Re: [PATCH v4 10/11] mtd: spi-nor: spansion: switch s25hx_t to use vreg_offset for quad_enable()

[Takahiro Kuwano]

On 7/26/2023 4:52 PM, Tudor Ambarus wrote:
> All s25hx_t flashes have single or multi chip flavors and already use
> n_dice and vreg_offset in cypress_nor_sr_ready_and_clear. Switch s25hx_t
> to always use vreg_offset for the quad_enable() method, so that we use
> the same code base for both single and multi chip package flashes.
> 
> Signed-off-by: Tudor Ambarus <tudor.ambarus@xxxxxxxxxx>
> ---
>  drivers/mtd/spi-nor/spansion.c | 18 +++++++-----------
>  1 file changed, 7 insertions(+), 11 deletions(-)
> 
> diff --git a/drivers/mtd/spi-nor/spansion.c b/drivers/mtd/spi-nor/spansion.c
> index 30a3ffbfa381..6abef5b515a1 100644
> --- a/drivers/mtd/spi-nor/spansion.c
> +++ b/drivers/mtd/spi-nor/spansion.c
> @@ -24,8 +24,6 @@
>  #define SPINOR_REG_CYPRESS_STR1V					\
>  	(SPINOR_REG_CYPRESS_VREG + SPINOR_REG_CYPRESS_STR1)
>  #define SPINOR_REG_CYPRESS_CFR1			0x2
> -#define SPINOR_REG_CYPRESS_CFR1V					\
> -	(SPINOR_REG_CYPRESS_VREG + SPINOR_REG_CYPRESS_CFR1)
>  #define SPINOR_REG_CYPRESS_CFR1_QUAD_EN		BIT(1)	/* Quad Enable */
>  #define SPINOR_REG_CYPRESS_CFR2			0x3
>  #define SPINOR_REG_CYPRESS_CFR2V					\
> @@ -348,10 +346,6 @@ static int cypress_nor_quad_enable_volatile(struct spi_nor *nor)
>  	u8 i;
>  	int ret;
>  
> -	if (!params->n_dice)
> -		return cypress_nor_quad_enable_volatile_reg(nor,
> -						SPINOR_REG_CYPRESS_CFR1V);
> -
>  	for (i = 0; i < params->n_dice; i++) {
>  		addr = params->vreg_offset[i] + SPINOR_REG_CYPRESS_CFR1;
>  		ret = cypress_nor_quad_enable_volatile_reg(nor, addr);
> @@ -657,15 +651,17 @@ static int s25hx_t_late_init(struct spi_nor *nor)
>  {
>  	struct spi_nor_flash_parameter *params = nor->params;
>  
> +	if (!params->n_dice || !params->vreg_offset) {
> +		dev_err(nor->dev, "%s failed. The volatile register offset could not be retrieved from SFDP.\n",
> +			__func__);
> +		return -EOPNOTSUPP;
> +	}
> +
>  	/* Fast Read 4B requires mode cycles */
>  	params->reads[SNOR_CMD_READ_FAST].num_mode_clocks = 8;
> -
> +	params->ready = cypress_nor_sr_ready_and_clear;
>  	cypress_nor_ecc_init(nor);
>  
> -	/* Replace ready() with multi die version */
> -	if (params->n_dice)
> -		params->ready = cypress_nor_sr_ready_and_clear;
> -
>  	return 0;
>  }
>  

Tested-by: Takahiro Kuwano <Takahiro.Kuwano@xxxxxxxxxxxx>