Re: [RFC PATCH 4/5] arm64: dts: ti: Enable multiple MCAN for AM62x in MCU MCAN overlay

[Nishanth Menon]

On 10:01-20230414, Krzysztof Kozlowski wrote:
> On 14/04/2023 00:30, Judith Mendez wrote:
> > Enable two MCAN in MCU domain. AM62x does not have on-board CAN
> > transcievers, so instead of changing the DTB permanently, add
> > MCU MCAN nodes and transceiver nodes to a MCU MCAN overlay.
> > 
> > If there are no hardware interrupts rounted to the GIC interrupt
> > controller for MCAN IP, A53 Linux will not receive hardware
> > interrupts. If an hrtimer is used to generate software interrupts,
> > the two required interrupt attributes in the MCAN node do not have
> > to be included.
> > 
> > Signed-off-by: Judith Mendez <jm@xxxxxx>
> > ---
> >  arch/arm64/boot/dts/ti/Makefile               |  2 +-
> >  .../boot/dts/ti/k3-am625-sk-mcan-mcu.dtso     | 75 +++++++++++++++++++
> >  2 files changed, 76 insertions(+), 1 deletion(-)
> >  create mode 100644 arch/arm64/boot/dts/ti/k3-am625-sk-mcan-mcu.dtso
> > 
> > diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
> > index abe15e76b614..c76be3888e4d 100644
> > --- a/arch/arm64/boot/dts/ti/Makefile
> > +++ b/arch/arm64/boot/dts/ti/Makefile
> > @@ -9,7 +9,7 @@
> >  # alphabetically.
> >  
> >  # Boards with AM62x SoC
> > -k3-am625-sk-mcan-dtbs := k3-am625-sk.dtb k3-am625-sk-mcan-main.dtbo
> > +k3-am625-sk-mcan-dtbs := k3-am625-sk.dtb k3-am625-sk-mcan-main.dtbo k3-am625-sk-mcan-mcu.dtbo
> >  dtb-$(CONFIG_ARCH_K3) += k3-am625-beagleplay.dtb
> >  dtb-$(CONFIG_ARCH_K3) += k3-am625-sk.dtb
> >  dtb-$(CONFIG_ARCH_K3) += k3-am625-sk-mcan.dtb
> > diff --git a/arch/arm64/boot/dts/ti/k3-am625-sk-mcan-mcu.dtso b/arch/arm64/boot/dts/ti/k3-am625-sk-mcan-mcu.dtso
> > new file mode 100644
> > index 000000000000..777705aea546
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/ti/k3-am625-sk-mcan-mcu.dtso
> > @@ -0,0 +1,75 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/**
> > + * DT overlay for MCAN in MCU domain on AM625 SK
> > + *
> > + * Copyright (C) 2022 Texas Instruments Incorporated - https://www.ti.com/
> > + */
> > +
> > +/dts-v1/;
> > +/plugin/;
> > +
> > +#include <dt-bindings/pinctrl/k3.h>
> > +#include <dt-bindings/soc/ti,sci_pm_domain.h>

NAK.

> > +
> > +
> > +&{/} {
> > +	transceiver2: can-phy1 {
> > +		compatible = "ti,tcan1042";
> > +		#phy-cells = <0>;
> > +		max-bitrate = <5000000>;
> > +	};
> > +
> > +	transceiver3: can-phy2 {
> > +		compatible = "ti,tcan1042";
> > +		#phy-cells = <0>;
> > +		max-bitrate = <5000000>;
> > +	};
> > +};
> > +
> > +&mcu_pmx0 {
> > +	mcu_mcan1_pins_default: mcu-mcan1-pins-default {
> > +		pinctrl-single,pins = <
> > +			AM62X_IOPAD(0x038, PIN_INPUT, 0) /* (B3) MCU_MCAN0_RX */
> > +			AM62X_IOPAD(0x034, PIN_OUTPUT, 0) /* (D6) MCU_MCAN0_TX */
> > +		>;
> > +	};
> > +
> > +	mcu_mcan2_pins_default: mcu-mcan2-pins-default {
> > +		pinctrl-single,pins = <
> > +			AM62X_IOPAD(0x040, PIN_INPUT, 0) /* (D4) MCU_MCAN1_RX */
> > +			AM62X_IOPAD(0x03C, PIN_OUTPUT, 0) /* (E5) MCU_MCAN1_TX */
> > +		>;
> > +	};
> > +};
> > +
> > +&cbass_mcu {
> > +	mcu_mcan1: can@4e00000 {
> > +		compatible = "bosch,m_can";
> > +		reg = <0x00 0x4e00000 0x00 0x8000>,
> > +			  <0x00 0x4e08000 0x00 0x200>;
> > +		reg-names = "message_ram", "m_can";
> > +		power-domains = <&k3_pds 188 TI_SCI_PD_EXCLUSIVE>;
> > +		clocks = <&k3_clks 188 6>, <&k3_clks 188 1>;
> > +		clock-names = "hclk", "cclk";
> > +		bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
> > +		pinctrl-names = "default";
> > +		pinctrl-0 = <&mcu_mcan1_pins_default>;
> > +		phys = <&transceiver2>;
> > +		status = "okay";
> 
> okay is by default. Why do you need it?

mcan is not functional without pinmux, so it has been disabled by
default in SoC. this overlay is supposed to enable it. But this is done
entirely wrongly.


The mcu_mcan1 should first be added to the SoC.dtsi as disabled, then
set to okay with pinctrl and  transciever in the overlay.

-- 
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3  1A34 DDB5 849D 1736 249D