[PATCH 04/11] arm64: dts: qcom: pm7250b: make SID configurable

[Luca Weiss]

Like other Qualcomm PMICs the PM7250B can be used on different addresses
on the SPMI bus. Use similar defines like the PMK8350 to make this
possible.

Signed-off-by: Luca Weiss <luca.weiss@xxxxxxxxxxxxx>
---
 arch/arm64/boot/dts/qcom/pm7250b.dtsi | 23 ++++++++++++++++-------
 1 file changed, 16 insertions(+), 7 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/pm7250b.dtsi b/arch/arm64/boot/dts/qcom/pm7250b.dtsi
index e8540c36bd99..3514de536baa 100644
--- a/arch/arm64/boot/dts/qcom/pm7250b.dtsi
+++ b/arch/arm64/boot/dts/qcom/pm7250b.dtsi
@@ -7,6 +7,15 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/spmi/spmi.h>
 
+/* This PMIC can be configured to be at different SIDs */
+#ifndef PM7250B_SID
+	#define PM7250B_SID 2
+#endif
+
+#ifndef PM7250B_SID1
+	#define PM7250B_SID1 3
+#endif
+
 / {
 	thermal-zones {
 		pm7250b-thermal {
@@ -39,16 +48,16 @@ trip2 {
 };
 
 &spmi_bus {
-	pmic@2 {
+	pmic@PM7250B_SID {
 		compatible = "qcom,pm7250b", "qcom,spmi-pmic";
-		reg = <0x2 SPMI_USID>;
+		reg = <PM7250B_SID SPMI_USID>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 
 		pm7250b_temp: temp-alarm@2400 {
 			compatible = "qcom,spmi-temp-alarm";
 			reg = <0x2400>;
-			interrupts = <0x2 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
+			interrupts = <PM7250B_SID 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
 			io-channels = <&pm7250b_adc ADC5_DIE_TEMP>;
 			io-channel-names = "thermal";
 			#thermal-sensor-cells = <0>;
@@ -60,7 +69,7 @@ pm7250b_adc: adc@3100 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			#io-channel-cells = <1>;
-			interrupts = <0x2 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+			interrupts = <PM7250B_SID 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
 
 			channel@0 {
 				reg = <ADC5_REF_GND>;
@@ -141,7 +150,7 @@ channel@99 {
 		pm7250b_adc_tm: adc-tm@3500 {
 			compatible = "qcom,spmi-adc-tm5";
 			reg = <0x3500>;
-			interrupts = <0x2 0x35 0x0 IRQ_TYPE_EDGE_RISING>;
+			interrupts = <PM7250B_SID 0x35 0x0 IRQ_TYPE_EDGE_RISING>;
 			#thermal-sensor-cells = <1>;
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -159,9 +168,9 @@ pm7250b_gpios: pinctrl@c000 {
 		};
 	};
 
-	pmic@3 {
+	pmic@PM7250B_SID1 {
 		compatible = "qcom,pm7250b", "qcom,spmi-pmic";
-		reg = <0x3 SPMI_USID>;
+		reg = <PM7250B_SID1 SPMI_USID>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 	};

-- 
2.42.0