[PATCH v2] arm64: dts: qcom: sm6115: Move SDHC node(s)'s 'pinctrl' properties to dts

[Bhupesh Sharma]

Normally the 'pinctrl' properties of a SDHC controller and the
chip detect pin settings are dependent on the type of the slots
(for e.g uSD card slot), regulators and GPIO(s) available on the
board(s).

So, move the same from the sm6115 dtsi file to the respective
board file(s).

Reviewed-by: Marijn Suijten <marijn.suijten@xxxxxxxxxxxxxx>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@xxxxxxxxxx>
---
Changes since v1:
- v1 can be seen here: https://lore.kernel.org/linux-arm-msm/20221220113616.1556097-1-bhupesh.sharma@xxxxxxxxxx/
- Colleted the R-B from Marijn.
- Rebased on linux-next/master

 .../boot/dts/qcom/sm4250-oneplus-billie2.dts  | 10 +++++++++
 arch/arm64/boot/dts/qcom/sm6115.dtsi          | 22 -------------------
 2 files changed, 10 insertions(+), 22 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/sm4250-oneplus-billie2.dts b/arch/arm64/boot/dts/qcom/sm4250-oneplus-billie2.dts
index a3f1c7c41fd73..329eb496bbc5f 100644
--- a/arch/arm64/boot/dts/qcom/sm4250-oneplus-billie2.dts
+++ b/arch/arm64/boot/dts/qcom/sm4250-oneplus-billie2.dts
@@ -202,12 +202,22 @@ &sdhc_2 {
 	vqmmc-supply = <&vreg_l5a>;
 
 	cd-gpios = <&tlmm 88 GPIO_ACTIVE_HIGH>;
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc2_state_on &sdc2_card_det_n>;
+	pinctrl-1 = <&sdc2_state_off &sdc2_card_det_n>;
 
 	status = "okay";
 };
 
 &tlmm {
 	gpio-reserved-ranges = <14 4>;
+
+	sdc2_card_det_n: sd-card-det-n-state {
+		pins = "gpio88";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-up;
+	};
 };
 
 &ufs_mem_hc {
diff --git a/arch/arm64/boot/dts/qcom/sm6115.dtsi b/arch/arm64/boot/dts/qcom/sm6115.dtsi
index fbd67d2c8d781..e8e5f2cafebb9 100644
--- a/arch/arm64/boot/dts/qcom/sm6115.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm6115.dtsi
@@ -595,13 +595,6 @@ data-pins {
 					bias-pull-up;
 					drive-strength = <10>;
 				};
-
-				sd-cd-pins {
-					pins = "gpio88";
-					function = "gpio";
-					bias-pull-up;
-					drive-strength = <2>;
-				};
 			};
 
 			sdc2_state_off: sdc2-off-state {
@@ -622,13 +615,6 @@ data-pins {
 					bias-pull-up;
 					drive-strength = <2>;
 				};
-
-				sd-cd-pins {
-					pins = "gpio88";
-					function = "gpio";
-					bias-disable;
-					drive-strength = <2>;
-				};
 			};
 		};
 
@@ -731,10 +717,6 @@ sdhc_1: mmc@4744000 {
 				 <&gcc GCC_SDCC1_ICE_CORE_CLK>;
 			clock-names = "iface", "core", "xo", "ice";
 
-			pinctrl-0 = <&sdc1_state_on>;
-			pinctrl-1 = <&sdc1_state_off>;
-			pinctrl-names = "default", "sleep";
-
 			bus-width = <8>;
 			status = "disabled";
 		};
@@ -753,10 +735,6 @@ sdhc_2: mmc@4784000 {
 				 <&rpmcc RPM_SMD_XO_CLK_SRC>;
 			clock-names = "iface", "core", "xo";
 
-			pinctrl-0 = <&sdc2_state_on>;
-			pinctrl-1 = <&sdc2_state_off>;
-			pinctrl-names = "default", "sleep";
-
 			power-domains = <&rpmpd SM6115_VDDCX>;
 			operating-points-v2 = <&sdhc2_opp_table>;
 			iommus = <&apps_smmu 0x00a0 0x0>;
-- 
2.38.1