[PATCH] thermal/drivers/sun8i: Fix some error handling paths in sun8i_ths_probe()

[Christophe JAILLET]

Should an error occur after calling sun8i_ths_resource_init() in the probe
function, some resources need to be released, as already done in the
.remove() function.

Switch to the devm_clk_get_enabled() helper and add a new devm_action to
turn sun8i_ths_resource_init() into a fully managed function.

This fixes the issue and removes some LoC at the same time.

Fixes: dccc5c3b6f30 ("thermal/drivers/sun8i: Add thermal driver for H6/H5/H3/A64/A83T/R40")
Signed-off-by: Christophe JAILLET <christophe.jaillet@xxxxxxxxxx>
---
This changes the order of the release functions, but should be fine.
---
 drivers/thermal/sun8i_thermal.c | 43 +++++++++------------------------
 1 file changed, 12 insertions(+), 31 deletions(-)

diff --git a/drivers/thermal/sun8i_thermal.c b/drivers/thermal/sun8i_thermal.c
index 793ddce72132..8f4c29bc85aa 100644
--- a/drivers/thermal/sun8i_thermal.c
+++ b/drivers/thermal/sun8i_thermal.c
@@ -319,6 +319,11 @@ static int sun8i_ths_calibrate(struct ths_device *tmdev)
 	return ret;
 }
 
+static void sun8i_ths_reset_control_assert(void *data)
+{
+	reset_control_assert(data);
+}
+
 static int sun8i_ths_resource_init(struct ths_device *tmdev)
 {
 	struct device *dev = tmdev->dev;
@@ -339,13 +344,13 @@ static int sun8i_ths_resource_init(struct ths_device *tmdev)
 		if (IS_ERR(tmdev->reset))
 			return PTR_ERR(tmdev->reset);
 
-		tmdev->bus_clk = devm_clk_get(&pdev->dev, "bus");
+		tmdev->bus_clk = devm_clk_get_enabled(&pdev->dev, "bus");
 		if (IS_ERR(tmdev->bus_clk))
 			return PTR_ERR(tmdev->bus_clk);
 	}
 
 	if (tmdev->chip->has_mod_clk) {
-		tmdev->mod_clk = devm_clk_get(&pdev->dev, "mod");
+		tmdev->mod_clk = devm_clk_get_enabled(&pdev->dev, "mod");
 		if (IS_ERR(tmdev->mod_clk))
 			return PTR_ERR(tmdev->mod_clk);
 	}
@@ -354,32 +359,20 @@ static int sun8i_ths_resource_init(struct ths_device *tmdev)
 	if (ret)
 		return ret;
 
-	ret = clk_prepare_enable(tmdev->bus_clk);
+	ret = devm_add_action_or_reset(dev, sun8i_ths_reset_control_assert,
+				       tmdev->reset);
 	if (ret)
-		goto assert_reset;
+		return ret;
 
 	ret = clk_set_rate(tmdev->mod_clk, 24000000);
 	if (ret)
-		goto bus_disable;
-
-	ret = clk_prepare_enable(tmdev->mod_clk);
-	if (ret)
-		goto bus_disable;
+		return ret;
 
 	ret = sun8i_ths_calibrate(tmdev);
 	if (ret)
-		goto mod_disable;
+		return ret;
 
 	return 0;
-
-mod_disable:
-	clk_disable_unprepare(tmdev->mod_clk);
-bus_disable:
-	clk_disable_unprepare(tmdev->bus_clk);
-assert_reset:
-	reset_control_assert(tmdev->reset);
-
-	return ret;
 }
 
 static int sun8i_h3_thermal_init(struct ths_device *tmdev)
@@ -530,17 +523,6 @@ static int sun8i_ths_probe(struct platform_device *pdev)
 	return 0;
 }
 
-static int sun8i_ths_remove(struct platform_device *pdev)
-{
-	struct ths_device *tmdev = platform_get_drvdata(pdev);
-
-	clk_disable_unprepare(tmdev->mod_clk);
-	clk_disable_unprepare(tmdev->bus_clk);
-	reset_control_assert(tmdev->reset);
-
-	return 0;
-}
-
 static const struct ths_thermal_chip sun8i_a83t_ths = {
 	.sensor_num = 3,
 	.scale = 705,
@@ -642,7 +624,6 @@ MODULE_DEVICE_TABLE(of, of_ths_match);
 
 static struct platform_driver ths_driver = {
 	.probe = sun8i_ths_probe,
-	.remove = sun8i_ths_remove,
 	.driver = {
 		.name = "sun8i-thermal",
 		.of_match_table = of_ths_match,
-- 
2.34.1