Re: [PATCH v1 3/3] PCI: brcmstb: Allow setting the completion timeout

[Jim Quinlan]

On Thu, Apr 6, 2023 at 11:59 AM Stefan Wahren <stefan.wahren@xxxxxxxx> wrote:
>
> Hi Jim,
>
> Am 06.04.23 um 14:46 schrieb Jim Quinlan:
> > Since the STB PCIe HW will cause a CPU abort on a completion timeout abort,
> > we might as well extend the timeout limit.  Further, different devices and
> > systems may requires a larger or smaller amount for L1SS exit.
> >
> > Signed-off-by: Jim Quinlan <jim2101024@xxxxxxxxx>
> > ---
> >   drivers/pci/controller/pcie-brcmstb.c | 24 ++++++++++++++++++++++++
> >   1 file changed, 24 insertions(+)
> >
> > diff --git a/drivers/pci/controller/pcie-brcmstb.c b/drivers/pci/controller/pcie-brcmstb.c
> > index 129eee7bdbc1..92d78f4dfaae 100644
> > --- a/drivers/pci/controller/pcie-brcmstb.c
> > +++ b/drivers/pci/controller/pcie-brcmstb.c
> > @@ -1080,6 +1080,29 @@ static void brcm_config_clkreq(struct brcm_pcie *pcie)
> >       writel(clkreq_set, pcie->base + PCIE_MISC_HARD_PCIE_HARD_DEBUG);
> >   }
> >
> > +static void brcm_config_completion_timeout(struct brcm_pcie *pcie)
> > +{
> > +     /* TIMEOUT register is two registers before RGR1_SW_INIT_1 */
> > +     const unsigned int REG_OFFSET = PCIE_RGR1_SW_INIT_1(pcie) - 8;
> > +     u32 timeout, timeout_msec = 1000;
> > +     u64 tmp64;
> > +     int ret;
> > +
> > +     ret = of_property_read_u32(pcie->np, "brcm,completion-abort-msecs",
> > +                                &timeout_msec);
> > +
> > +     if (ret && ret != -EINVAL)
> > +             dev_err(pcie->dev, "bad 'brcm,completion-abort-msecs' prop\n");
>
> i'm not sure about the error behavior. If we want to proceed with
> defaults in such a case, i would make this a warning and mention the
> used defaults.
Will do.

>
> > +
> > +     /* Each unit in timeout register is 1/216,000,000 seconds */
> > +     tmp64 = (u64)216000 * timeout_msec;
> > +
> > +     /* Clamp the requested value before writing it */
> > +     timeout = tmp64 > 0xffffffff ? 0xffffffff : tmp64;
> > +     timeout = timeout < 0xffff ? 0xffff : timeout;
>
> Personally i'm not a huge fan of silently clamping wrong DT values.
I will add a warning with limit info  on clamp and have the YAML min+max.

Thanks
Jim Quinlan
Broadcom STB
>
> Best regards
>
> > +     writel(timeout, pcie->base + REG_OFFSET);
> > +}
> > +
> >   static int brcm_pcie_start_link(struct brcm_pcie *pcie)
> >   {
> >       struct device *dev = pcie->dev;
> > @@ -1110,6 +1133,7 @@ static int brcm_pcie_start_link(struct brcm_pcie *pcie)
> >               return -ENODEV;
> >       }
> >
> > +     brcm_config_completion_timeout(pcie);
> >       brcm_config_clkreq(pcie);
> >
> >       if (pcie->gen)