Re: [PATCH] scsi: ata: Fix a race condition between scsi error handler and ahci interrupt

[Damien Le Moal]

On 8/14/23 22:20, Li Nan wrote:
> 
> 在 2023/8/14 15:50, Damien Le Moal 写道:
>> On 8/14/23 15:41, Li Nan wrote:
>>>> This is definitely not correct because EH may have been scheduled for a non
>>>> fatal action like a device revalidate or to get sense data for successful
>>>> commands. With this change, the port will NOT be frozen when a hard error IRQ
>>>> comes while EH is waiting to start, that is, while EH waits for all commands to
>>>> complete first.
>>>>
>>>
>>> Yeah, we should find a better way to fix it. Do you have any suggesstions?
>>>
>>>> Furthermore, if you get an IRQ that requires the port to be frozen, it means
>>>> that you had a failed command. In that case, the drive is in error state per
>>>> ATA specs and stops all communication until a read log 10h command is issued.
>>>> So you should never ever see 2 error IRQs one after the other. If you do, it
>>>> very likely means that you have buggy hardware.
>>>>
>>>> How do you get into this situation ? What adapter and disk are you using ?
>>>>
>>>
>>>   > How do you get into this situation ?
>>> The first IRQ is io error, the second IRQ is disk link flash break.
>>
>> What does "link flash break" mean ?
>>
>>>
>>>   > What adapter and disk are you using ?
>>> It is a disk developed by our company, but we think the same issue
>>> exists when using other disks.
>>
>> As I said, I find this situation highly suspect because if the first IRQ was to
>> signal an IO error that the drive reported, then per ATA specifications, the
>> drive should be in error mode and should NOT have transmitted any other FIS
>> after the SDB FIS that signaled the error. Nothing at all should come after that
>> error SDB FIS, until the host issues a read log 10h to get thee drive out of
>> error state.
>>
>> If this is a prototype device, I would recommend that you take an ATA bus trace
>> and verify the FIS traffic. Something fishy is going on with the drive in my
>> opinion.
>>
> 
> Thank you for your patient explanation. I'm sorry I didn't explain the
> problem clearly before. After discussing with my colleagues who know
> more about dirvers, Let me re-describe the problem.
> 
> The problem`s situation is the SATA link is quickly disconnected and 
> connected. For example, when an I/O error is processed in error handling 
> thread, the disk is manually removed and inserted, and the AHCI chip 
> reports a hot plug interrupt.
> 
> This scenario is not just an NCQ error, but a disk is removed and 
> quickly inserted before the error processing is completed. For the error 
> handling process, the disk status needs to be restored after the error 
> handling is complete.

In your original email, you showed:

interrupt                            scsi_eh

ahci_error_intr
  =>ata_port_freeze
    =>__ata_port_freeze
      =>ahci_freeze (turn IRQ off)
    =>ata_port_abort
      =>ata_port_schedule_eh
        =>shost->host_eh_scheduled++;
        host_eh_scheduled = 1
                                     scsi_error_handler
                                       =>ata_scsi_error
                                         =>ata_scsi_port_error_handler
                                           =>ahci_error_handler
                                           . =>sata_pmp_error_handler
                                           .   =>ata_eh_thaw_port
                                           .     =>ahci_thaw (turn IRQ on)
ahci_error_intr                            .
  =>ata_port_freeze                        .
    =>__ata_port_freeze                    .
      =>ahci_freeze (turn IRQ off)         .
    =>ata_port_abort                       .
      =>ata_port_schedule_eh               .
        =>shost->host_eh_scheduled++;      .
        host_eh_scheduled = 2              .

But here, I do not understand how host_eh_scheduled can be incremented since the
shost state should still be SHOST_RECOVERY until scsi_restart_operations() is
called at the end of scsi_error_handler(), which is after ata_std_end_eh() is
executed toward the end of ata_scsi_port_error_handler().
Not sure how what you are showing here can happen. Can you have a closer look ?

                                           =>ata_std_end_eh
                                             =>host->host_eh_scheduled = 0;

In any case, for you particular failure pattern, given that the disk "goes away"
while EH is running, I would expect the commands executed during EH (e.g. read
log 10h) to timeout, which would cause a reset and a revalidate after that. The
reset should clear the port interrupt error bits, which should allow everything
to recover after aborting all commands caught by the first EH run.

-- 
Damien Le Moal
Western Digital Research