Re: [PATCH v5 3/3] PCI: qcom-ep: Add ICC bandwidth voting support
From: Krishna Chaitanya Chundru
Date: Tue Jun 27 2023 - 22:23:17 EST
On 6/27/2023 8:31 PM, Manivannan Sadhasivam wrote:
On Tue, Jun 27, 2023 at 06:31:31AM +0530, Krishna chaitanya chundru wrote:
Add support to vote for ICC bandwidth based on the link
speed and width.
This patch is inspired from pcie-qcom driver to add basic
interconnect support.
Reference: commit c4860af88d0c ("PCI: qcom: Add basic interconnect
support").
Signed-off-by: Krishna chaitanya chundru <quic_krichai@xxxxxxxxxxx>
---
drivers/pci/controller/dwc/pcie-qcom-ep.c | 73 +++++++++++++++++++++++++++++++
1 file changed, 73 insertions(+)
diff --git a/drivers/pci/controller/dwc/pcie-qcom-ep.c b/drivers/pci/controller/dwc/pcie-qcom-ep.c
index 1435f51..b613817 100644
--- a/drivers/pci/controller/dwc/pcie-qcom-ep.c
+++ b/drivers/pci/controller/dwc/pcie-qcom-ep.c
@@ -13,6 +13,7 @@
#include <linux/debugfs.h>
#include <linux/delay.h>
#include <linux/gpio/consumer.h>
+#include <linux/interconnect.h>
#include <linux/mfd/syscon.h>
#include <linux/phy/pcie.h>
#include <linux/phy/phy.h>
@@ -28,6 +29,7 @@
#define PARF_SYS_CTRL 0x00
#define PARF_DB_CTRL 0x10
#define PARF_PM_CTRL 0x20
+#define PARF_PM_STTS 0x24
#define PARF_MHI_CLOCK_RESET_CTRL 0x174
#define PARF_MHI_BASE_ADDR_LOWER 0x178
#define PARF_MHI_BASE_ADDR_UPPER 0x17c
@@ -128,11 +130,19 @@
/* DBI register fields */
#define DBI_CON_STATUS_POWER_STATE_MASK GENMASK(1, 0)
+#define DBI_LINKCTRLSTATUS 0x80
+#define DBI_LINKCTRLSTATUS_SHIFT 16
not used?
not using these macros so I removed them in next patch.
+
#define XMLH_LINK_UP 0x400
#define CORE_RESET_TIME_US_MIN 1000
#define CORE_RESET_TIME_US_MAX 1005
#define WAKE_DELAY_US 2000 /* 2 ms */
+#define PCIE_GEN1_BW_MBPS 250
+#define PCIE_GEN2_BW_MBPS 500
+#define PCIE_GEN3_BW_MBPS 985
+#define PCIE_GEN4_BW_MBPS 1969
+
#define to_pcie_ep(x) dev_get_drvdata((x)->dev)
enum qcom_pcie_ep_link_status {
@@ -178,6 +188,8 @@ struct qcom_pcie_ep {
struct phy *phy;
struct dentry *debugfs;
+ struct icc_path *icc_mem;
+
struct clk_bulk_data *clks;
int num_clks;
@@ -253,9 +265,51 @@ static void qcom_pcie_dw_stop_link(struct dw_pcie *pci)
disable_irq(pcie_ep->perst_irq);
}
+static void qcom_pcie_ep_icc_update(struct qcom_pcie_ep *pcie_ep)
+{
+ struct dw_pcie *pci = &pcie_ep->pci;
+ u32 offset, status, bw;
+ int speed, width;
+ int ret;
+
+ if (!pcie_ep->icc_mem)
+ return;
+
+ offset = dw_pcie_find_capability(pci, PCI_CAP_ID_EXP);
+ status = readw(pci->dbi_base + offset + PCI_EXP_LNKSTA);
+
+ speed = FIELD_GET(PCI_EXP_LNKSTA_CLS, status);
+ width = FIELD_GET(PCI_EXP_LNKSTA_NLW, status);
+
+ switch (speed) {
+ case 1:
+ bw = MBps_to_icc(PCIE_GEN1_BW_MBPS);
+ break;
+ case 2:
+ bw = MBps_to_icc(PCIE_GEN2_BW_MBPS);
+ break;
+ case 3:
+ bw = MBps_to_icc(PCIE_GEN3_BW_MBPS);
+ break;
+ default:
+ dev_warn(pci->dev, "using default GEN4 bandwidth\n");
+ fallthrough;
+ case 4:
+ bw = MBps_to_icc(PCIE_GEN4_BW_MBPS);
+ break;
+ }
+
+ ret = icc_set_bw(pcie_ep->icc_mem, 0, width * bw);
+ if (ret) {
+ dev_err(pci->dev, "failed to set interconnect bandwidth: %d\n",
+ ret);
No need of braces for single line.
done.
+ }
+}
+
static int qcom_pcie_enable_resources(struct qcom_pcie_ep *pcie_ep)
{
int ret;
+ struct dw_pcie *pci = &pcie_ep->pci;
ret = clk_bulk_prepare_enable(pcie_ep->num_clks, pcie_ep->clks);
if (ret)
@@ -277,6 +331,20 @@ static int qcom_pcie_enable_resources(struct qcom_pcie_ep *pcie_ep)
if (ret)
goto err_phy_exit;
+ /*
+ * Some Qualcomm platforms require interconnect bandwidth constraints
+ * to be set before enabling interconnect clocks.
+ *
+ * Set an initial peak bandwidth corresponding to single-lane Gen 1
+ * for the pcie-mem path.
+ */
+ ret = icc_set_bw(pcie_ep->icc_mem, 0, MBps_to_icc(PCIE_GEN1_BW_MBPS));
+ if (ret) {
+ dev_err(pci->dev, "failed to set interconnect bandwidth: %d\n",
+ ret);
+ goto err_phy_exit;
Again, you should power off the PHY in the case of error. err_phy_exit is not
doing that for you.
- Mani
added the code remove the phy power.
-KC
+ }
+
return 0;
err_phy_exit:
@@ -550,6 +618,10 @@ static int qcom_pcie_ep_get_resources(struct platform_device *pdev,
if (IS_ERR(pcie_ep->phy))
ret = PTR_ERR(pcie_ep->phy);
+ pcie_ep->icc_mem = devm_of_icc_get(dev, "pcie-mem");
+ if (IS_ERR(pcie_ep->icc_mem))
+ ret = PTR_ERR(pcie_ep->icc_mem);
+
return ret;
}
@@ -573,6 +645,7 @@ static irqreturn_t qcom_pcie_ep_global_irq_thread(int irq, void *data)
} else if (FIELD_GET(PARF_INT_ALL_BME, status)) {
dev_dbg(dev, "Received BME event. Link is enabled!\n");
pcie_ep->link_status = QCOM_PCIE_EP_LINK_ENABLED;
+ qcom_pcie_ep_icc_update(pcie_ep);
pci_epc_bme_notify(pci->ep.epc);
} else if (FIELD_GET(PARF_INT_ALL_PM_TURNOFF, status)) {
dev_dbg(dev, "Received PM Turn-off event! Entering L23\n");
--
2.7.4