Re: [PATCH v2] ARM: dts: aspeed: mtmitchell: Enable NCSI

[Chanh Nguyen]

On 01/03/2023 07:17, Joel Stanley wrote:
> On Tue, 28 Feb 2023 at 10:28, Chanh Nguyen <chanh@xxxxxxxxxxxxxxxxxxxxxx> wrote:
> > Support the mac3 (RGMII4) as an NC-SI stack instead of an MDIO PHY.
> >
> > The OCP slot #0 and OCP slot #1 use a common the BMC_NCSI signal,
> > so we use only one of them at the same time. The OCP slot #0 will
> > be enabled by PCA9539's setting by default.
> >
> > Also, enable the OCP Auxiliary Power during booting.
> >
> > Signed-off-by: Chanh Nguyen <chanh@xxxxxxxxxxxxxxxxxxxxxx>
>
> LGTM. I'll apply it once we have a -rc1.
>
> Reviewed-by: Joel Stanley <joel@xxxxxxxxx>

Thank Joel very much!

> > ---
> > Changes in v2:
> >     - Change PCA9539APW node name.                     [Krzysztof]
> > ---
> >   .../boot/dts/aspeed-bmc-ampere-mtmitchell.dts | 37 ++++++++++++++++++-
> >   1 file changed, 36 insertions(+), 1 deletion(-)
> >
> > diff --git a/arch/arm/boot/dts/aspeed-bmc-ampere-mtmitchell.dts b/arch/arm/boot/dts/aspeed-bmc-ampere-mtmitchell.dts
> > index 4b91600eaf62..1e0e88465254 100644
> > --- a/arch/arm/boot/dts/aspeed-bmc-ampere-mtmitchell.dts
> > +++ b/arch/arm/boot/dts/aspeed-bmc-ampere-mtmitchell.dts
> > @@ -251,6 +251,14 @@
> >          pinctrl-0 = <&pinctrl_rgmii1_default>;
> >   };
> >
> > +&mac3 {
> > +       status = "okay";
> > +       pinctrl-names = "default";
> > +       pinctrl-0 = <&pinctrl_rmii4_default>;
> > +       clock-names = "MACCLK", "RCLK";
> > +       use-ncsi;
> > +};
> > +
> >   &fmc {
> >          status = "okay";
> >          flash@0 {
> > @@ -439,6 +447,26 @@
> >          status = "okay";
> >   };
> >
> > +&i2c8 {
> > +       status = "okay";
> > +
> > +       gpio@77 {
> > +               compatible = "nxp,pca9539";
> > +               reg = <0x77>;
> > +               gpio-controller;
> > +               #address-cells = <1>;
> > +               #size-cells = <0>;
> > +               #gpio-cells = <2>;
> > +
> > +               bmc-ocp0-en-hog {
> > +                       gpio-hog;
> > +                       gpios = <7 GPIO_ACTIVE_LOW>;
> > +                       output-high;
> > +                       line-name = "bmc-ocp0-en-n";
> > +               };
> > +       };
> > +};
> > +
> >   &i2c9 {
> >          status = "okay";
> >   };
> > @@ -530,13 +558,20 @@
> >          /*V0-V7*/       "s0-hightemp-n","s0-fault-alert","s0-sys-auth-failure-n",
> >                          "host0-reboot-ack-n","host0-ready","host0-shd-req-n",
> >                          "host0-shd-ack-n","s0-overtemp-n",
> > -       /*W0-W7*/       "ocp-aux-pwren","ocp-main-pwren","ocp-pgood","",
> > +       /*W0-W7*/       "","ocp-main-pwren","ocp-pgood","",
> >                          "bmc-ok","bmc-ready","spi0-program-sel","spi0-backup-sel",
> >          /*X0-X7*/       "i2c-backup-sel","s1-fault-alert","s1-fw-boot-ok",
> >                          "s1-hightemp-n","s0-spi-auth-fail-n","s1-sys-auth-failure-n",
> >                          "s1-overtemp-n","s1-spi-auth-fail-n",
> >          /*Y0-Y7*/       "","","","","","","","host0-special-boot",
> >          /*Z0-Z7*/       "reset-button","ps0-pgood","ps1-pgood","","","","","";
> > +
> > +       ocp-aux-pwren-hog {
> > +               gpio-hog;
> > +               gpios = <ASPEED_GPIO(W, 0) GPIO_ACTIVE_HIGH>;
> > +               output-high;
> > +               line-name = "ocp-aux-pwren";
> > +       };
> >   };
> >
> >   &gpio1 {
> > --
> > 2.17.1