[PATCH 4/9] arm64: dts: qcom: qcm2290: Add most QUPs

From: Konrad Dybcio
Date: Mon Apr 03 2023 - 13:36:50 EST

Next message: Konrad Dybcio: "[PATCH 3/9] arm64: dts: qcom: Add initial QCM2290, PM2250 & RB1 device trees"
Previous message: Konrad Dybcio: "[PATCH 2/9] dt-bindings: arm: qcom: Add QRB2210/QCM2290 and RB1 board"
In reply to: Krzysztof Kozlowski: "Re: [PATCH 2/9] dt-bindings: arm: qcom: Add QRB2210/QCM2290 and RB1 board"
Next in thread: Konrad Dybcio: "[PATCH 3/9] arm64: dts: qcom: Add initial QCM2290, PM2250 & RB1 device trees"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

Add all I2C and SPI hosts, the debug UART port and the related pinctrl.

Signed-off-by: Konrad Dybcio <konrad.dybcio@xxxxxxxxxx>
---
arch/arm64/boot/dts/qcom/qcm2290.dtsi | 294 ++++++++++++++++++++++++++++++++++
1 file changed, 294 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/qcm2290.dtsi b/arch/arm64/boot/dts/qcom/qcm2290.dtsi
index 27d4742cdb19..edfa18190454 100644
--- a/arch/arm64/boot/dts/qcom/qcm2290.dtsi
+++ b/arch/arm64/boot/dts/qcom/qcm2290.dtsi
@@ -310,6 +310,90 @@ tlmm: pinctrl@500000 {
interrupt-controller;
#interrupt-cells = <2>;

+ qup_i2c0_default: qup-i2c0-default-state {
+ pins = "gpio0", "gpio1";
+ function = "qup0";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ qup_i2c1_default: qup-i2c1-default-state {
+ pins = "gpio4", "gpio5";
+ function = "qup1";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ qup_i2c2_default: qup-i2c2-default-state {
+ pins = "gpio6", "gpio7";
+ function = "qup2";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ qup_i2c3_default: qup-i2c3-default-state {
+ pins = "gpio8", "gpio9";
+ function = "qup3";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ qup_i2c4_default: qup-i2c4-default-state {
+ pins = "gpio12", "gpio13";
+ function = "qup4";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ qup_i2c5_default: qup-i2c5-default-state {
+ pins = "gpio14", "gpio15";
+ function = "qup5";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ qup_spi0_default: qup-spi0-default-state {
+ pins = "gpio0", "gpio1","gpio2", "gpio3";
+ function = "qup0";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ qup_spi1_default: qup-spi1-default-state {
+ pins = "gpio4", "gpio5", "gpio69", "gpio70";
+ function = "qup1";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ qup_spi2_default: qup-spi2-default-state {
+ pins = "gpio6", "gpio7", "gpio71", "gpio80";
+ function = "qup2";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ qup_spi3_default: qup-spi3-default-state {
+ pins = "gpio8", "gpio9", "gpio10", "gpio11";
+ function = "qup3";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ qup_spi4_default: qup-spi4-default-state {
+ pins = "gpio12", "gpio13", "gpio96", "gpio97";
+ function = "qup4";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ qup_spi5_default: qup-spi5-default-state {
+ pins = "gpio14", "gpio15", "gpio16", "gpio17";
+ function = "qup5";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
qup_uart0_default: qup-uart0-default-state {
pins = "gpio0", "gpio1", "gpio2", "gpio3";
function = "qup0";
@@ -317,6 +401,13 @@ qup_uart0_default: qup-uart0-default-state {
bias-disable;
};

+ qup_uart4_default: qup-uart4-default-state {
+ pins = "gpio12", "gpio13";
+ function = "qup4";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
sdc1_state_on: sdc1-on-state {
clk-pins {
pins = "sdc1_clk";
@@ -604,6 +695,38 @@ qupv3_id_0: geniqup@4ac0000 {
ranges;
status = "disabled";

+ i2c0: i2c@4a80000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0x04a80000 0x0 0x4000>;
+ interrupts = <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_i2c0_default>;
+ pinctrl-names = "default";
+ dmas = <&gpi_dma0 0 0 QCOM_GPI_I2C>,
+ <&gpi_dma0 1 0 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi0: spi@4a80000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0x04a80000 0x0 0x4000>;
+ interrupts = <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_spi0_default>;
+ pinctrl-names = "default";
+ dmas = <&gpi_dma0 0 0 QCOM_GPI_SPI>,
+ <&gpi_dma0 1 0 QCOM_GPI_SPI>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
uart0: serial@4a80000 {
compatible = "qcom,geni-uart";
reg = <0x0 0x04a80000 0x0 0x4000>;
@@ -614,6 +737,177 @@ uart0: serial@4a80000 {
pinctrl-names = "default";
status = "disabled";
};
+
+ i2c1: i2c@4a84000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0x04a84000 0x0 0x4000>;
+ interrupts = <GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_i2c1_default>;
+ pinctrl-names = "default";
+ dmas = <&gpi_dma0 0 1 QCOM_GPI_I2C>,
+ <&gpi_dma0 1 1 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi1: spi@4a84000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0x04a84000 0x0 0x4000>;
+ interrupts = <GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_spi1_default>;
+ pinctrl-names = "default";
+ dmas = <&gpi_dma0 0 1 QCOM_GPI_SPI>,
+ <&gpi_dma0 1 1 QCOM_GPI_SPI>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c2: i2c@4a88000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0x04a88000 0x0 0x4000>;
+ interrupts = <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_i2c2_default>;
+ pinctrl-names = "default";
+ dmas = <&gpi_dma0 0 2 QCOM_GPI_I2C>,
+ <&gpi_dma0 1 2 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi2: spi@4a88000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0x04a88000 0x0 0x4000>;
+ interrupts = <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_spi2_default>;
+ pinctrl-names = "default";
+ dmas = <&gpi_dma0 0 2 QCOM_GPI_SPI>,
+ <&gpi_dma0 1 2 QCOM_GPI_SPI>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c3: i2c@4a8c000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0x04a8c000 0x0 0x4000>;
+ interrupts = <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_i2c3_default>;
+ pinctrl-names = "default";
+ dmas = <&gpi_dma0 0 3 QCOM_GPI_I2C>,
+ <&gpi_dma0 1 3 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi3: spi@4a8c000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0x04a8c000 0x0 0x4000>;
+ interrupts = <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_spi3_default>;
+ pinctrl-names = "default";
+ dmas = <&gpi_dma0 0 3 QCOM_GPI_SPI>,
+ <&gpi_dma0 1 3 QCOM_GPI_SPI>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c4: i2c@4a90000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0x04a90000 0x0 0x4000>;
+ interrupts = <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_i2c4_default>;
+ pinctrl-names = "default";
+ dmas = <&gpi_dma0 0 4 QCOM_GPI_I2C>,
+ <&gpi_dma0 1 4 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi4: spi@4a90000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0x04a90000 0x0 0x4000>;
+ interrupts = <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi4_default>;
+ dmas = <&gpi_dma0 0 4 QCOM_GPI_SPI>,
+ <&gpi_dma0 1 4 QCOM_GPI_SPI>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ uart4: serial@4a90000 {
+ compatible = "qcom,geni-uart";
+ reg = <0x0 0x04a90000 0x0 0x4000>;
+ interrupts = <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_uart4_default>;
+ pinctrl-names = "default";
+ status = "disabled";
+ };
+
+ i2c5: i2c@4a94000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0x04a94000 0x0 0x4000>;
+ interrupts = <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_i2c5_default>;
+ pinctrl-names = "default";
+ dmas = <&gpi_dma0 0 5 QCOM_GPI_I2C>,
+ <&gpi_dma0 1 5 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spi5: spi@4a94000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0x04a94000 0x0 0x4000>;
+ interrupts = <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_spi5_default>;
+ pinctrl-names = "default";
+ dmas = <&gpi_dma0 0 5 QCOM_GPI_SPI>,
+ <&gpi_dma0 1 5 QCOM_GPI_SPI>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
};

usb: usb@4ef8800 {

--
2.40.0

Next message: Konrad Dybcio: "[PATCH 3/9] arm64: dts: qcom: Add initial QCM2290, PM2250 & RB1 device trees"
Previous message: Konrad Dybcio: "[PATCH 2/9] dt-bindings: arm: qcom: Add QRB2210/QCM2290 and RB1 board"
In reply to: Krzysztof Kozlowski: "Re: [PATCH 2/9] dt-bindings: arm: qcom: Add QRB2210/QCM2290 and RB1 board"
Next in thread: Konrad Dybcio: "[PATCH 3/9] arm64: dts: qcom: Add initial QCM2290, PM2250 & RB1 device trees"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]