Re: [PATCH -next v6 2/2] mm/zswap: delay the initializaton of zswap

[Liu Shixin]

On 2023/3/23 16:04, Christoph Hellwig wrote:
> On Wed, Mar 22, 2023 at 06:20:06PM +0800, Liu Shixin wrote:
>> Since some users may not use zswap, the zswap_pool is wasted. Save memory
>> by delaying the initialization of zswap until enabled.
>>
>> Signed-off-by: Liu Shixin <liushixin2@xxxxxxxxxx>
>> ---
>>  mm/zswap.c | 51 +++++++++++++++++++++++++++++++++++++++++----------
>>  1 file changed, 41 insertions(+), 10 deletions(-)
>>
>> diff --git a/mm/zswap.c b/mm/zswap.c
>> index 09fa956920fa..3aed3b26524a 100644
>> --- a/mm/zswap.c
>> +++ b/mm/zswap.c
>> @@ -81,6 +81,8 @@ static bool zswap_pool_reached_full;
>>  
>>  #define ZSWAP_PARAM_UNSET ""
>>  
>> +static int zswap_setup(void);
>> +
>>  /* Enable/disable zswap */
>>  static bool zswap_enabled = IS_ENABLED(CONFIG_ZSWAP_DEFAULT_ON);
>>  static int zswap_enabled_param_set(const char *,
>> @@ -220,6 +222,9 @@ static bool zswap_init_started;
>>  /* fatal error during init */
>>  static bool zswap_init_failed;
>>  
>> +/* used to ensure the integrity of initialization */
>> +static DEFINE_MUTEX(zswap_init_lock);
>> +
>>  /* init completed, but couldn't create the initial pool */
>>  static bool zswap_has_pool;
>>  
>> @@ -272,13 +277,13 @@ static void zswap_update_total_size(void)
>>  **********************************/
>>  static struct kmem_cache *zswap_entry_cache;
>>  
>> -static int __init zswap_entry_cache_create(void)
>> +static int zswap_entry_cache_create(void)
>>  {
>>  	zswap_entry_cache = KMEM_CACHE(zswap_entry, 0);
>>  	return zswap_entry_cache == NULL;
>>  }
> Please add a cleanup patch to remove this helper first, it just
> massivel confuses the reader.
I will, thanks.
>
>> -static void __init zswap_entry_cache_destroy(void)
>> +static void zswap_entry_cache_destroy(void)
>>  {
>>  	kmem_cache_destroy(zswap_entry_cache);
>>  }
> Same here.
>
>> @@ -663,7 +668,7 @@ static struct zswap_pool *zswap_pool_create(char *type, char *compressor)
>>  	return NULL;
>>  }
>>  
>> -static __init struct zswap_pool *__zswap_pool_create_fallback(void)
>> +static struct zswap_pool *__zswap_pool_create_fallback(void)
>>  {
>>  	bool has_comp, has_zpool;
>>  
>> @@ -784,8 +789,15 @@ static int __zswap_param_set(const char *val, const struct kernel_param *kp,
>>  	/* if this is load-time (pre-init) param setting,
>>  	 * don't create a pool; that's done during init.
>>  	 */
>> -	if (!zswap_init_started)
>> -		return param_set_charp(s, kp);
>> +	if (!zswap_init_started) {
>> +		mutex_lock(&zswap_init_lock);
>> +		if (!zswap_init_started) {
>> +			ret = param_set_charp(s, kp);
>> +			mutex_unlock(&zswap_init_lock);
>> +			return ret;
>> +		}
>> +		mutex_unlock(&zswap_init_lock);
>> +	}
> Just take the lock around the whole function.  No need to micro-optimize
> setting a kernel paramter.
I will, thanks.
>
>> @@ -884,6 +896,15 @@ static int zswap_enabled_param_set(const char *val,
>>  	if (res == *(bool *)kp->arg)
>>  		return 0;
>>  
>> +	if (!zswap_init_started && (system_state == SYSTEM_RUNNING)) {
> No need for the inner braces.  But directly looking at
> SYSTEM_RUNNING, especially without a comment is a bit of a mess.
> Is there any better way to deal with this?
I have no idea about better way.
>
> Also the zswap_init_started variable name has always been a bit
> confusing.  If everything around it takes zswap_init_lock now,
> it can be replaced with a check for successful zswap initialization
> as all the initializtion is covered by the lock.  That would really
> help to clean up the code.
I will, thanks.
>
>> +static int zswap_debugfs_init(void)
>>  {
>>  	if (!debugfs_initialized())
>>  		return -ENODEV;
>> @@ -1482,7 +1503,7 @@ static int __init zswap_debugfs_init(void)
>>  	return 0;
>>  }
>>  #else
>> -static int __init zswap_debugfs_init(void)
>> +static int zswap_debugfs_init(void)
> Is there any reason to not just always initialize debugfs and
> only defer the expensive allocations?
It seems there is no need to initialize debugfs if zswap is not used.

>
> .
>