Re: [PATCH v2 0/8] ARM: dts: stm32: lxa-tac: add Linux Automation GmbH TAC

[Alexandre TORGUE]

Hi Leonard

On 6/14/23 14:32, Leonard Göhrs wrote:
> The Linux Automation Test Automation Controller (LXA TAC)[1] is an embedded
> software development tool built around the Octavo Systems OSD32MP15x SiP.
>
> The device contains an eMMC for storage, a DSA-capable on board ethernet
> switch with two external ports, dual CAN busses, a power switch to turn
> a device under test on or off and some other I/O.
>
> As of now there are two STM32MP157 based hardware generations (Gen 1 and
> Gen 2) that have most of their hardware config in common.
> In the future there will also be a STM32MP153 based hardware generation.
>
> [1]: https://www.linux-automation.com/en/products/lxa-tac.html
>
> V1: https://lore.kernel.org/lkml/20230607115508.2964574-1-l.goehrs@xxxxxxxxxxxxxx/
>
> Changes since V1:
>
>    - Rebase on top of stm32-next as requested by Alexandre Torgue.
>    - Split addition of shineworld lh133k compatible into separate
>      vendor-prefix patch and panel-mipi-dbi-spi.yaml patch as suggested
>      by Conor Dooley.
>      Did not carry over the Reviewed-by: Rob Herring <robh@xxxxxxxxxx>
>      from the original patch due to the split.
>    - Drop "dt-bindings: gpio: pca9570: add gpio-line-names property"
>      as it is already in gpio/for-next.
>    - Replace "dt-bindings: can: m_can: add termination-{gpios,ohms}
>      properties" with a patch that replaces additionalProperties with
>      unevaluatedProperties in bosch,m_can.yaml, as suggested by
>      Rob Herring.
>    - Drop "dt-bindings: net: dsa: microchip: add missing spi-{cpha,cpol}
>      properties" as setting the correct SPI mode is the responsibility of the
>      driver (suggested by Rob Herring).
>    - Rename ethernet0_rgmii_pins_d pinctrl group to ethernet0_rgmii_pins_e
>      as the former is already taken in stm32-next, as suggested by
>      Alexandre Torgue.
>
> Leonard Göhrs (8):
>    dt-bindings: vendor-prefixes: Add prefix for ShineWorld Innovations
>    dt-bindings: display: panel: mipi-dbi-spi: add shineworld lh133k
>      compatible
>    dt-bindings: display: panel: mipi-dbi-spi: add spi-3wire property
>    dt-bindings: can: m_can: change from additional- to
>      unevaluatedProperties
>    dt-bindings: net: dsa: microchip: add interrupts property for ksz
>      switches
>    ARM: dts: stm32: Add pinmux groups for Linux Automation GmbH TAC
>    dt-bindings: arm: stm32: Add compatible string for Linux Automation
>      LXA TAC
>    ARM: dts: stm32: lxa-tac: add Linux Automation GmbH TAC
>
>   .../devicetree/bindings/arm/stm32/stm32.yaml  |   4 +-
>   .../display/panel/panel-mipi-dbi-spi.yaml     |   3 +
>   .../bindings/net/can/bosch,m_can.yaml         |   2 +-
>   .../bindings/net/dsa/microchip,ksz.yaml       |   3 +
>   .../devicetree/bindings/vendor-prefixes.yaml  |   2 +
>   arch/arm/boot/dts/Makefile                    |   2 +
>   arch/arm/boot/dts/stm32mp15-pinctrl.dtsi      | 129 ++++
>   .../arm/boot/dts/stm32mp157c-lxa-tac-gen1.dts |  93 +++
>   .../arm/boot/dts/stm32mp157c-lxa-tac-gen2.dts | 172 +++++
>   arch/arm/boot/dts/stm32mp15xc-lxa-tac.dtsi    | 610 ++++++++++++++++++
>   10 files changed, 1018 insertions(+), 2 deletions(-)
>   create mode 100644 arch/arm/boot/dts/stm32mp157c-lxa-tac-gen1.dts
>   create mode 100644 arch/arm/boot/dts/stm32mp157c-lxa-tac-gen2.dts
>   create mode 100644 arch/arm/boot/dts/stm32mp15xc-lxa-tac.dtsi
>
>
> base-commit: c9cb7e72e293141d0d6c1d74c26788d3a0605172

Patches 4 to 8 applied on stm32-next.

thanks
Alex