Re: [PATCH v5 7/8] arm64: dts: qcom: ipq9574: Add USB related nodes

[Varadarajan Narayanan]

On Fri, Mar 31, 2023 at 12:19:10PM +0200, Johan Hovold wrote:
> On Fri, Mar 31, 2023 at 02:57:11PM +0530, Varadarajan Narayanan wrote:
> > On Thu, Mar 30, 2023 at 12:44:40PM +0300, Dmitry Baryshkov wrote:
> > > On Thu, 30 Mar 2023 at 11:42, Varadarajan Narayanan
> > > <quic_varada@xxxxxxxxxxx> wrote:
> > > >
> > > > Add USB phy and controller related nodes
> > > >
> > > > Signed-off-by: Varadarajan Narayanan <quic_varada@xxxxxxxxxxx>
> > > > ---
> > > >  Changes in v5:
> > > >         - Fix additional comments
> > > >         - Edit nodes to match with qcom,sc8280xp-qmp-usb3-uni-phy.yaml
> > > >         - 'make dtbs_check' giving the following messages since
> > > >           ipq9574 doesn't have power domains. Hope this is ok
> > > >
> > > >                 /local/mnt/workspace/varada/varda-linux/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dtb: phy@7d000: 'power-domains' is a required property
> > > >                 From schema: /local/mnt/workspace/varada/varda-linux/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-usb3-uni-phy.yaml
> > > >                 /local/mnt/workspace/varada/varda-linux/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dtb: usb@8a00000: 'power-domains' is a required property
> > > >                 From schema: /local/mnt/workspace/varada/varda-linux/Documentation/devicetree/bindings/usb/qcom,dwc3.yaml
> > >
> > > No, I think it is not.
> >
> > There are no GDSCs in IPQ9574. Can you suggest how to proceed.
>
> You need to update the binding and either make the power domains
> property optional in the binding or dependent on the SoC.
>
> > > > +               ssphy_0: phy@7d000 {
> > >
> > > Nit: usually the label usb_0_qmpphy
> > >
> > > > +                       compatible = "qcom,ipq9574-qmp-usb3-phy";
> > > > +                       reg = <0x0007d000 0xa00>;
> > > > +                       #phy-cells = <0>;
> > > > +
> > > > +                       clocks = <&gcc GCC_USB0_AUX_CLK>,
> > > > +                                <&xo_board_clk>,
> > > > +                                <&gcc GCC_USB0_PHY_CFG_AHB_CLK>,
> > > > +                                <&gcc GCC_USB0_PIPE_CLK>;
> > > > +                       clock-names = "aux",
> > > > +                                     "ref",
> > > > +                                     "com_aux",
>
> This is not the right name for this clock so you need to update the
> binding first.
>
> Please be more careful.

Thanks for your feedback. Have posted v6 with the above corrections.

-Varada
>
> > > > +                                     "pipe";
> > > > +
> > > > +                       resets = <&gcc GCC_USB0_PHY_BCR>,
> > > > +                                <&gcc GCC_USB3PHY_0_PHY_BCR>;
> > > > +                       reset-names = "phy",
> > > > +                                     "phy_phy";
> > > > +
> > > > +                       vdda-pll-supply = <&reg_usb_1p8>;
> > > > +                       vdda-phy-supply = <&reg_usb_0p925>;
> > > > +
> > > > +                       status = "disabled";
> > > > +
> > > > +                       #clock-cells = <0>;
> > > > +                       clock-output-names = "usb0_pipe_clk";
> > > > +               };
>
> Johan