[PATCH v2 1/1] dt-bindings: iio: pressure: Support Honeywell mprls0025pa sensor

[Andreas Klinger]

Honeywell mpr is a pressure sensor series. There are many different models with different pressure
ranges, units and transfer functions.

The range and transfer function need to be set up in the dt. Therefore new properties
honeywell,pmin-pascal, honeywell,pmax-pascal, honeywell,transfer-function are introduced.

Add dt-bindings.

Signed-off-by: Andreas Klinger <ak@xxxxxxxxxxxxx>
---
 .../iio/pressure/honeywell,mprls0025pa.yaml   | 93 +++++++++++++++++++
 1 file changed, 93 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/iio/pressure/honeywell,mprls0025pa.yaml

diff --git a/Documentation/devicetree/bindings/iio/pressure/honeywell,mprls0025pa.yaml b/Documentation/devicetree/bindings/iio/pressure/honeywell,mprls0025pa.yaml
new file mode 100644
index 000000000000..c0eb3c4be16f
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/pressure/honeywell,mprls0025pa.yaml
@@ -0,0 +1,93 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/pressure/honeywell,mprls0025pa.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Honeywell mpr series pressure sensor
+
+maintainers:
+  - Andreas Klinger <ak@xxxxxxxxxxxxx>
+
+description: |
+  Honeywell pressure sensor of model mprls0025pa.
+
+  This sensor has an I2C and SPI interface. Only the I2C interface is implemented.
+
+  There are many models with different pressure ranges available. The vendor calls them "mpr
+  series". All of them have the identical programming model and differ in the pressure range, unit
+  and transfer function.
+
+  To support different models one need to specify the pressure range as well as the transfer
+  function. Pressure range needs to be converted from its unit to pascal.
+
+  The transfer function defines the ranges of numerical values delivered by the sensor. The minimal
+  range value stands for the minimum pressure and the maximum value also for the maximum pressure
+  with linear relation inside the range.
+
+  Specifications about the devices can be found at:
+    https://prod-edam.honeywell.com/content/dam/honeywell-edam/sps/siot/en-us/products/sensors/
+      pressure-sensors/board-mount-pressure-sensors/micropressure-mpr-series/documents/
+      sps-siot-mpr-series-datasheet-32332628-ciid-172626.pdf
+
+properties:
+  compatible:
+    const: honeywell,mprls0025pa
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  reset-gpios:
+    description:
+      Optional GPIO for resetting the device.
+      If not present the device is not resetted during the probe.
+    maxItems: 1
+
+  honeywell,pmin-pascal:
+    description:
+      Minimum pressure value the sensor can measure in pascal.
+    $ref: /schemas/types.yaml#/definitions/uint32
+
+  honeywell,pmax-pascal:
+    description:
+      Maximum pressure value the sensor can measure in pascal.
+    $ref: /schemas/types.yaml#/definitions/uint32
+
+  honeywell,transfer-function:
+    description:
+      Transfer function which defines the range of valid values delivered by the sensor.
+      1 - A, 10% to 90% of 2^24 (1677722 .. 15099494)
+      2 - B, 2.5% to 22.5% of 2^24 (419430 .. 3774874)
+      3 - C, 20% to 80% of 2^24 (3355443 .. 13421773)
+
+required:
+  - compatible
+  - reg
+  - honeywell,pmin
+  - honeywell,pmax
+  - honeywell,transfer-function
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        pressure@18 {
+            compatible = "honeywell,mprls0025pa";
+            reg = <0x18>;
+            reset-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>;
+            interrupt-parent = <&gpio3>;
+            interrupts = <21 IRQ_TYPE_EDGE_FALLING>;
+            honeywell,pmin = <0>;
+            honeywell,pmax = <172369>;
+            honeywell,transfer-function = <1>;
+        };
+    };
-- 
2.30.2