Re: [PATCH 3/3] arm64: dts: qcom: ipq5018: enable the CPUFreq support

[Dmitry Baryshkov]

On Tue, 29 Aug 2023 at 13:59, Robert Marko <robimarko@xxxxxxxxx> wrote:
>
>
> On 29. 08. 2023. 12:12, Krzysztof Kozlowski wrote:
> > On 29/08/2023 11:54, Gokul Sriram Palanisamy wrote:
> >> Add the APCS, A53 PLL, cpu-opp-table nodes to set
> >> the CPU frequency at optimal range.
> >>
> >> Co-developed-by: Sricharan Ramabadhran <quic_srichara@xxxxxxxxxxx>
> >> Signed-off-by: Sricharan Ramabadhran <quic_srichara@xxxxxxxxxxx>
> >> Signed-off-by: Gokul Sriram Palanisamy <quic_gokulsri@xxxxxxxxxxx>
> >> ---
> >>   arch/arm64/boot/dts/qcom/ipq5018.dtsi | 34 +++++++++++++++++++++++++++
> >>   1 file changed, 34 insertions(+)
> >>
> >> diff --git a/arch/arm64/boot/dts/qcom/ipq5018.dtsi b/arch/arm64/boot/dts/qcom/ipq5018.dtsi
> >> index 9f13d2dcdfd5..05843517312c 100644
> >> --- a/arch/arm64/boot/dts/qcom/ipq5018.dtsi
> >> +++ b/arch/arm64/boot/dts/qcom/ipq5018.dtsi
> >> @@ -8,6 +8,7 @@
> >>   #include <dt-bindings/interrupt-controller/arm-gic.h>
> >>   #include <dt-bindings/clock/qcom,gcc-ipq5018.h>
> >>   #include <dt-bindings/reset/qcom,gcc-ipq5018.h>
> >> +#include <dt-bindings/clock/qcom,apss-ipq.h>
> > c is before r.
> >
> >>
> >>   / {
> >>      interrupt-parent = <&intc>;
> >> @@ -36,6 +37,8 @@ CPU0: cpu@0 {
> >>                      reg = <0x0>;
> >>                      enable-method = "psci";
> >>                      next-level-cache = <&L2_0>;
> >> +                    clocks = <&apcs_glb APCS_ALIAS0_CORE_CLK>;
> >> +                    operating-points-v2 = <&cpu_opp_table>;
> >>              };
> >>
> >>              CPU1: cpu@1 {
> >> @@ -44,6 +47,8 @@ CPU1: cpu@1 {
> >>                      reg = <0x1>;
> >>                      enable-method = "psci";
> >>                      next-level-cache = <&L2_0>;
> >> +                    clocks = <&apcs_glb APCS_ALIAS0_CORE_CLK>;
> >> +                    operating-points-v2 = <&cpu_opp_table>;
> >>              };
> >>
> >>              L2_0: l2-cache {
> >> @@ -54,6 +59,17 @@ L2_0: l2-cache {
> >>              };
> >>      };
> >>
> >> +    cpu_opp_table: opp-table-cpu {
> >> +            compatible = "operating-points-v2";
> >> +            opp-shared;
> >> +
> >> +            opp-1008000000 {
> >> +                    opp-hz = /bits/ 64 <1008000000>;
> >> +                    opp-microvolt = <1100000>;
> >> +                    clock-latency-ns = <200000>;
> > And the rest of OPPs?
> Hi Krzysztof,
> IPQ5018 only supports running at 1.1GHz, but its running at 800MHz
> by default from the bootloader so there is only one OPP.

If the bootloader sets it to 800 MHz, then this frequency is also
somehow 'supported', isn't it?

> I am glad to see more SoC-s gaining CPUFreq support.

Definitely.

>
> Regards,
> Robert
> >
> >> +            };
> >> +    };
> >> +
> >>      firmware {
> >>              scm {
> >>                      compatible = "qcom,scm-ipq5018", "qcom,scm";
> >> @@ -181,6 +197,24 @@ v2m1: v2m@1000 {
> >>                      };
> >>              };
> >>
> >> +            a53pll: clock@b116000 {
> >> +                    compatible = "qcom,ipq5018-a53pll";
> >> +                    reg = <0x0b116000 0x40>;
> >> +                    #clock-cells = <0>;
> >> +                    clocks = <&xo_board_clk>;
> >> +                    clock-names = "xo";
> >> +            };
> >> +
> >> +            apcs_glb: mailbox@b111000 {
> > 0xb111000 looks lower than 0x116000.
> >
> >> +                    compatible = "qcom,ipq5018-apcs-apps-global",
> >> +                                 "qcom,ipq6018-apcs-apps-global";
> >> +                    reg = <0x0b111000 0x1000>;
> > Best regards,
> > Krzysztof
> >
> >
> >



-- 
With best wishes
Dmitry