[PATCH 2/4] pinctrl: amd: Drop pull up select configuration

[Mario Limonciello]

pinctrl-amd currently tries to program bit 19 of all GPIOs to select
either a 4kΩ or 8hΩ pull up, but this isn't what bit 19 does.  Bit
19 is marked as reserved, even in the latest platforms documentation.

Drop this programming functionality.

Signed-off-by: Mario Limonciello <mario.limonciello@xxxxxxx>
---
 drivers/pinctrl/pinctrl-amd.c | 16 ++++------------
 drivers/pinctrl/pinctrl-amd.h |  1 -
 2 files changed, 4 insertions(+), 13 deletions(-)

diff --git a/drivers/pinctrl/pinctrl-amd.c b/drivers/pinctrl/pinctrl-amd.c
index 02d9f9f245707..cd46a5200f9b4 100644
--- a/drivers/pinctrl/pinctrl-amd.c
+++ b/drivers/pinctrl/pinctrl-amd.c
@@ -221,7 +221,6 @@ static void amd_gpio_dbg_show(struct seq_file *s, struct gpio_chip *gc)
 	char *pin_sts;
 	char *interrupt_sts;
 	char *wake_sts;
-	char *pull_up_sel;
 	char *orientation;
 	char debounce_value[40];
 	char *debounce_enable;
@@ -329,14 +328,9 @@ static void amd_gpio_dbg_show(struct seq_file *s, struct gpio_chip *gc)
 			seq_printf(s, "   %s|", wake_sts);
 
 			if (pin_reg & BIT(PULL_UP_ENABLE_OFF)) {
-				if (pin_reg & BIT(PULL_UP_SEL_OFF))
-					pull_up_sel = "8k";
-				else
-					pull_up_sel = "4k";
-				seq_printf(s, "%s ↑|",
-					   pull_up_sel);
+				seq_puts(s, "  ↑ |");
 			} else if (pin_reg & BIT(PULL_DOWN_ENABLE_OFF)) {
-				seq_puts(s, "   ↓|");
+				seq_puts(s, "  ↓ |");
 			} else  {
 				seq_puts(s, "    |");
 			}
@@ -763,7 +757,7 @@ static int amd_pinconf_get(struct pinctrl_dev *pctldev,
 		break;
 
 	case PIN_CONFIG_BIAS_PULL_UP:
-		arg = (pin_reg >> PULL_UP_SEL_OFF) & (BIT(0) | BIT(1));
+		arg = (pin_reg >> PULL_UP_ENABLE_OFF) & BIT(0);
 		break;
 
 	case PIN_CONFIG_DRIVE_STRENGTH:
@@ -810,10 +804,8 @@ static int amd_pinconf_set(struct pinctrl_dev *pctldev, unsigned int pin,
 			break;
 
 		case PIN_CONFIG_BIAS_PULL_UP:
-			pin_reg &= ~BIT(PULL_UP_SEL_OFF);
-			pin_reg |= (arg & BIT(0)) << PULL_UP_SEL_OFF;
 			pin_reg &= ~BIT(PULL_UP_ENABLE_OFF);
-			pin_reg |= ((arg>>1) & BIT(0)) << PULL_UP_ENABLE_OFF;
+			pin_reg |= (arg & BIT(0)) << PULL_UP_ENABLE_OFF;
 			break;
 
 		case PIN_CONFIG_DRIVE_STRENGTH:
diff --git a/drivers/pinctrl/pinctrl-amd.h b/drivers/pinctrl/pinctrl-amd.h
index 1cf2d06bbd8c4..34c5c3e71fb26 100644
--- a/drivers/pinctrl/pinctrl-amd.h
+++ b/drivers/pinctrl/pinctrl-amd.h
@@ -36,7 +36,6 @@
 #define WAKE_CNTRL_OFF_S4               15
 #define PIN_STS_OFF			16
 #define DRV_STRENGTH_SEL_OFF		17
-#define PULL_UP_SEL_OFF			19
 #define PULL_UP_ENABLE_OFF		20
 #define PULL_DOWN_ENABLE_OFF		21
 #define OUTPUT_VALUE_OFF		22
-- 
2.34.1