Re: [PATCH] USB: serial: xr: Add TIOCGRS485 and TIOCSRS485 ioctls

[Jarkko Sonninen]

On 3/13/23 09:00, Greg Kroah-Hartman wrote:
> Nit, your "To:" line was corrupted :(
>
> On Mon, Mar 13, 2023 at 03:04:16AM +0200, Jarkko Sonninen wrote:
> > Add support for RS-485 in Exar USB adapters.
> > RS-485 mode is controlled by TIOCGRS485 and TIOCSRS485 ioctls.
> > Gpio mode register is set to enable RS-485.
> >
> > Signed-off-by: Jarkko Sonninen <kasper@xxxxxx>
> > ---
> >   drivers/usb/serial/xr_serial.c | 72 +++++++++++++++++++++++++++++++++-
> >   1 file changed, 71 insertions(+), 1 deletion(-)
> >
> > diff --git a/drivers/usb/serial/xr_serial.c b/drivers/usb/serial/xr_serial.c
> > index fdb0aae546c3..edbb6add087c 100644
> > --- a/drivers/usb/serial/xr_serial.c
> > +++ b/drivers/usb/serial/xr_serial.c
> > @@ -93,6 +93,7 @@ struct xr_txrx_clk_mask {
> >   #define XR_GPIO_MODE_SEL_DTR_DSR	0x2
> >   #define XR_GPIO_MODE_SEL_RS485		0x3
> >   #define XR_GPIO_MODE_SEL_RS485_ADDR	0x4
> > +#define XR_GPIO_MODE_RS485_TX_H		0x8
> >   #define XR_GPIO_MODE_TX_TOGGLE		0x100
> >   #define XR_GPIO_MODE_RX_TOGGLE		0x200
> >   
> > @@ -237,6 +238,8 @@ static const struct xr_type xr_types[] = {
> >   struct xr_data {
> >   	const struct xr_type *type;
> >   	u8 channel;			/* zero-based index or interface number */
> > +	struct serial_rs485 rs485;
> > +	spinlock_t lock;
> >   };
> >   
> >   static int xr_set_reg(struct usb_serial_port *port, u8 channel, u16 reg, u16 val)
> > @@ -629,6 +632,7 @@ static void xr_set_flow_mode(struct tty_struct *tty,
> >   	struct xr_data *data = usb_get_serial_port_data(port);
> >   	const struct xr_type *type = data->type;
> >   	u16 flow, gpio_mode;
> > +	unsigned long flags, rs485_flags;
> >   	int ret;
> >   
> >   	ret = xr_get_reg_uart(port, type->gpio_mode, &gpio_mode);
> > @@ -645,9 +649,16 @@ static void xr_set_flow_mode(struct tty_struct *tty,
> >   	/* Set GPIO mode for controlling the pins manually by default. */
> >   	gpio_mode &= ~XR_GPIO_MODE_SEL_MASK;
> >   
> > +	spin_lock_irqsave(&data->lock, flags);
> > +	rs485_flags = data->rs485.flags;
> > +	spin_unlock_irqrestore(&data->lock, flags);
> > +	if (rs485_flags & SER_RS485_ENABLED)
> > +		gpio_mode |= XR_GPIO_MODE_SEL_RS485 | XR_GPIO_MODE_RS485_TX_H;
> > +	else if (C_CRTSCTS(tty) && C_BAUD(tty) != B0)
> > +		gpio_mode |= XR_GPIO_MODE_SEL_RTS_CTS;
> > +
> >   	if (C_CRTSCTS(tty) && C_BAUD(tty) != B0) {
> >   		dev_dbg(&port->dev, "Enabling hardware flow ctrl\n");
> > -		gpio_mode |= XR_GPIO_MODE_SEL_RTS_CTS;
> >   		flow = XR_UART_FLOW_MODE_HW;
> >   	} else if (I_IXON(tty)) {
> >   		u8 start_char = START_CHAR(tty);
> > @@ -827,6 +838,64 @@ static void xr_set_termios(struct tty_struct *tty,
> >   	xr_set_flow_mode(tty, port, old_termios);
> >   }
> >   
> > +static int xr_get_rs485_config(struct tty_struct *tty,
> > +			 unsigned int __user *argp)
> > +{
> > +	struct usb_serial_port *port = tty->driver_data;
> > +	struct xr_data *data = usb_get_serial_port_data(port);
> > +	unsigned long flags;
> > +	struct serial_rs485 rs485;
> > +
> > +	spin_lock_irqsave(&data->lock, flags);
> > +	memcpy(&rs485, &data->rs485, sizeof(rs485));
> Why are you using the stack for this?  Why not directly access the real
> structure instead?  And are you sure you need a lock?  If so, why?

I suppose the lock is not really needed and I'll change this. I was 
unsure about it.

> > +	spin_unlock_irqrestore(&data->lock, flags);
> > +	dev_dbg(tty->dev, "%s flags %02x\n", __func__, rs485.flags);
> dev_dbg() provides __func__ for free, so you never need to provide it
> again.  Just use the +f flag when enabling it from userspace.
>
> > +
> > +	if (copy_to_user(argp, &rs485, sizeof(rs485)))
> > +		return -EFAULT;
> > +
> > +	return 0;
> > +}
> > +
> > +static int xr_set_rs485_config(struct tty_struct *tty,
> > +			 unsigned long __user *argp)
> > +{
> > +	struct usb_serial_port *port = tty->driver_data;
> > +	struct xr_data *data = usb_get_serial_port_data(port);
> > +	struct serial_rs485 rs485;
> > +	unsigned long flags;
> > +
> > +	if (copy_from_user(&rs485, argp, sizeof(rs485)))
> > +		return -EFAULT;
> > +
> > +	dev_dbg(tty->dev, "%s flags %02x\n", __func__, rs485.flags);
> Again, no need for __func__.
>
> > +	rs485.flags &= SER_RS485_ENABLED;
> > +	spin_lock_irqsave(&data->lock, flags);
> > +	memcpy(&data->rs485, &rs485, sizeof(rs485));
> > +	spin_unlock_irqrestore(&data->lock, flags);
> > +	xr_set_flow_mode(tty, port, 0);
> > +
> > +	if (copy_to_user(argp, &data->rs485, sizeof(data->rs485)))
> > +		return -EFAULT;
> > +
> > +	return 0;
> > +}
> > +
> > +
> > +static int xr_ioctl(struct tty_struct *tty,
> > +					unsigned int cmd, unsigned long arg)
> Very odd indentation, please fix up.
>
> > +{
> > +	void __user *argp = (void __user *)arg;
> > +
> > +	switch (cmd) {
> > +	case TIOCGRS485:
> > +		return xr_get_rs485_config(tty, argp);
> > +	case TIOCSRS485:
> > +		return xr_set_rs485_config(tty, argp);
> > +	}
> > +	return -ENOIOCTLCMD;
> Wrong ioctl return value :(

What is the correct ioctl error return value ?
ENOIOCTLCMD was used in most places in usb serial as an error return.


> thanks,
>
> greg k-h

    - Jarkko