Re: [PATCH] net: sfp: handle 100G/25G active optical cables in sfp_parse_support

[Russell King (Oracle)]

On Mon, Aug 14, 2023 at 02:12:22PM +0200, Josua Mayer wrote:
> Hi Russell,
> 
> Am 10.08.23 um 14:05 schrieb Russell King (Oracle):
> > On Thu, Aug 10, 2023 at 01:38:13PM +0200, Josua Mayer wrote:
> > > Hi Russell,
> > > 
> > > Am 10.08.23 um 12:39 schrieb Russell King (Oracle):
> > > > On Thu, Aug 10, 2023 at 11:48:17AM +0200, Josua Mayer wrote:
> > > > > Handle extended compliance code 0x1 (SFF8024_ECC_100G_25GAUI_C2M_AOC)
> > > > > for active optical cables supporting 25G and 100G speeds.
> > > > Thanks. I think I would like one extra change:
> > > > 
> > > > > +	case SFF8024_ECC_100G_25GAUI_C2M_AOC:
> > > > >    	case SFF8024_ECC_100GBASE_SR4_25GBASE_SR:
> > > > >    		phylink_set(modes, 100000baseSR4_Full);
> > > > Since SFPs are single lane, SR4 doesn't make sense (which requires
> > > > four lanes), and I shouldn't have added it when adding these modes.
> > > > It would be a good idea to drop that, or at least for the
> > > > addition of the SFF8024_ECC_100G_25GAUI_C2M_AOC case.
> > > > 
> > > Would it be okay changing 100000baseSR4 to 100000baseSR dropping the "4"?
> > Not for SFF8024_ECC_100GBASE_SR4_25GBASE_SR. SFF-8024 states for this
> > code:
> > 
> >           02h        100GBASE-SR4 or 25GBASE-SR
> > 
> > 100GBASE-SR4: IEEE 802.3 Physical Layer specification for 100 Gb/s using
> > 100GBASE-R encoding over four lanes of multimode fiber, with reach
> > up to at least 100 m. (See IEEE Std 802.3, Clause 95.)
> > 
> > 100GBASE-R encoding: The physical coding sublayer encoding defined in
> > Clause 82 for 100 Gb/s operation. (See IEEE Std 802.3, Clause 82.)
> > 
> > 25GBASE-SR: IEEE 802.3 Physical Layer specification for 25 Gb/s using
> > 25GBASE-R encoding over multimode fiber. (See IEEE Std 802.3, Clause 112.)
> > 
> > IEEE 802.3-2018 doesn't define 100GBASE-SR, so I assume that's a later
> > development, which would be 100GBASE-R encoding over one lane of fiber.
> > 
> > So, 100GBASE-SR and 100GBASE-SR4 are not equivalent, and since
> > SFF8024_ECC_100GBASE_SR4_25GBASE_SR specifies 100GBASE-SR4, that
> > being _four_ lanes of fiber, and SFP form-factor modules only being
> > capable of carrying a single lane, and sfp-bus.c only being for SFP
> > modules, 100GBASE-SR4 is just not relevant for our purposes in
> > sfp-bus.c - and it makes no sense to switch to 100GBASE-SR because
> > that is not what this code tells us.
> > 
> > 
> > For the SFF8024_ECC_100G_25GAUI_C2M_AOC in a SFP28 module, the SFP28
> > form factor only supports up to 28Gb/s, so that means the module is
> > definitely 25GBASE-R ethernet. So that also excludes 100G operation.
> Okay. So probably the simple correct solution is to make a seperate
> case SFF8024_ECC_100G_25GAUI_C2M_AO that only sets 25gbase-r, and
> 25000baseSR_Full.
> > 
> > So, until we see a module in the SFP form factor (implying a single
> > lane) that does operate at 100G speeds, I think we should omit it.
> > 
> > I'm also wondering whether we should check br_nom/br_max/br_min now,
> > so that if we have to check that in the future, we don't start causing
> > regressions. Knowing how module EEPROMs are randomly wrong, it would
> > be a good idea to start with something sensible and see whether any
> > fail. Bear in mind that br_nom doesn't always get set to the correct
> > value - for example, 1G operates at 1250Mbps, and the SFP MSA specifies
> > that br_nom should be 1300 for 1G ethernet, but some modules use 1200.
> > I guess start at the correct value and then adjust to allow a range
> > as we see more modules.
> I don't fully understand how you would like to use br_nom.
> I see e.g. in sfp-bus.c at the end of sfp_parse_support a mapping of bitrate
> to 1000/2500 baseX modes.
> Are you referring to this section?
> 
> However there are no baseX modes for 25Gbps in ethtool.h - only SR/KR/CR.

I'm thinking something like:

	case SFF8024_ECC_100G_25GAUI_C2M_AO:
		if (br_min <= 28000 && br_max >= 25000) {
			/* 25GBASE-R, possibly with FEC */
			__set_bit(PHY_INTERFACE_MODE_25GBASER, interfaces);
			/* Re-use 25000baseSR as there is no 25Gbase- suffix
			 * for this
			 */
			phylink_set(modes, 25000baseSR_Full);
		}
		break;

I don't know what the actual numerical values should be though.

-- 
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTP is here! 80Mbps down 10Mbps up. Decent connectivity at last!