Re: [PATCH] arm64: dts: ti: k3-j721s2-som-p0: Correct pinmux offset for ospi0

[Nishanth Menon]

On 18:26-20230801, Udit Kumar wrote:
> Due to non-addressable regions in J721S2 SOC wkup_pmx was split
> into four regions from wkup_pmx0 to wkup_pmx3.
> 
> After split while updating the pin mux references to newly defined
> four wkup_pmx, pin mux for OSPI0 was left.
> 
> Pin mux for OSPI0 is spread over two range wkup_pmx0
> and wkup_pmx1, along with correcting pin mux for ospi
> adding correct pin mux setting within ospi node.
> 
> Fixes: 6bc829ceea41 ("arm64: dts: ti: k3-j721s2: Fix wkup pinmux range")
> 
> Signed-off-by: Udit Kumar <u-kumar1@xxxxxx>
> ---
> Test log without patch
> https://gist.github.com/uditkumarti/41d3d7ccf278d4e00e6da349478e58aa
> (line 1192) reports pin mux is out of range for ospi
> 
> Test log with patch
> https://gist.github.com/uditkumarti/46999c99911c9ff3777493fbaea243c6
> 
>  arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi | 13 ++++++++++---
>  1 file changed, 10 insertions(+), 3 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
> index d57dd43da0ef..1a9d13237c2d 100644
> --- a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
> @@ -45,8 +45,6 @@ mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-default-pins {
>  			J721S2_WKUP_IOPAD(0x000, PIN_OUTPUT, 0) /* (D19) MCU_OSPI0_CLK */
>  			J721S2_WKUP_IOPAD(0x02c, PIN_OUTPUT, 0) /* (F15) MCU_OSPI0_CSn0 */
>  			J721S2_WKUP_IOPAD(0x030, PIN_OUTPUT, 0) /* (G17) MCU_OSPI0_CSn1 */
> -			J721S2_WKUP_IOPAD(0x038, PIN_OUTPUT, 0) /* (F14) MCU_OSPI0_CSn2 */
> -			J721S2_WKUP_IOPAD(0x03c, PIN_OUTPUT, 0) /* (F17) MCU_OSPI0_CSn3 */
>  			J721S2_WKUP_IOPAD(0x00c, PIN_INPUT, 0) /* (C19) MCU_OSPI0_D0 */
>  			J721S2_WKUP_IOPAD(0x010, PIN_INPUT, 0) /* (F16) MCU_OSPI0_D1 */
>  			J721S2_WKUP_IOPAD(0x014, PIN_INPUT, 0) /* (G15) MCU_OSPI0_D2 */
> @@ -61,6 +59,15 @@ J721S2_WKUP_IOPAD(0x004, PIN_INPUT, 0) /* (E20) MCU_OSPI0_LBCLKO */
>  	};
>  };
>  
> +&wkup_pmx1 {
> +	mcu_fss0_ospi0_pins1_default: mcu-fss0-ospi0-default-pins1 {
patternProperties:
  '-pins(-[0-9]+)?$|-pin$':

Unless we have a strong reason, I'd leave it as
mcu-fss0-ospi0-1-default-pins or something

But, please ensure we dont get warnings with:
https://lore.kernel.org/all/20230721082654.27036-1-tony@xxxxxxxxxxx/

(Side note: Linus W is on vacation, so it might be a few days for this
 to hit next)
> +		pinctrl-single,pins = <
> +			J721S2_WKUP_IOPAD(0x000, PIN_OUTPUT, 0) /* (F14) MCU_OSPI0_CSn2 */
> +			J721S2_WKUP_IOPAD(0x004, PIN_OUTPUT, 0) /* (F17) MCU_OSPI0_CSn3 */
> +		>;
> +	};
> +};
> +
>  &wkup_pmx2 {
>  	wkup_i2c0_pins_default: wkup-i2c0-default-pins {
>  		pinctrl-single,pins = <
> @@ -127,7 +134,7 @@ &main_mcan16 {
>  &ospi0 {
>  	status = "okay";
>  	pinctrl-names = "default";
> -	pinctrl-0 = <&mcu_fss0_ospi0_pins_default>;
> +	pinctrl-0 = <&mcu_fss0_ospi0_pins_default>, <&mcu_fss0_ospi0_pins1_default>;
>  
>  	flash@0 {
>  		compatible = "jedec,spi-nor";
> -- 
> 2.34.1
> 

-- 
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3  1A34 DDB5 849D 1736 249D