Re: [PATCH v2] arm64: dts: qcom: sdm845-oneplus-common: add PN553 NFC

[Konrad Dybcio]

On 7.03.2023 19:59, Gergo Koteles wrote:
> The OnePlus 6/6T both have a NQ330 (PN553 + P73N2M0).
> The PN533 supported by the nxp-nci-i2c driver in mainline.
> It detects/reads NFC tags using "nfctool".
> 
> Signed-off-by: Gergo Koteles <soyer@xxxxxx>
> ---
Next time include a changelog below this --- line detailing
what changed between revisions.

Reviewed-by: Konrad Dybcio <konrad.dybcio@xxxxxxxxxx>

Konrad
>  .../boot/dts/qcom/sdm845-oneplus-common.dtsi  | 39 +++++++++++++++++++
>  1 file changed, 39 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi b/arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi
> index 64638ea94db7..5e45801031d8 100644
> --- a/arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi
> @@ -380,6 +380,24 @@ zap-shader {
>  	};
>  };
>  
> +&i2c3 {
> +	clock-frequency = <400000>;
> +	status = "okay";
> +
> +	nfc@28 {
> +		compatible = "nxp,nxp-nci-i2c";
> +		reg = <0x28>;
> +
> +		interrupts-extended = <&tlmm 63 IRQ_TYPE_EDGE_RISING>;
> +
> +		enable-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>;
> +		firmware-gpios = <&tlmm 62 GPIO_ACTIVE_HIGH>;
> +
> +		pinctrl-0 = <&nfc_int_active &nfc_enable_active &nfc_firmware_active>;
> +		pinctrl-names = "default";
> +	};
> +};
> +
>  &i2c10 {
>  	status = "okay";
>  	clock-frequency = <100000>;
> @@ -753,6 +771,27 @@ &usb_1_hsphy {
>  &tlmm {
>  	gpio-reserved-ranges = <0 4>, <81 4>;
>  
> +	nfc_int_active: nfc-int-active-state {
> +		pins = "gpio63";
> +		function = "gpio";
> +		drive-strength = <2>;
> +		bias-pull-up;
> +	};
> +
> +	nfc_enable_active: nfc-enable-active-state {
> +		pins = "gpio12";
> +		function = "gpio";
> +		drive-strength = <2>;
> +		bias-pull-up;
> +	};
> +
> +	nfc_firmware_active: nfc-firmware-active-state {
> +		pins = "gpio62";
> +		function = "gpio";
> +		drive-strength = <2>;
> +		bias-pull-up;
> +	};
> +
>  	tri_state_key_default: tri-state-key-default-state {
>  		pins = "gpio40", "gpio42", "gpio26";
>  		function = "gpio";