[PATCH 09/10] arm64: dts: qcom: sm8250: remove superfluous "input-enable"

[Krzysztof Kozlowski]

Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers.  Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@xxxxxxxxxx>
---
 arch/arm64/boot/dts/qcom/sm8250-sony-xperia-edo.dtsi | 1 -
 arch/arm64/boot/dts/qcom/sm8250.dtsi                 | 7 -------
 2 files changed, 8 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/sm8250-sony-xperia-edo.dtsi b/arch/arm64/boot/dts/qcom/sm8250-sony-xperia-edo.dtsi
index c96cc9c90a5f..2f22d348d45d 100644
--- a/arch/arm64/boot/dts/qcom/sm8250-sony-xperia-edo.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8250-sony-xperia-edo.dtsi
@@ -625,7 +625,6 @@ ts_int_default: ts-int-default-state {
 		function = "gpio";
 		drive-strength = <2>;
 		bias-disable;
-		input-enable;
 	};
 
 	ap2mdm_default: ap2mdm-default-state {
diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi
index 4e7875f8786f..f86660fe7918 100644
--- a/arch/arm64/boot/dts/qcom/sm8250.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi
@@ -2436,7 +2436,6 @@ clk-pins {
 					pins = "gpio10";
 					function = "wsa_swr_clk";
 					drive-strength = <2>;
-					input-enable;
 					bias-pull-down;
 				};
 
@@ -2444,7 +2443,6 @@ data-pins {
 					pins = "gpio11";
 					function = "wsa_swr_data";
 					drive-strength = <2>;
-					input-enable;
 					bias-pull-down;
 				};
 			};
@@ -2460,7 +2458,6 @@ data-pins {
 					pins = "gpio7";
 					function = "dmic1_data";
 					drive-strength = <8>;
-					input-enable;
 				};
 			};
 
@@ -2478,7 +2475,6 @@ data-pins {
 					function = "dmic1_data";
 					drive-strength = <2>;
 					bias-pull-down;
-					input-enable;
 				};
 			};
 
@@ -2523,7 +2519,6 @@ clk-pins {
 					pins = "gpio0";
 					function = "swr_tx_clk";
 					drive-strength = <2>;
-					input-enable;
 					bias-pull-down;
 				};
 
@@ -2531,7 +2526,6 @@ data1-pins {
 					pins = "gpio1";
 					function = "swr_tx_data";
 					drive-strength = <2>;
-					input-enable;
 					bias-bus-hold;
 				};
 
@@ -2539,7 +2533,6 @@ data2-pins {
 					pins = "gpio2";
 					function = "swr_tx_data";
 					drive-strength = <2>;
-					input-enable;
 					bias-pull-down;
 				};
 			};
-- 
2.34.1