Re: [PATCH V3 5/5] arm64: dts: qcom: ipq9574: Add cpufreq support

[Konrad Dybcio]

On 7.04.2023 06:53, Devi Priya wrote:
> 
> 
> On 4/7/2023 1:21 AM, Konrad Dybcio wrote:
>>
>>
>> On 6.04.2023 09:00, Devi Priya wrote:
>>> Add cpu freq nodes in the device tree to bump cpu frequency above 800MHz.
>>>
>>> Co-developed-by: Praveenkumar I <quic_ipkumar@xxxxxxxxxxx>
>>> Signed-off-by: Praveenkumar I <quic_ipkumar@xxxxxxxxxxx>
>>> Signed-off-by: Devi Priya <quic_devipriy@xxxxxxxxxxx>
>>> ---
>>>   Changes in V3:
>>>     - No change
>>>
>>>   arch/arm64/boot/dts/qcom/ipq9574.dtsi | 58 +++++++++++++++++++++++++++
>>>   1 file changed, 58 insertions(+)
>>>
>>> diff --git a/arch/arm64/boot/dts/qcom/ipq9574.dtsi b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
>>> index 1f9b7529e7ed..cfef87b5fd22 100644
>>> --- a/arch/arm64/boot/dts/qcom/ipq9574.dtsi
>>> +++ b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
>>> @@ -6,6 +6,7 @@
>>>    * Copyright (c) 2023, Qualcomm Innovation Center, Inc. All rights reserved.
>>>    */
>>>   +#include <dt-bindings/clock/qcom,apss-ipq.h>
>>>   #include <dt-bindings/clock/qcom,ipq9574-gcc.h>
>>>   #include <dt-bindings/interrupt-controller/arm-gic.h>
>>>   #include <dt-bindings/reset/qcom,ipq9574-gcc.h>
>>> @@ -37,6 +38,10 @@
>>>               reg = <0x0>;
>>>               enable-method = "psci";
>>>               next-level-cache = <&L2_0>;
>>> +            clocks = <&apcs_glb APCS_ALIAS0_CORE_CLK>;
>>> +            clock-names = "cpu";
>>> +            operating-points-v2 = <&cpu_opp_table>;
>>> +            cpu-supply = <&ipq9574_s1>;
>>>           };
>>>             CPU1: cpu@1 {
>>> @@ -45,6 +50,10 @@
>>>               reg = <0x1>;
>>>               enable-method = "psci";
>>>               next-level-cache = <&L2_0>;
>>> +            clocks = <&apcs_glb APCS_ALIAS0_CORE_CLK>;
>>> +            clock-names = "cpu";
>>> +            operating-points-v2 = <&cpu_opp_table>;
>>> +            cpu-supply = <&ipq9574_s1>;
>>>           };
>>>             CPU2: cpu@2 {
>>> @@ -53,6 +62,10 @@
>>>               reg = <0x2>;
>>>               enable-method = "psci";
>>>               next-level-cache = <&L2_0>;
>>> +            clocks = <&apcs_glb APCS_ALIAS0_CORE_CLK>;
>>> +            clock-names = "cpu";
>>> +            operating-points-v2 = <&cpu_opp_table>;
>>> +            cpu-supply = <&ipq9574_s1>;
>>>           };
>>>             CPU3: cpu@3 {
>>> @@ -61,6 +74,10 @@
>>>               reg = <0x3>;
>>>               enable-method = "psci";
>>>               next-level-cache = <&L2_0>;
>>> +            clocks = <&apcs_glb APCS_ALIAS0_CORE_CLK>;
>>> +            clock-names = "cpu";
>>> +            operating-points-v2 = <&cpu_opp_table>;
>>> +            cpu-supply = <&ipq9574_s1>;
>>>           };
>>>             L2_0: l2-cache {
>>> @@ -75,6 +92,47 @@
>>>           reg = <0x0 0x40000000 0x0 0x0>;
>>>       };
>>>   +    cpu_opp_table: opp-table-cpu {
>> This is not sorted properly. It should probably come
>> after memory alphabetically ('o' > 'm')
>>
> Yes, But I see that opp-table-cpu node is already placed after
> memory@40000000

Oh you're right, the diff doesn't really show that very
well and I didn't notice..


Reviewed-by: Konrad Dybcio <konrad.dybcio@xxxxxxxxxx>

Konrad
>> Konrad
>>> +        compatible = "operating-points-v2";
>>> +        opp-shared;
>>> +
>>> +        opp-936000000 {
>>> +            opp-hz = /bits/ 64 <936000000>;
>>> +            opp-microvolt = <725000>;
>>> +            clock-latency-ns = <200000>;
>>> +        };
>>> +
>>> +        opp-1104000000 {
>>> +            opp-hz = /bits/ 64 <1104000000>;
>>> +            opp-microvolt = <787500>;
>>> +            clock-latency-ns = <200000>;
>>> +        };
>>> +
>>> +        opp-1416000000 {
>>> +            opp-hz = /bits/ 64 <1416000000>;
>>> +            opp-microvolt = <862500>;
>>> +            clock-latency-ns = <200000>;
>>> +        };
>>> +
>>> +        opp-1488000000 {
>>> +            opp-hz = /bits/ 64 <1488000000>;
>>> +            opp-microvolt = <925000>;
>>> +            clock-latency-ns = <200000>;
>>> +        };
>>> +
>>> +        opp-1800000000 {
>>> +            opp-hz = /bits/ 64 <1800000000>;
>>> +            opp-microvolt = <987500>;
>>> +            clock-latency-ns = <200000>;
>>> +        };
>>> +
>>> +        opp-2208000000 {
>>> +            opp-hz = /bits/ 64 <2208000000>;
>>> +            opp-microvolt = <1062500>;
>>> +            clock-latency-ns = <200000>;
>>> +        };
>>> +    };
>>> +
>>>       firmware {
>>>           scm {
>>>               compatible = "qcom,scm-ipq9574", "qcom,scm";
> Best Regards,
> Devi Priya