[PATCH 6/8] phy: exynos5-usbdrd: Add Exynos850 support
From: Sam Protsenko
Date: Fri Aug 18 2023 - 23:19:06 EST
Implement Exynos850 USB 2.0 DRD PHY controller support. Exynos850 has
quite a different PHY controller than Exynos5 compatible controllers,
but it's still possible to implement it on top of existing
exynos5-usbdrd driver infrastructure.
Only UTMI+ (USB 2.0) PHY interface is implemented, as Exynos850 doesn't
support USB 3.0.
Only two clocks are used for this controller:
- phy: bus clock, used for PHY registers access
- ref: PHY reference clock (OSCCLK)
Signed-off-by: Sam Protsenko <semen.protsenko@xxxxxxxxxx>
---
drivers/phy/samsung/phy-exynos5-usbdrd.c | 169 +++++++++++++++++++++++
1 file changed, 169 insertions(+)
diff --git a/drivers/phy/samsung/phy-exynos5-usbdrd.c b/drivers/phy/samsung/phy-exynos5-usbdrd.c
index 41508db87b9b..3f310b28bfff 100644
--- a/drivers/phy/samsung/phy-exynos5-usbdrd.c
+++ b/drivers/phy/samsung/phy-exynos5-usbdrd.c
@@ -145,6 +145,34 @@
#define LANE0_TX_DEBUG_RXDET_MEAS_TIME_62M5 (0x20 << 4)
#define LANE0_TX_DEBUG_RXDET_MEAS_TIME_96M_100M (0x40 << 4)
+/* Exynos850: USB DRD PHY registers */
+#define EXYNOS850_DRD_LINKCTRL 0x04
+#define LINKCTRL_BUS_FILTER_BYPASS(_x) ((_x) << 4)
+#define LINKCTRL_FORCE_QACT BIT(8)
+
+#define EXYNOS850_DRD_CLKRST 0x20
+#define CLKRST_LINK_SW_RST BIT(0)
+#define CLKRST_PORT_RST BIT(1)
+#define CLKRST_PHY_SW_RST BIT(3)
+
+#define EXYNOS850_DRD_UTMI 0x50
+#define UTMI_FORCE_SLEEP BIT(0)
+#define UTMI_FORCE_SUSPEND BIT(1)
+#define UTMI_DM_PULLDOWN BIT(2)
+#define UTMI_DP_PULLDOWN BIT(3)
+#define UTMI_FORCE_BVALID BIT(4)
+#define UTMI_FORCE_VBUSVALID BIT(5)
+
+#define EXYNOS850_DRD_HSP 0x54
+#define HSP_COMMONONN BIT(8)
+#define HSP_EN_UTMISUSPEND BIT(9)
+#define HSP_VBUSVLDEXT BIT(12)
+#define HSP_VBUSVLDEXTSEL BIT(13)
+#define HSP_FSV_OUT_EN BIT(24)
+
+#define EXYNOS850_DRD_HSP_TEST 0x5c
+#define HSP_TEST_SIDDQ BIT(24)
+
#define KHZ 1000
#define MHZ (KHZ * KHZ)
@@ -716,6 +744,129 @@ static const struct phy_ops exynos5_usbdrd_phy_ops = {
.owner = THIS_MODULE,
};
+static void exynos850_usbdrd_utmi_init(struct exynos5_usbdrd_phy *phy_drd)
+{
+ void __iomem *regs_base = phy_drd->reg_phy;
+ u32 reg;
+
+ /*
+ * Disable HWACG (hardware auto clock gating control). This will force
+ * QACTIVE signal in Q-Channel interface to HIGH level, to make sure
+ * the PHY clock is not gated by the hardware.
+ */
+ reg = readl(regs_base + EXYNOS850_DRD_LINKCTRL);
+ reg |= LINKCTRL_FORCE_QACT;
+ writel(reg, regs_base + EXYNOS850_DRD_LINKCTRL);
+
+ /* Start PHY Reset (POR=high) */
+ reg = readl(regs_base + EXYNOS850_DRD_CLKRST);
+ reg |= CLKRST_PHY_SW_RST;
+ writel(reg, regs_base + EXYNOS850_DRD_CLKRST);
+
+ /* Enable UTMI+ */
+ reg = readl(regs_base + EXYNOS850_DRD_UTMI);
+ reg &= ~(UTMI_FORCE_SUSPEND | UTMI_FORCE_SLEEP | UTMI_DP_PULLDOWN |
+ UTMI_DM_PULLDOWN);
+ writel(reg, regs_base + EXYNOS850_DRD_UTMI);
+
+ /* Set PHY clock and control HS PHY */
+ reg = readl(regs_base + EXYNOS850_DRD_HSP);
+ reg |= HSP_EN_UTMISUSPEND | HSP_COMMONONN;
+ writel(reg, regs_base + EXYNOS850_DRD_HSP);
+
+ /* Set VBUS Valid and D+ pull-up control by VBUS pad usage */
+ reg = readl(regs_base + EXYNOS850_DRD_LINKCTRL);
+ reg |= LINKCTRL_BUS_FILTER_BYPASS(0xf);
+ writel(reg, regs_base + EXYNOS850_DRD_LINKCTRL);
+
+ reg = readl(regs_base + EXYNOS850_DRD_UTMI);
+ reg |= UTMI_FORCE_BVALID | UTMI_FORCE_VBUSVALID;
+ writel(reg, regs_base + EXYNOS850_DRD_UTMI);
+
+ reg = readl(regs_base + EXYNOS850_DRD_HSP);
+ reg |= HSP_VBUSVLDEXT | HSP_VBUSVLDEXTSEL;
+ writel(reg, regs_base + EXYNOS850_DRD_HSP);
+
+ /* Power up PHY analog blocks */
+ reg = readl(regs_base + EXYNOS850_DRD_HSP_TEST);
+ reg &= ~HSP_TEST_SIDDQ;
+ writel(reg, regs_base + EXYNOS850_DRD_HSP_TEST);
+
+ /* Finish PHY reset (POR=low) */
+ udelay(10); /* required before doing POR=low */
+ reg = readl(regs_base + EXYNOS850_DRD_CLKRST);
+ reg &= ~(CLKRST_PHY_SW_RST | CLKRST_PORT_RST);
+ writel(reg, regs_base + EXYNOS850_DRD_CLKRST);
+ udelay(75); /* required after POR=low for guaranteed PHY clock */
+
+ /* Disable single ended signal out */
+ reg = readl(regs_base + EXYNOS850_DRD_HSP);
+ reg &= ~HSP_FSV_OUT_EN;
+ writel(reg, regs_base + EXYNOS850_DRD_HSP);
+}
+
+static int exynos850_usbdrd_phy_init(struct phy *phy)
+{
+ struct phy_usb_instance *inst = phy_get_drvdata(phy);
+ struct exynos5_usbdrd_phy *phy_drd = to_usbdrd_phy(inst);
+ int ret;
+
+ ret = clk_prepare_enable(phy_drd->clk);
+ if (ret)
+ return ret;
+
+ /* UTMI or PIPE3 specific init */
+ inst->phy_cfg->phy_init(phy_drd);
+
+ clk_disable_unprepare(phy_drd->clk);
+
+ return 0;
+}
+
+static int exynos850_usbdrd_phy_exit(struct phy *phy)
+{
+ struct phy_usb_instance *inst = phy_get_drvdata(phy);
+ struct exynos5_usbdrd_phy *phy_drd = to_usbdrd_phy(inst);
+ void __iomem *regs_base = phy_drd->reg_phy;
+ u32 reg;
+ int ret;
+
+ ret = clk_prepare_enable(phy_drd->clk);
+ if (ret)
+ return ret;
+
+ /* Set PHY clock and control HS PHY */
+ reg = readl(regs_base + EXYNOS850_DRD_UTMI);
+ reg &= ~(UTMI_DP_PULLDOWN | UTMI_DM_PULLDOWN);
+ reg |= UTMI_FORCE_SUSPEND | UTMI_FORCE_SLEEP;
+ writel(reg, regs_base + EXYNOS850_DRD_UTMI);
+
+ /* Power down PHY analog blocks */
+ reg = readl(regs_base + EXYNOS850_DRD_HSP_TEST);
+ reg |= HSP_TEST_SIDDQ;
+ writel(reg, regs_base + EXYNOS850_DRD_HSP_TEST);
+
+ /* Link reset */
+ reg = readl(regs_base + EXYNOS850_DRD_CLKRST);
+ reg |= CLKRST_LINK_SW_RST;
+ writel(reg, regs_base + EXYNOS850_DRD_CLKRST);
+ udelay(10); /* required before doing POR=low */
+ reg &= ~CLKRST_LINK_SW_RST;
+ writel(reg, regs_base + EXYNOS850_DRD_CLKRST);
+
+ clk_disable_unprepare(phy_drd->clk);
+
+ return 0;
+}
+
+static const struct phy_ops exynos850_usbdrd_phy_ops = {
+ .init = exynos850_usbdrd_phy_init,
+ .exit = exynos850_usbdrd_phy_exit,
+ .power_on = exynos5_usbdrd_phy_power_on,
+ .power_off = exynos5_usbdrd_phy_power_off,
+ .owner = THIS_MODULE,
+};
+
static int exynos5_usbdrd_phy_clk_handle(struct exynos5_usbdrd_phy *phy_drd)
{
unsigned long ref_rate;
@@ -782,6 +933,14 @@ static const struct exynos5_usbdrd_phy_config phy_cfg_exynos5[] = {
},
};
+static const struct exynos5_usbdrd_phy_config phy_cfg_exynos850[] = {
+ {
+ .id = EXYNOS5_DRDPHY_UTMI,
+ .phy_isol = exynos5_usbdrd_phy_isol,
+ .phy_init = exynos850_usbdrd_utmi_init,
+ },
+};
+
static const struct exynos5_usbdrd_phy_drvdata exynos5420_usbdrd_phy = {
.phy_cfg = phy_cfg_exynos5,
.phy_ops = &exynos5_usbdrd_phy_ops,
@@ -812,6 +971,13 @@ static const struct exynos5_usbdrd_phy_drvdata exynos7_usbdrd_phy = {
.has_common_clk_gate = false,
};
+static const struct exynos5_usbdrd_phy_drvdata exynos850_usbdrd_phy = {
+ .phy_cfg = phy_cfg_exynos850,
+ .phy_ops = &exynos850_usbdrd_phy_ops,
+ .pmu_offset_usbdrd0_phy = EXYNOS5_USBDRD_PHY_CONTROL,
+ .has_common_clk_gate = true,
+};
+
static const struct of_device_id exynos5_usbdrd_phy_of_match[] = {
{
.compatible = "samsung,exynos5250-usbdrd-phy",
@@ -825,6 +991,9 @@ static const struct of_device_id exynos5_usbdrd_phy_of_match[] = {
}, {
.compatible = "samsung,exynos7-usbdrd-phy",
.data = &exynos7_usbdrd_phy
+ }, {
+ .compatible = "samsung,exynos850-usbdrd-phy",
+ .data = &exynos850_usbdrd_phy
},
{ },
};
--
2.39.2