Re: [PATCH 06/10] ARM: dts: qcom: ipq8064: correct LED node names

[Konrad Dybcio]

On 20.04.2023 09:50, Krzysztof Kozlowski wrote:
> GPIO LEDs is not a bus, so drop unit-address and also start suffix
> numbering from 0:
> 
>   Warning (unit_address_vs_reg): /soc/leds/led@7: node has a unit name, but no reg or ranges property
> 
> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@xxxxxxxxxx>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio@xxxxxxxxxx>

Konrad
>  arch/arm/boot/dts/qcom-ipq8064-rb3011.dts |  2 +-
>  arch/arm/boot/dts/qcom-ipq8064-v1.0.dtsi  | 10 +++++-----
>  2 files changed, 6 insertions(+), 6 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/qcom-ipq8064-rb3011.dts b/arch/arm/boot/dts/qcom-ipq8064-rb3011.dts
> index 47a5d1849c72..52eadefd2fb4 100644
> --- a/arch/arm/boot/dts/qcom-ipq8064-rb3011.dts
> +++ b/arch/arm/boot/dts/qcom-ipq8064-rb3011.dts
> @@ -203,7 +203,7 @@ leds {
>  			pinctrl-0 = <&leds_pins>;
>  			pinctrl-names = "default";
>  
> -			led@7 {
> +			led-0 {
>  				label = "rb3011:green:user";
>  				color = <LED_COLOR_ID_GREEN>;
>  				gpios = <&qcom_pinmux 33 GPIO_ACTIVE_HIGH>;
> diff --git a/arch/arm/boot/dts/qcom-ipq8064-v1.0.dtsi b/arch/arm/boot/dts/qcom-ipq8064-v1.0.dtsi
> index 411c8d63c38e..c5abe7151f14 100644
> --- a/arch/arm/boot/dts/qcom-ipq8064-v1.0.dtsi
> +++ b/arch/arm/boot/dts/qcom-ipq8064-v1.0.dtsi
> @@ -92,34 +92,34 @@ leds {
>  			pinctrl-0 = <&leds_pins>;
>  			pinctrl-names = "default";
>  
> -			led@7 {
> +			led-0 {
>  				label = "led_usb1";
>  				gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
>  				linux,default-trigger = "usbdev";
>  				default-state = "off";
>  			};
>  
> -			led@8 {
> +			led-1 {
>  				label = "led_usb3";
>  				gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
>  				linux,default-trigger = "usbdev";
>  				default-state = "off";
>  			};
>  
> -			led@9 {
> +			led-2 {
>  				label = "status_led_fail";
>  				function = LED_FUNCTION_STATUS;
>  				gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
>  				default-state = "off";
>  			};
>  
> -			led@26 {
> +			led-3 {
>  				label = "sata_led";
>  				gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
>  				default-state = "off";
>  			};
>  
> -			led@53 {
> +			led-4 {
>  				label = "status_led_pass";
>  				function = LED_FUNCTION_STATUS;
>  				gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;