Re: [PATCH V2 1/3] mmc: sdhci-pci-gli: Add Genesys Logic GL9767 support

From: Adrian Hunter
Date: Wed May 31 2023 - 03:02:33 EST

Next message: Geert Uytterhoeven: "Re: [PATCH] linux/pci.h: add a dummy implement for pci_clear_master()"
Previous message: Willem de Bruijn: "RE: [PATCH net-next v4] net: ioctl: Use kernel memory on protocol ioctl callbacks"
In reply to: Victor Shih: "[PATCH V2 1/3] mmc: sdhci-pci-gli: Add Genesys Logic GL9767 support"
Next in thread: Victor Shih: "[PATCH V2 2/3] mmc: sdhci-pci-gli: Set SDR104's clock to 205MHz and enable SSC for GL9767"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

On 30/05/23 12:53, Victor Shih wrote:
> From: Victor Shih <victor.shih@xxxxxxxxxxxxxxxxxxx>
>
> Add support for the GL9767 chipset. GL9767 supports
> SD3 mode likes UHS-I SDR50, SDR104.
> Enable MSI interrupt for GL9767. Some platform do not
> support PCI INTx and devices can not work without
> interrupt.
>
> Signed-off-by: Ben Chuang <ben.chuang@xxxxxxxxxxxxxxxxxxx>
> Signed-off-by: Victor Shih <victor.shih@xxxxxxxxxxxxxxxxxxx>

Acked-by: Adrian Hunter <adrian.hunter@xxxxxxxxx>

> ---
> drivers/mmc/host/sdhci-pci-core.c | 1 +
> drivers/mmc/host/sdhci-pci-gli.c | 160 ++++++++++++++++++++++++++++++
> drivers/mmc/host/sdhci-pci.h | 2 +
> 3 files changed, 163 insertions(+)
>
> diff --git a/drivers/mmc/host/sdhci-pci-core.c b/drivers/mmc/host/sdhci-pci-core.c
> index 01975d145200..1c2572c0f012 100644
> --- a/drivers/mmc/host/sdhci-pci-core.c
> +++ b/drivers/mmc/host/sdhci-pci-core.c
> @@ -1903,6 +1903,7 @@ static const struct pci_device_id pci_ids[] = {
> SDHCI_PCI_DEVICE(GLI, 9750, gl9750),
> SDHCI_PCI_DEVICE(GLI, 9755, gl9755),
> SDHCI_PCI_DEVICE(GLI, 9763E, gl9763e),
> + SDHCI_PCI_DEVICE(GLI, 9767, gl9767),
> SDHCI_PCI_DEVICE_CLASS(AMD, SYSTEM_SDHCI, PCI_CLASS_MASK, amd),
> /* Generic SD host controller */
> {PCI_DEVICE_CLASS(SYSTEM_SDHCI, PCI_CLASS_MASK)},
> diff --git a/drivers/mmc/host/sdhci-pci-gli.c b/drivers/mmc/host/sdhci-pci-gli.c
> index 633a8ee8f8c5..3ed207b89d1a 100644
> --- a/drivers/mmc/host/sdhci-pci-gli.c
> +++ b/drivers/mmc/host/sdhci-pci-gli.c
> @@ -149,6 +149,32 @@
> #define PCI_GLI_9755_PM_CTRL 0xFC
> #define PCI_GLI_9755_PM_STATE GENMASK(1, 0)
>
> +#define SDHCI_GLI_9767_GM_BURST_SIZE 0x510
> +#define SDHCI_GLI_9767_GM_BURST_SIZE_AXI_ALWAYS_SET BIT(8)
> +
> +#define PCIE_GLI_9767_VHS 0x884
> +#define GLI_9767_VHS_REV GENMASK(19, 16)
> +#define GLI_9767_VHS_REV_R 0x0
> +#define GLI_9767_VHS_REV_M 0x1
> +#define GLI_9767_VHS_REV_W 0x2
> +
> +#define PCIE_GLI_9767_PWR_MACRO_CTL 0x8D0
> +#define PCIE_GLI_9767_PWR_MACRO_CTL_LOW_VOLTAGE GENMASK(3, 0)
> +#define PCIE_GLI_9767_PWR_MACRO_CTL_LD0_LOW_OUTPUT_VOLTAGE GENMASK(15, 12)
> +#define PCIE_GLI_9767_PWR_MACRO_CTL_LD0_LOW_OUTPUT_VOLTAGE_VALUE 0x7
> +#define PCIE_GLI_9767_PWR_MACRO_CTL_RCLK_AMPLITUDE_CTL GENMASK(29, 28)
> +#define PCIE_GLI_9767_PWR_MACRO_CTL_RCLK_AMPLITUDE_CTL_VALUE 0x3
> +
> +#define PCIE_GLI_9767_SCR 0x8E0
> +#define PCIE_GLI_9767_SCR_AUTO_AXI_W_BURST BIT(6)
> +#define PCIE_GLI_9767_SCR_AUTO_AXI_R_BURST BIT(7)
> +#define PCIE_GLI_9767_SCR_AXI_REQ BIT(9)
> +#define PCIE_GLI_9767_SCR_CARD_DET_PWR_SAVING_EN BIT(10)
> +#define PCIE_GLI_9767_SCR_SYSTEM_CLK_SELECT_MODE0 BIT(16)
> +#define PCIE_GLI_9767_SCR_SYSTEM_CLK_SELECT_MODE1 BIT(17)
> +#define PCIE_GLI_9767_SCR_CORE_PWR_D3_OFF BIT(21)
> +#define PCIE_GLI_9767_SCR_CFG_RST_DATA_LINK_DOWN BIT(30)
> +
> #define GLI_MAX_TUNING_LOOP 40
>
> /* Genesys Logic chipset */
> @@ -693,6 +719,89 @@ static void gl9755_hw_setting(struct sdhci_pci_slot *slot)
> gl9755_wt_off(pdev);
> }
>
> +static inline void gl9767_vhs_read(struct pci_dev *pdev)
> +{
> + u32 vhs_enable;
> + u32 vhs_value;
> +
> + pci_read_config_dword(pdev, PCIE_GLI_9767_VHS, &vhs_value);
> + vhs_enable = FIELD_GET(GLI_9767_VHS_REV, vhs_value);
> +
> + if (vhs_enable == GLI_9767_VHS_REV_R)
> + return;
> +
> + vhs_value &= ~GLI_9767_VHS_REV;
> + vhs_value |= FIELD_PREP(GLI_9767_VHS_REV, GLI_9767_VHS_REV_R);
> +
> + pci_write_config_dword(pdev, PCIE_GLI_9767_VHS, vhs_value);
> +}
> +
> +static inline void gl9767_vhs_write(struct pci_dev *pdev)
> +{
> + u32 vhs_enable;
> + u32 vhs_value;
> +
> + pci_read_config_dword(pdev, PCIE_GLI_9767_VHS, &vhs_value);
> + vhs_enable = FIELD_GET(GLI_9767_VHS_REV, vhs_value);
> +
> + if (vhs_enable == GLI_9767_VHS_REV_W)
> + return;
> +
> + vhs_value &= ~GLI_9767_VHS_REV;
> + vhs_value |= FIELD_PREP(GLI_9767_VHS_REV, GLI_9767_VHS_REV_W);
> +
> + pci_write_config_dword(pdev, PCIE_GLI_9767_VHS, vhs_value);
> +}
> +
> +static void gli_set_9767(struct sdhci_host *host)
> +{
> + u32 value;
> +
> + value = sdhci_readl(host, SDHCI_GLI_9767_GM_BURST_SIZE);
> + value &= ~SDHCI_GLI_9767_GM_BURST_SIZE_AXI_ALWAYS_SET;
> + sdhci_writel(host, value, SDHCI_GLI_9767_GM_BURST_SIZE);
> +}
> +
> +static void gl9767_hw_setting(struct sdhci_pci_slot *slot)
> +{
> + struct pci_dev *pdev = slot->chip->pdev;
> + u32 value;
> +
> + gl9767_vhs_write(pdev);
> +
> + pci_read_config_dword(pdev, PCIE_GLI_9767_PWR_MACRO_CTL, &value);
> + value &= ~(PCIE_GLI_9767_PWR_MACRO_CTL_LOW_VOLTAGE |
> + PCIE_GLI_9767_PWR_MACRO_CTL_LD0_LOW_OUTPUT_VOLTAGE |
> + PCIE_GLI_9767_PWR_MACRO_CTL_RCLK_AMPLITUDE_CTL);
> +
> + value |= PCIE_GLI_9767_PWR_MACRO_CTL_LOW_VOLTAGE |
> + FIELD_PREP(PCIE_GLI_9767_PWR_MACRO_CTL_LD0_LOW_OUTPUT_VOLTAGE,
> + PCIE_GLI_9767_PWR_MACRO_CTL_LD0_LOW_OUTPUT_VOLTAGE_VALUE) |
> + FIELD_PREP(PCIE_GLI_9767_PWR_MACRO_CTL_RCLK_AMPLITUDE_CTL,
> + PCIE_GLI_9767_PWR_MACRO_CTL_RCLK_AMPLITUDE_CTL_VALUE);
> + pci_write_config_dword(pdev, PCIE_GLI_9767_PWR_MACRO_CTL, value);
> +
> + pci_read_config_dword(pdev, PCIE_GLI_9767_SCR, &value);
> + value &= ~(PCIE_GLI_9767_SCR_SYSTEM_CLK_SELECT_MODE0 |
> + PCIE_GLI_9767_SCR_SYSTEM_CLK_SELECT_MODE1 |
> + PCIE_GLI_9767_SCR_CFG_RST_DATA_LINK_DOWN);
> +
> + value |= PCIE_GLI_9767_SCR_AUTO_AXI_W_BURST |
> + PCIE_GLI_9767_SCR_AUTO_AXI_R_BURST |
> + PCIE_GLI_9767_SCR_AXI_REQ |
> + PCIE_GLI_9767_SCR_CARD_DET_PWR_SAVING_EN |
> + PCIE_GLI_9767_SCR_CORE_PWR_D3_OFF;
> + pci_write_config_dword(pdev, PCIE_GLI_9767_SCR, value);
> +
> + gl9767_vhs_read(pdev);
> +}
> +
> +static void sdhci_gl9767_reset(struct sdhci_host *host, u8 mask)
> +{
> + sdhci_reset(host, mask);
> + gli_set_9767(host);
> +}
> +
> static int gli_probe_slot_gl9750(struct sdhci_pci_slot *slot)
> {
> struct sdhci_host *host = slot->host;
> @@ -717,6 +826,19 @@ static int gli_probe_slot_gl9755(struct sdhci_pci_slot *slot)
> return 0;
> }
>
> +static int gli_probe_slot_gl9767(struct sdhci_pci_slot *slot)
> +{
> + struct sdhci_host *host = slot->host;
> +
> + gli_set_9767(host);
> + gl9767_hw_setting(slot);
> + gli_pcie_enable_msi(slot);
> + slot->host->mmc->caps2 |= MMC_CAP2_NO_SDIO;
> + sdhci_enable_v4_mode(host);
> +
> + return 0;
> +}
> +
> static void sdhci_gli_voltage_switch(struct sdhci_host *host)
> {
> /*
> @@ -740,6 +862,25 @@ static void sdhci_gli_voltage_switch(struct sdhci_host *host)
> usleep_range(100000, 110000);
> }
>
> +static void sdhci_gl9767_voltage_switch(struct sdhci_host *host)
> +{
> + /*
> + * According to Section 3.6.1 signal voltage switch procedure in
> + * SD Host Controller Simplified Spec. 4.20, steps 6~8 are as
> + * follows:
> + * (6) Set 1.8V Signal Enable in the Host Control 2 register.
> + * (7) Wait 5ms. 1.8V voltage regulator shall be stable within this
> + * period.
> + * (8) If 1.8V Signal Enable is cleared by Host Controller, go to
> + * step (12).
> + *
> + * Wait 5ms after set 1.8V signal enable in Host Control 2 register
> + * to ensure 1.8V signal enable bit is set by GL9767.
> + *
> + */
> + usleep_range(5000, 5500);
> +}
> +
> static void sdhci_gl9750_reset(struct sdhci_host *host, u8 mask)
> {
> sdhci_reset(host, mask);
> @@ -1150,3 +1291,22 @@ const struct sdhci_pci_fixes sdhci_gl9763e = {
> #endif
> .add_host = gl9763e_add_host,
> };
> +
> +static const struct sdhci_ops sdhci_gl9767_ops = {
> + .set_clock = sdhci_set_clock,
> + .enable_dma = sdhci_pci_enable_dma,
> + .set_bus_width = sdhci_set_bus_width,
> + .reset = sdhci_gl9767_reset,
> + .set_uhs_signaling = sdhci_set_uhs_signaling,
> + .voltage_switch = sdhci_gl9767_voltage_switch,
> +};
> +
> +const struct sdhci_pci_fixes sdhci_gl9767 = {
> + .quirks = SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC,
> + .quirks2 = SDHCI_QUIRK2_BROKEN_DDR50,
> + .probe_slot = gli_probe_slot_gl9767,
> + .ops = &sdhci_gl9767_ops,
> +#ifdef CONFIG_PM_SLEEP
> + .resume = sdhci_pci_gli_resume,
> +#endif
> +};
> diff --git a/drivers/mmc/host/sdhci-pci.h b/drivers/mmc/host/sdhci-pci.h
> index 3661a224fb04..9c8863956381 100644
> --- a/drivers/mmc/host/sdhci-pci.h
> +++ b/drivers/mmc/host/sdhci-pci.h
> @@ -76,6 +76,7 @@
> #define PCI_DEVICE_ID_GLI_9755 0x9755
> #define PCI_DEVICE_ID_GLI_9750 0x9750
> #define PCI_DEVICE_ID_GLI_9763E 0xe763
> +#define PCI_DEVICE_ID_GLI_9767 0x9767
>
> /*
> * PCI device class and mask
> @@ -195,5 +196,6 @@ extern const struct sdhci_pci_fixes sdhci_o2;
> extern const struct sdhci_pci_fixes sdhci_gl9750;
> extern const struct sdhci_pci_fixes sdhci_gl9755;
> extern const struct sdhci_pci_fixes sdhci_gl9763e;
> +extern const struct sdhci_pci_fixes sdhci_gl9767;
>
> #endif /* __SDHCI_PCI_H */

Next message: Geert Uytterhoeven: "Re: [PATCH] linux/pci.h: add a dummy implement for pci_clear_master()"
Previous message: Willem de Bruijn: "RE: [PATCH net-next v4] net: ioctl: Use kernel memory on protocol ioctl callbacks"
In reply to: Victor Shih: "[PATCH V2 1/3] mmc: sdhci-pci-gli: Add Genesys Logic GL9767 support"
Next in thread: Victor Shih: "[PATCH V2 2/3] mmc: sdhci-pci-gli: Set SDR104's clock to 205MHz and enable SSC for GL9767"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]