[PATCH net-next v2 1/2] net: phy: micrel: Move KSZ9477 errata fixes to PHY driver

[Robert Hancock]

The ksz9477 DSA switch driver is currently updating some MMD registers
on the internal port PHYs to address some chip errata. However, these
errata are really a property of the PHY itself, not the switch they are
part of, so this is kind of a layering violation. It makes more sense for
these writes to be done inside the driver which binds to the PHY and not
the driver for the containing device.

This also addresses some issues where the ordering of when these writes
are done may have been incorrect, causing the link to erratically fail to
come up at the proper speed or at all. Doing this in the PHY driver
during config_init ensures that they happen before anything else tries to
change the state of the PHY on the port.

The new code also ensures that autonegotiation is disabled during the
register writes and re-enabled afterwards, as indicated by the latest
version of the errata documentation from Microchip.

Signed-off-by: Robert Hancock <robert.hancock@xxxxxxxxxx>
Reviewed-by: Andrew Lunn <andrew@xxxxxxx>
---
 drivers/net/phy/micrel.c | 75 +++++++++++++++++++++++++++++++++++++++-
 1 file changed, 74 insertions(+), 1 deletion(-)

diff --git a/drivers/net/phy/micrel.c b/drivers/net/phy/micrel.c
index 2094d49025a7..6d18ea19e442 100644
--- a/drivers/net/phy/micrel.c
+++ b/drivers/net/phy/micrel.c
@@ -1774,6 +1774,79 @@ static int ksz886x_read_status(struct phy_device *phydev)
 	return genphy_read_status(phydev);
 }
 
+struct ksz9477_errata_write {
+	u8 dev_addr;
+	u8 reg_addr;
+	u16 val;
+};
+
+static const struct ksz9477_errata_write ksz9477_errata_writes[] = {
+	 /* Register settings are needed to improve PHY receive performance */
+	{0x01, 0x6f, 0xdd0b},
+	{0x01, 0x8f, 0x6032},
+	{0x01, 0x9d, 0x248c},
+	{0x01, 0x75, 0x0060},
+	{0x01, 0xd3, 0x7777},
+	{0x1c, 0x06, 0x3008},
+	{0x1c, 0x08, 0x2000},
+
+	/* Transmit waveform amplitude can be improved (1000BASE-T, 100BASE-TX, 10BASE-Te) */
+	{0x1c, 0x04, 0x00d0},
+
+	/* Energy Efficient Ethernet (EEE) feature select must be manually disabled */
+	{0x07, 0x3c, 0x0000},
+
+	/* Register settings are required to meet data sheet supply current specifications */
+	{0x1c, 0x13, 0x6eff},
+	{0x1c, 0x14, 0xe6ff},
+	{0x1c, 0x15, 0x6eff},
+	{0x1c, 0x16, 0xe6ff},
+	{0x1c, 0x17, 0x00ff},
+	{0x1c, 0x18, 0x43ff},
+	{0x1c, 0x19, 0xc3ff},
+	{0x1c, 0x1a, 0x6fff},
+	{0x1c, 0x1b, 0x07ff},
+	{0x1c, 0x1c, 0x0fff},
+	{0x1c, 0x1d, 0xe7ff},
+	{0x1c, 0x1e, 0xefff},
+	{0x1c, 0x20, 0xeeee},
+};
+
+static int ksz9477_config_init(struct phy_device *phydev)
+{
+	int err;
+	int i;
+
+	/* Apply PHY settings to address errata listed in
+	 * KSZ9477, KSZ9897, KSZ9896, KSZ9567, KSZ8565
+	 * Silicon Errata and Data Sheet Clarification documents.
+	 *
+	 * Document notes: Before configuring the PHY MMD registers, it is
+	 * necessary to set the PHY to 100 Mbps speed with auto-negotiation
+	 * disabled by writing to register 0xN100-0xN101. After writing the
+	 * MMD registers, and after all errata workarounds that involve PHY
+	 * register settings, write register 0xN100-0xN101 again to enable
+	 * and restart auto-negotiation.
+	 */
+	err = phy_write(phydev, MII_BMCR, BMCR_SPEED100 | BMCR_FULLDPLX);
+	if (err)
+		return err;
+
+	for (i = 0; i < ARRAY_SIZE(ksz9477_errata_writes); ++i) {
+		const struct ksz9477_errata_write *errata = &ksz9477_errata_writes[i];
+
+		err = phy_write_mmd(phydev, errata->dev_addr, errata->reg_addr, errata->val);
+		if (err)
+			return err;
+	}
+
+	err = genphy_restart_aneg(phydev);
+	if (err)
+		return err;
+
+	return kszphy_config_init(phydev);
+}
+
 static int kszphy_get_sset_count(struct phy_device *phydev)
 {
 	return ARRAY_SIZE(kszphy_hw_stats);
@@ -4735,7 +4808,7 @@ static struct phy_driver ksphy_driver[] = {
 	.phy_id_mask	= MICREL_PHY_ID_MASK,
 	.name		= "Microchip KSZ9477",
 	/* PHY_GBIT_FEATURES */
-	.config_init	= kszphy_config_init,
+	.config_init	= ksz9477_config_init,
 	.config_intr	= kszphy_config_intr,
 	.handle_interrupt = kszphy_handle_interrupt,
 	.suspend	= genphy_suspend,
-- 
2.40.1