[PATCH] usb: dwc3: Disable AutoRetry controller feature for dwc_usb3 v2.00a

[Jakub Vanek]

AutoRetry has been found to cause issues in this controller revision.
This feature allows the controller to send non-terminating/burst retry
ACKs (Retry=1 and Nump!=0) as opposed to terminating retry ACKs
(Retry=1 and Nump=0) to devices when a transaction error occurs.

Unfortunately, some USB devices do not retry transfers when
the controller sends them a non-terminating retry ACK. After the transfer
times out, the xHCI driver tries to resume normal operation of the
controller by sending a Stop Endpoint command to it. However, this
revision of the controller fails to respond to that command in this
state and the xHCI driver therefore gives up. This is reported via dmesg:

[sda] tag#29 uas_eh_abort_handler 0 uas-tag 1 inflight: CMD IN
[sda] tag#29 CDB: opcode=0x28 28 00 00 69 42 80 00 00 48 00
xhci-hcd: xHCI host not responding to stop endpoint command
xhci-hcd: xHCI host controller not responding, assume dead
xhci-hcd: HC died; cleaning up

This problem has been observed on Odroid HC2. This board has
an integrated JMS578 USB3-to-SATA bridge. The above problem could be
triggered by starting a read-heavy workload on an attached SSD.
After a while, the host controller would die and the SSD would disappear
from the system.

Reverting b138e23d3dff ("usb: dwc3: core: Enable AutoRetry feature in
the controller") stopped the issue from occurring on Odroid HC2.
As this problem hasn't been reported on other devices, disable
AutoRetry just for the dwc_usb3 revision v2.00a that the board SoC
(Exynos 5422) uses.

Fixes: b138e23d3dff ("usb: dwc3: core: Enable AutoRetry feature in the controller")
Link: https://lore.kernel.org/r/a21f34c04632d250cd0a78c7c6f4a1c9c7a43142.camel@xxxxxxxxx/
Link: https://forum.odroid.com/viewtopic.php?t=42630
Cc: stable@xxxxxxxxxxxxxxx
Cc: Mauro Ribeiro <mauro.ribeiro@xxxxxxxxxxxxxx>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@xxxxxxxxxx>
Suggested-by: Thinh Nguyen <Thinh.Nguyen@xxxxxxxxxxxx>
Signed-off-by: Jakub Vanek <linuxtardis@xxxxxxxxx>
---
 drivers/usb/dwc3/core.c | 10 ++++++++--
 1 file changed, 8 insertions(+), 2 deletions(-)

diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c
index d68958e151a7..d742fc882d7e 100644
--- a/drivers/usb/dwc3/core.c
+++ b/drivers/usb/dwc3/core.c
@@ -1218,9 +1218,15 @@ static int dwc3_core_init(struct dwc3 *dwc)
 		 * Host mode on seeing transaction errors(CRC errors or internal
 		 * overrun scenerios) on IN transfers to reply to the device
 		 * with a non-terminating retry ACK (i.e, an ACK transcation
-		 * packet with Retry=1 & Nump != 0)
+		 * packet with Retry=1 & Nump != 0).
+		 *
+		 * Do not enable this for DWC_usb3 v2.00a. This controller
+		 * revision stops responding to Stop Endpoint commands if
+		 * a USB device does not retry after a non-terminating retry
+		 * ACK is sent to it.
 		 */
-		reg |= DWC3_GUCTL_HSTINAUTORETRY;
+		if (!DWC3_VER_IS(DWC3, 200A))
+			reg |= DWC3_GUCTL_HSTINAUTORETRY;
 
 		dwc3_writel(dwc->regs, DWC3_GUCTL, reg);
 	}
-- 
2.25.1