Re: [PATCH 20/20] interconnect: qcom: Divide clk rate by src node bus width

[Konrad Dybcio]

Note: the commit title is wrong (src -> dst obviously).
Thanks Stephan for spotting this.

Konrad

On 30.05.2023 12:20, Konrad Dybcio wrote:
> Ever since the introduction of SMD RPM ICC, we've been dividing the
> clock rate by the wrong bus width. This has resulted in:
> 
> - setting wrong (mostly too low) rates, affecting performance
>   - most often /2 or /4
>   - things like DDR never hit their full potential
>   - the rates were only correct if src bus width == dst bus width
>     for all src, dst pairs on a given bus
> 
> - Qualcomm using the same wrong logic in their BSP driver in msm-5.x
>   that ships in production devices today
> 
> - me losing my sanity trying to find this
> 
> Resolve it by using dst_qn, if it exists.
> 
> Fixes: 5e4e6c4d3ae0 ("interconnect: qcom: Add QCS404 interconnect provider driver")
> Signed-off-by: Konrad Dybcio <konrad.dybcio@xxxxxxxxxx>
> ---
>  drivers/interconnect/qcom/icc-rpm.c | 8 +++++---
>  1 file changed, 5 insertions(+), 3 deletions(-)
> 
> diff --git a/drivers/interconnect/qcom/icc-rpm.c b/drivers/interconnect/qcom/icc-rpm.c
> index 59be704364bb..58e2a8b1b7c3 100644
> --- a/drivers/interconnect/qcom/icc-rpm.c
> +++ b/drivers/interconnect/qcom/icc-rpm.c
> @@ -340,7 +340,7 @@ static void qcom_icc_bus_aggregate(struct icc_provider *provider,
>  static int qcom_icc_set(struct icc_node *src, struct icc_node *dst)
>  {
>  	struct qcom_icc_provider *qp;
> -	struct qcom_icc_node *src_qn = NULL, *dst_qn = NULL;
> +	struct qcom_icc_node *src_qn = NULL, *dst_qn = NULL, *qn = NULL;
>  	struct icc_provider *provider;
>  	u64 active_rate, sleep_rate;
>  	u64 agg_avg[QCOM_SMD_RPM_STATE_NUM], agg_peak[QCOM_SMD_RPM_STATE_NUM];
> @@ -353,6 +353,8 @@ static int qcom_icc_set(struct icc_node *src, struct icc_node *dst)
>  	provider = src->provider;
>  	qp = to_qcom_provider(provider);
>  
> +	qn = dst_qn ? dst_qn : src_qn;
> +
>  	qcom_icc_bus_aggregate(provider, agg_avg, agg_peak, &max_agg_avg);
>  
>  	ret = qcom_icc_rpm_set(src_qn, agg_avg);
> @@ -372,11 +374,11 @@ static int qcom_icc_set(struct icc_node *src, struct icc_node *dst)
>  	/* Intentionally keep the rates in kHz as that's what RPM accepts */
>  	active_rate = max(agg_avg[QCOM_SMD_RPM_ACTIVE_STATE],
>  			  agg_peak[QCOM_SMD_RPM_ACTIVE_STATE]);
> -	do_div(active_rate, src_qn->buswidth);
> +	do_div(active_rate, qn->buswidth);
>  
>  	sleep_rate = max(agg_avg[QCOM_SMD_RPM_SLEEP_STATE],
>  			 agg_peak[QCOM_SMD_RPM_SLEEP_STATE]);
> -	do_div(sleep_rate, src_qn->buswidth);
> +	do_div(sleep_rate, qn->buswidth);
>  
>  	/*
>  	 * Downstream checks whether the requested rate is zero, but it makes little sense
>