 also works normally.


Best regards,
Samin
> 
>> --
>> 2.17.1
>>
>>
>> _______________________________________________
>> linux-riscv mailing list
>> linux-riscv@xxxxxxxxxxxxxxxxxxx
>> http://lists.infradead.org/mailman/listinfo/linux-riscv

-- 
Best regards,
Samin