Re: [PATCH] arm: dts: bcm2711: Describe Ethernet LEDs

[Stefan Wahren]

Hi Florian,

Am 21.08.23 um 21:27 schrieb Florian Fainelli:
> Describe the Ethernet LEDs for the Raspberry Pi 4 model B board as well
> as the Raspberry Pi 4 CM board.
>
> Signed-off-by: Florian Fainelli <florian.fainelli@xxxxxxxxxxxx>
> ---
>   arch/arm/boot/dts/broadcom/bcm2711-rpi-4-b.dts | 18 ++++++++++++++++++
>   .../arm/boot/dts/broadcom/bcm2711-rpi-cm4.dtsi | 18 ++++++++++++++++++
>   2 files changed, 36 insertions(+)
>
> diff --git a/arch/arm/boot/dts/broadcom/bcm2711-rpi-4-b.dts b/arch/arm/boot/dts/broadcom/bcm2711-rpi-4-b.dts
> index d5f8823230db..41db78cb0836 100644
> --- a/arch/arm/boot/dts/broadcom/bcm2711-rpi-4-b.dts
> +++ b/arch/arm/boot/dts/broadcom/bcm2711-rpi-4-b.dts
> @@ -5,6 +5,7 @@
>   #include "bcm283x-rpi-led-deprecated.dtsi"
>   #include "bcm283x-rpi-usb-peripheral.dtsi"
>   #include "bcm283x-rpi-wifi-bt.dtsi"
> +#include <dt-bindings/leds/common.h>
>
>   / {
>   	compatible = "raspberrypi,4-model-b", "brcm,bcm2711";
> @@ -197,6 +198,23 @@ &genet_mdio {
>   	phy1: ethernet-phy@1 {
>   		/* No PHY interrupt */
>   		reg = <0x1>;
> +
> +		leds {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			leds@0 {
> +				color = <LED_COLOR_ID_GREEN>;
> +				default-state = "keep";
> +				reg = <0>;
> +			};
> +
> +			leds@1 {
> +				color = <LED_COLOR_ID_AMBER>;
> +				default-state = "keep";
> +				reg = <1>;
> +			};
> +		};
>   	};
>   };
>
> diff --git a/arch/arm/boot/dts/broadcom/bcm2711-rpi-cm4.dtsi b/arch/arm/boot/dts/broadcom/bcm2711-rpi-cm4.dtsi
> index 48e63ab7848c..3860a134d31a 100644
> --- a/arch/arm/boot/dts/broadcom/bcm2711-rpi-cm4.dtsi
> +++ b/arch/arm/boot/dts/broadcom/bcm2711-rpi-cm4.dtsi
> @@ -3,6 +3,7 @@
>   #include "bcm2711.dtsi"
>   #include "bcm2711-rpi.dtsi"
>   #include "bcm283x-rpi-wifi-bt.dtsi"
> +#include <dt-bindings/leds/common.h>
>
>   / {
>   	compatible = "raspberrypi,4-compute-module", "brcm,bcm2711";
> @@ -91,6 +92,23 @@ &genet_mdio {
>   	phy1: ethernet-phy@0 {
>   		/* No PHY interrupt */
>   		reg = <0x0>;
> +
> +		leds {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			leds@1 {
> +				color = <LED_COLOR_ID_GREEN>;
> +				default-state = "keep";
> +				reg = <1>;
> +			};
> +
> +			leds@2 {
> +				color = <LED_COLOR_ID_AMBER>;
> +				default-state = "keep";
> +				reg = <2>;
> +			};
> +		};

looking at my hardware setup, i see that the Ethernet PHY is located on
the compute module, but the Ethernet jack including the LEDs is located
on the IO board.

Maybe we should add the LEDs to the IO board dts?

Best regards

>   	};
>   };