[PATCH 1/3] ARM: dts: qcom: apq8026: remove superfluous "input-enable"

[Krzysztof Kozlowski]

Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers.  Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@xxxxxxxxxx>
---
 arch/arm/boot/dts/qcom-apq8026-asus-sparrow.dts    | 2 --
 arch/arm/boot/dts/qcom-apq8026-huawei-sturgeon.dts | 1 -
 arch/arm/boot/dts/qcom-apq8026-lg-lenok.dts        | 3 ---
 3 files changed, 6 deletions(-)

diff --git a/arch/arm/boot/dts/qcom-apq8026-asus-sparrow.dts b/arch/arm/boot/dts/qcom-apq8026-asus-sparrow.dts
index 7a80e1c9f126..aa0e0e8d2a97 100644
--- a/arch/arm/boot/dts/qcom-apq8026-asus-sparrow.dts
+++ b/arch/arm/boot/dts/qcom-apq8026-asus-sparrow.dts
@@ -268,7 +268,6 @@ bluetooth_default_state: bluetooth-default-state {
 		function = "gpio";
 		drive-strength = <8>;
 		bias-disable;
-		input-enable;
 	};
 
 	wlan_hostwake_default_state: wlan-hostwake-default-state {
@@ -276,7 +275,6 @@ wlan_hostwake_default_state: wlan-hostwake-default-state {
 		function = "gpio";
 		drive-strength = <2>;
 		bias-disable;
-		input-enable;
 	};
 
 	wlan_regulator_default_state: wlan-regulator-default-state {
diff --git a/arch/arm/boot/dts/qcom-apq8026-huawei-sturgeon.dts b/arch/arm/boot/dts/qcom-apq8026-huawei-sturgeon.dts
index d64096028ab1..5593a3a60d6c 100644
--- a/arch/arm/boot/dts/qcom-apq8026-huawei-sturgeon.dts
+++ b/arch/arm/boot/dts/qcom-apq8026-huawei-sturgeon.dts
@@ -352,7 +352,6 @@ wlan_hostwake_default_state: wlan-hostwake-default-state {
 		function = "gpio";
 		drive-strength = <2>;
 		bias-disable;
-		input-enable;
 	};
 
 	wlan_regulator_default_state: wlan-regulator-default-state {
diff --git a/arch/arm/boot/dts/qcom-apq8026-lg-lenok.dts b/arch/arm/boot/dts/qcom-apq8026-lg-lenok.dts
index b82381229adf..b887e5361ec3 100644
--- a/arch/arm/boot/dts/qcom-apq8026-lg-lenok.dts
+++ b/arch/arm/boot/dts/qcom-apq8026-lg-lenok.dts
@@ -307,7 +307,6 @@ bluetooth_default_state: bluetooth-default-state {
 		function = "gpio";
 		drive-strength = <2>;
 		bias-disable;
-		input-enable;
 	};
 
 	touch_pins: touch-state {
@@ -317,7 +316,6 @@ irq-pins {
 
 			drive-strength = <8>;
 			bias-pull-down;
-			input-enable;
 		};
 
 		reset-pins {
@@ -335,7 +333,6 @@ wlan_hostwake_default_state: wlan-hostwake-default-state {
 		function = "gpio";
 		drive-strength = <2>;
 		bias-disable;
-		input-enable;
 	};
 
 	wlan_regulator_default_state: wlan-regulator-default-state {
-- 
2.34.1