Re: [PATCH V3 1/2] dt-bindings: interrupt-controller: Add Loongson EIOINTC

[Binbin Zhou]

On Thu, Apr 20, 2023 at 4:09 AM Krzysztof Kozlowski
<krzysztof.kozlowski@xxxxxxxxxx> wrote:
>
> On 19/04/2023 09:17, Binbin Zhou wrote:
> > Add Loongson Extended I/O Interrupt controller binding with DT schema
> > format using json-schema.
> >
> > Signed-off-by: Binbin Zhou <zhoubinbin@xxxxxxxxxxx>
> > ---
> >  .../loongson,eiointc.yaml                     | 74 +++++++++++++++++++
> >  1 file changed, 74 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/interrupt-controller/loongson,eiointc.yaml
> >
> > diff --git a/Documentation/devicetree/bindings/interrupt-controller/loongson,eiointc.yaml b/Documentation/devicetree/bindings/interrupt-controller/loongson,eiointc.yaml
> > new file mode 100644
> > index 000000000000..4ab4efb061e1
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/interrupt-controller/loongson,eiointc.yaml
> > @@ -0,0 +1,74 @@
> > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> > +%YAML 1.2
> > +---
> > +$id: http://devicetree.org/schemas/interrupt-controller/loongson,eiointc.yaml#
> > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > +
> > +title: Loongson Extended I/O Interrupt Controller
> > +
> > +maintainers:
> > +  - Binbin Zhou <zhoubinbin@xxxxxxxxxxx>
> > +
> > +description: |
> > +  This interrupt controller is found on the Loongson-3 family chips and
> > +  Loongson-2K series chips and is used to distribute interrupts directly to
> > +  individual cores without forwarding them through the HT's interrupt line.
> > +
> > +allOf:
> > +  - $ref: /schemas/interrupt-controller.yaml#
> > +
> > +properties:
> > +  compatible:
> > +    enum:
> > +      - loongson,ls2k0500-eiointc
> > +      - loongson,ls2k2000-eiointc
> > +
> > +  reg:
> > +    items:
> > +      - description: Interrupt enable registers
> > +      - description: Interrupt status registers
> > +      - description: Interrupt clear registers
> > +      - description: Interrupt routing configuration registers
> > +
> > +  reg-names:
> > +    items:
> > +      - const: enable
> > +      - const: status
> > +      - const: clear
> > +      - const: route
> > +
> > +  interrupts:
> > +    maxItems: 1
> > +
> > +  interrupt-controller: true
> > +
> > +  '#interrupt-cells':
> > +    const: 1
> > +
> > +required:
> > +  - compatible
> > +  - reg
> > +  - interrupts
> > +  - interrupt-controller
> > +  - '#interrupt-cells'
> > +
> > +unevaluatedProperties: false
> > +
> > +examples:
> > +  - |
> > +    eiointc: interrupt-controller@1fe11600 {
> > +      compatible = "loongson,ls2k0500-eiointc";
> > +      reg = <0x1fe11600 0x10>,
> > +            <0x1fe11700 0x10>,
> > +            <0x1fe11800 0x10>,
> > +            <0x1fe114c0 0x4>;
>
> Binding is OK, but are you sure you want to split the address space like
> this? It looks like two address spaces (enable+clear+status should be
> one). Are you sure this is correct?
>
Hi Krzysztof:

These registers are all in the range of chip configuration registers,
in the case of LS2K0500, which has a base address of 0x1fe10000.
However, the individual register addresses are not contiguous with
each other, and most are distributed across modules, so I feel that
they should be listed in detail as they are used.

Thanks.
Binbin

> Best regards,
> Krzysztof
>
>