-----Original Message-----
From: Johannes Zink <j.zink@xxxxxxxxxxxxxx>
Sent: Tuesday, August 1, 2023 7:48 AM
To: Shenwei Wang <shenwei.wang@xxxxxxx>; Russell King
<linux@xxxxxxxxxxxxxxx>; David S. Miller <davem@xxxxxxxxxxxxx>; Eric
Dumazet <edumazet@xxxxxxxxxx>; Jakub Kicinski <kuba@xxxxxxxxxx>; Paolo
Abeni <pabeni@xxxxxxxxxx>; Maxime Coquelin
<mcoquelin.stm32@xxxxxxxxx>; Shawn Guo <shawnguo@xxxxxxxxxx>; Sascha
Hauer <s.hauer@xxxxxxxxxxxxxx>; Neil Armstrong <neil.armstrong@xxxxxxxxxx>;
Kevin Hilman <khilman@xxxxxxxxxxxx>; Vinod Koul <vkoul@xxxxxxxxxx>; Chen-
Yu Tsai <wens@xxxxxxxx>; Jernej Skrabec <jernej.skrabec@xxxxxxxxx>; Samuel
Holland <samuel@xxxxxxxxxxxx>
Cc: Giuseppe Cavallaro <peppe.cavallaro@xxxxxx>; Alexandre Torgue
<alexandre.torgue@xxxxxxxxxxx>; Jose Abreu <joabreu@xxxxxxxxxxxx>;
Pengutronix Kernel Team <kernel@xxxxxxxxxxxxxx>; Fabio Estevam
<festevam@xxxxxxxxx>; dl-linux-imx <linux-imx@xxxxxxx>; Jerome Brunet
<jbrunet@xxxxxxxxxxxx>; Martin Blumenstingl
<martin.blumenstingl@xxxxxxxxxxxxxx>; Bhupesh Sharma
<bhupesh.sharma@xxxxxxxxxx>; Nobuhiro Iwamatsu
<nobuhiro1.iwamatsu@xxxxxxxxxxxxx>; Simon Horman
<simon.horman@xxxxxxxxxxxx>; Andrew Halaney <ahalaney@xxxxxxxxxx>;
Bartosz Golaszewski <bartosz.golaszewski@xxxxxxxxxx>; Wong Vee Khee
<veekhee@xxxxxxxxx>; Revanth Kumar Uppala <ruppala@xxxxxxxxxx>; Jochen
Henneberg <jh@xxxxxxxxxxxxxxxxxxxxxxxxxx>; netdev@xxxxxxxxxxxxxxx; linux-
stm32@xxxxxxxxxxxxxxxxxxxxxxxxxxxx; linux-arm-kernel@xxxxxxxxxxxxxxxxxxx;
linux-kernel@xxxxxxxxxxxxxxx; linux-amlogic@xxxxxxxxxxxxxxxxxxx;
imx@xxxxxxxxxxxxxxx; Frank Li <frank.li@xxxxxxx>
Subject: [EXT] Re: [PATCH v3 net 2/2] net: stmmac: dwmac-imx: pause the TXC
clock in fixed-link
Caution: This is an external email. Please take care when clicking links or
opening attachments. When in doubt, report the message using the 'Report this
email' button
Hi Shenwei,
thanks for your patch.
On 7/31/23 18:19, Shenwei Wang wrote:
When using a fixed-link setup, certain devices like the SJA1105
require a small pause in the TXC clock line to enable their internal
tunable delay line (TDL).
If this is only required for some devices, is it safe to enforce this behaviour
unconditionally for any kind of fixed link devices connected to the MX93 EQOS
or could this possibly break for other devices?
It won't impact normal devices. The link layer hasn't built up yet.
Thanks,
Shenwei
Best regards
Johannes
To satisfy this requirement, this patch temporarily disables the TX
clock, and restarts it after a required period. This provides the
required silent interval on the clock line for SJA1105 to complete the
frequency transition and enable the internal TDLs.
So far we have only enabled this feature on the i.MX93 platform.
Signed-off-by: Shenwei Wang <shenwei.wang@xxxxxxx>
Reviewed-by: Frank Li <frank.li@xxxxxxx>
---
.../net/ethernet/stmicro/stmmac/dwmac-imx.c | 42 +++++++++++++++++++
1 file changed, 42 insertions(+)
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-imx.c
b/drivers/net/ethernet/stmicro/stmmac/dwmac-imx.c
index 53ee5a42c071..2e4173d099f3 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-imx.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-imx.c
@@ -32,6 +32,7 @@
#define GPR_ENET_QOS_RGMII_EN (0x1 << 21)
#define MX93_GPR_ENET_QOS_INTF_MODE_MASK GENMASK(3, 0)
+#define MX93_GPR_ENET_QOS_INTF_MASK GENMASK(3, 1)
#define MX93_GPR_ENET_QOS_INTF_SEL_MII (0x0 << 1)
#define MX93_GPR_ENET_QOS_INTF_SEL_RMII (0x4 << 1)
#define MX93_GPR_ENET_QOS_INTF_SEL_RGMII (0x1 << 1)
@@ -40,6 +41,7 @@
#define DMA_BUS_MODE 0x00001000
#define DMA_BUS_MODE_SFT_RESET (0x1 << 0)
#define RMII_RESET_SPEED (0x3 << 14)
+#define CTRL_SPEED_MASK GENMASK(15, 14)
struct imx_dwmac_ops {
u32 addr_width;
@@ -56,6 +58,7 @@ struct imx_priv_data {
struct regmap *intf_regmap;
u32 intf_reg_off;
bool rmii_refclk_ext;
+ void __iomem *base_addr;
const struct imx_dwmac_ops *ops;
struct plat_stmmacenet_data *plat_dat; @@ -212,6 +215,42 @@
static void imx_dwmac_fix_speed(void *priv, uint speed, uint mode)
dev_err(dwmac->dev, "failed to set tx rate %lu\n", rate);
}
+static void imx_dwmac_fix_speed_mx93(void *priv, uint speed, uint
+mode) {
+ struct imx_priv_data *dwmac = priv;
+ int ctrl, old_ctrl, iface;
+
+ imx_dwmac_fix_speed(priv, speed, mode);
+
+ if (!dwmac || mode != MLO_AN_FIXED)
+ return;
+
+ if (regmap_read(dwmac->intf_regmap, dwmac->intf_reg_off, &iface))
+ return;
+
+ iface &= MX93_GPR_ENET_QOS_INTF_MASK;
+ if (iface != MX93_GPR_ENET_QOS_INTF_SEL_RGMII)
+ return;
+
+ old_ctrl = readl(dwmac->base_addr + MAC_CTRL_REG);
+ ctrl = old_ctrl & ~CTRL_SPEED_MASK;
+ regmap_update_bits(dwmac->intf_regmap, dwmac->intf_reg_off,
+ MX93_GPR_ENET_QOS_INTF_MODE_MASK, 0);
+ writel(ctrl, dwmac->base_addr + MAC_CTRL_REG);
+
+ /* Ensure the settings for CTRL are applied and avoid CPU/Compiler
+ * reordering.
+ */
+ wmb();
+
+ usleep_range(10, 20);
+ iface |= MX93_GPR_ENET_QOS_CLK_GEN_EN;
+ regmap_update_bits(dwmac->intf_regmap, dwmac->intf_reg_off,
+ MX93_GPR_ENET_QOS_INTF_MODE_MASK, iface);
+
+ writel(old_ctrl, dwmac->base_addr + MAC_CTRL_REG); }
+
static int imx_dwmac_mx93_reset(void *priv, void __iomem *ioaddr)
{
struct plat_stmmacenet_data *plat_dat = priv; @@ -317,8 +356,11
@@ static int imx_dwmac_probe(struct platform_device *pdev)
plat_dat->exit = imx_dwmac_exit;
plat_dat->clks_config = imx_dwmac_clks_config;
plat_dat->fix_mac_speed = imx_dwmac_fix_speed;
+ if (of_machine_is_compatible("fsl,imx93"))
+ plat_dat->fix_mac_speed = imx_dwmac_fix_speed_mx93;
plat_dat->bsp_priv = dwmac;
dwmac->plat_dat = plat_dat;
+ dwmac->base_addr = stmmac_res.addr;
ret = imx_dwmac_clks_config(dwmac, true);
if (ret)
--
Pengutronix e.K. | Johannes Zink |
Steuerwalder Str. 21 |
https://www.pe/
ngutronix.de%2F&data=05%7C01%7Cshenwei.wang%40nxp.com%7C761fbb75c
1c24cfe091508db928d8ade%7C686ea1d3bc2b4c6fa92cd99c5c301635%7C0%7C
0%7C638264908852977732%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjA
wMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C3000%7C%7C%
7C&sdata=2l2zNfIaNnRJENmERehNae8g%2F%2BQqlxD2YRx7ksY2X%2BE%3D&r
eserved=0 |
31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686| Fax: +49-5121-206917-5555 |